Відео

Thank you very much dear u are the best, i got new toureq24 , and i dont know if i can do it or not? as it will affect on other things

Will this work on my new Touareg -25 ?

So the hose connection was just for somewhere to bleed the line to other than in.?

What language is this guy speaking?

Great vid! What is the factory torque spec for the caliper 21mm bolts?

Very helpful, thanks a lot. Days searching this for a Tucson '06 2.0 diesel (D4EA).

Does this work on mild hybrid cars also ?? .. 2022 audi a3 (8Y)

Thanks for sharing your thoughts on this one

Great. Thanks. I suppose it is the same or similar on other VW models, such as the Nivus?

I am trying to change pads on my '20 SQ5 and am unable to slide the pads into position. Not aure what to do. Any advice? I can't get them to slidein with out taking out the anti-rattle clips.

Where is the parts list? you video volume is messed up. What type, Brand of front rotors are those??

Video is filled with common sense basics that often get overlooked by beginners and (fast moving) experts alike. Much appreciated, and the running "tips" commentary (without annoying techno music in the background) was extra nice.

Thank you so much for this information ! Could you please let us know what is the part number / name of the fan resistor that wasn’t working ? And how do you replace it ? Thanks 🙏

Thanks for the upload. My 05 sportage ran so hot that the felt pad over the coolant hose melted and started dripping down to the wire below. At first glance I thought it was the hose itself that melted. The hose is extremely hot to the touch even 5-10 minutes after car shuts off. I will ask my mechanic about thermostat and sensors.

I have a serious question. I have a Crown Vic 2009 P71. Exhaust system is stock 2in pipes with H-Pipe behind Cat. I want to mount 2 Flowmaster Straight through 71415 FlowFX behind H-pipe. Already have the mufflers. but have asked many on here for advice. No one bloody answers me. Should I reconnect the Flowmaster to the remaining stock pipe or should I go bigger? Flowmaster pipe diameter is 2,5in so I have to do a step up to fit it to stock. And step down to fit stock behind muffler. What will you recommend me doing?

You balancing a big vacuum and turbo..sequentiel

So I have a 2014 Touareg 7P with the battery under the passenger seat... would this method still work on my model ???

How hard is it to also do a clean job when doing this? Like thoroughly cleaning that super dirty caliper? Inside was like a disaster. Does it cost more to do a clean job? Or is it all the same?

Did you guys torqued the bolts?

What does this do to the cars battery? Would the charge cycle make the battery burn out faster due to over charging? Not a fire hazard I hope😅

May i know brake pad model and part number along with the rotor tks

What are the 10-litre oil brands and oil specs can you use? also 5w-30 or 10w-40?

Great video just did mine using your video. Question is there only one brake wear sensor on the front ? Job was much more involved compared to my 996 Porsche. Rather fiddle to be honest but got it done. Caliper hardware was the most difficult but once I figured it out the other side was a breeze relatively speaking.

Thank you kindly. Very detail and clear.

Interesting… In the Audi manual they instruct you to retract the caliper and push the fluid back into the reservoir

Didn't need to use brake cleaner on new rotors? Edit- Ahh I see you did mention it at the very end of the video.

Air suspension is also disabeld

You’re the best 💪.. Thank you Sir 🫡

Do you have any break replacements videos for 2021 audi s5 b9.5?

thanks for this. need to do my brakes and nervous but will be rewarding

instead of bleeding the brakes , can i use obdeleven to open the calipers and close them once the new parts are in ? Cheers

hello. great video breaking down step by step. does this process also apply for a 22 s5 Sportback?

Is this the same process for an 18 plate A4 Avant?

Seems good, and fairly thorough. The only thing I would say is that you forgot to mention torquing the caliper bolts to the correct torque spec, and possibly adding some thread locker paste to the bolts as they're going to be prone to vibrations so wouldn't want them to work loose!

Audi does say remove the 21mm bolts to remove the bracket and caliper instead of the special bolts to do a brake job. Good job

Love this. But do you have to bleed the calipers once you are all done? Planning to do this next weekend on my S5

Sheesh

Где Ламборгини?Почему отметил,но не показал?-_-

Damn this joint is too sick!...this car is truly bad ass!!!

INSANE😍😍😍

This is one awful A90.

You mean Auschtralia?

How was the drone on highway cruising? I have stage 2 tune and looking for a good exhaust, not too loud nor droney when cruising

❤

What exhaust system and downpipe was installed

You need measure the height of the shims or the rockers will break under high rpm, ask me how I know 😐

Thank you

where is installation process^? The name of video is unfit!

I Mic shim and it was. 3mm. all the flat one were. the that size

wat cause them to break. I am running. stock every thing and my flat shim on number 3exhaust. side keeps breaking. and throwing my rocker arm off