Відео

I need one of these to test on my channel

Is it possible to set a light to a certain channel? Channel 4 for a spotlight for example.

I NEED FRANCHE MANUAL

HOW TO RESET HOT RC HT-8A (FACTORY VALUE) TO CONECTE WITHE SUBS RECEVER,BEFOR A CONNECTED WITHE F-08A

您能解释一下如何使用发射器 CT-8B 上的通道 9 和 10 吗？

how to update firmware? to run light control??

신형 ds-600 은 크루즈컨트롤이 50단계인데 이걸 줄일수있는 방법이 있나요..?

Hello, you can buy the old dc600 Is there any way? The new product is inconvenient because the cruise function is in 20 stages I remember the old is 6 steps..

i do not know how to read chinese, sorry

Can F-06A bind/connect to CT-600?

feed sad buying this remote without no endpoint setting.. wtf

Receiver ct600 same with receiver ct-6A?

Es un buen producto yo lo recomiendo yo lo tengo y funciona perfectamente y muy buena señal😍🎮👍

hi. how to unlock my remote control?

Por favor pongan subtitulos en español 😢

We enabled the mixing functions for channel 1 and 2. Unfortunately moving the stick forward and back will rotate the tank and moving the stick left/right will make it go forwards and backwards. Is there any way to solve this without modifying the controller hardware? You can of course tilt the controller and run it on the side, but... This is V2 controller with an LCD.

Very helpful.

Very helpful.

Hello can you tech me how to reset this controller

how to use lamp control with ct 6a?

At 0:39 the video says the first row is positive, middle pin negative. However this is incorrect. At 1:40 the plug has the red (positive) wire in the middle, black wire (negative) is on the right which is correct.

为什么不用中文说，配个英文字幕？ 都用机器人配音了，还选一个重口音的，说数字用的还是中文的，听着难受

how do you change the ct8a from Chinese to English?

Hello. I have a problem with same transmitter and reciever. I am turning on the reciever and pressing BIND button, after that I turn on the transmitter, it starts blinking and beeping. But it doesn't pair and it doesn't stop beeping-blinking. Can you help me to fix it?

How do i connect the controller to my computer, Not working on Real Flight Simulator

Dear Authorities Greetings I bought the HOTRC CT-4A remote control on Aliexpress about 1 month ago. But as of yesterday I wanted to install the product. I think the settings of this product are not configured. Servo motor works, Forward-Reverse Gas does not work. I have 4 KYRC brush ESC and 3 flycolor esc, none of them are active. How to factory reset this remote control. I did so much research, I couldn't find it anywhere. I would like your very urgent support.

Hello, I messed up all the settings of the remote control. How can I reset this remote control to factory settings? I request your urgent support.

Need help

That realistic lamp can be used without additional modul, right?

Can the remote receiver handle PPM signals ?

How do you set ,steering trim , driving trim , throttle trim ,etc. I have this control need help with this please @Hotrc

How to reset the setting 😢😢

Buonasera Quindi prende alimentazione direttamente dall'esc? Nel manuale dice massimo 12v Ma quindi se metto all'esc una batteria 4s che sono circa 14v non va bene?

How do we adjust or set steering trim, throttle trim , wheel trim etc. Need help

How do we adjust or set steering trim , throttle trim, speed trim, etc with this transmitter

@HOTRC, can you use the usb port as a joystick for simracing on a computer?

Can the F-01AT receiver be connected to the latest CT-8B 10channel transmitter?

Can the F-01AT receiver be connected to the latest CT-8B 10channel transmitter?

Can the F-01AT receiver be connected to the latest CT-8B 10channel transmitter?

Can the F-01AT receiver be connected to the latest CT-8B 10channel transmitter?

Can the F-01AT receiver be connected to the latest CT-8B 10channel transmitter?

How to update firmware?

@HOTRC can i use the usb to connect it on computer like a joystick t play race games please?

Why led blu end green on not connected to transmiter

is chanel e 3?

Not work

can you connect it to a computer and use it as joystick in race games?

Apakah sama untuk remote ct6a

Hi, i just bought the new CT8B..is it normal that the roller is tight and hard to press?