Відео

I had to do this for a lack of heat on the left side. There are a few screws in that silver metal bracket; I decided not to reinstall the really tough one. On the controller itself, there are two screws and a post. The one in the back is a bitch. Cut the head off of it and hand screw it in so that it acts as another post to keep the motor in position while the front screw holds it all in there.

I have a small leak by the #1 and #2 injectors on the left, but the right looks okay. Do you think you really needed to remove/replace the valve cover, or would new gaskets/grommets around the fuel injectors have done the trick? (I know preventive maintenance is a good idea, but I also believe in not messing with any seals that aren’t leaking.) Thanks in advance.

Thank you! I was going to throw it out, this is my second tineco with the first being replaced just outside of warranty. Sprayed some penetrating oil and got it spinning and then some PTFE afterwards to hopefully keep it going.

I am gonna try this today. My warranty expired September and repair is $106 If this works, I am going to be forever grateful. I'll keep you updated.

Have you not changed the pcv valve membrane?

What car and engine?

This video was very straight forward and very detailed to make the job easy. thanks

So is the crank case valve on the valve cover.

What’s the part number?

Dude! I used dry lube for locks as I didn’t want the silicone to harm anything but it worked!

This video help me figure out mine. Awesome, I stripped a screw at the bottom lol but big thanks

Thanks. Problem solved. Hope this solution last for a while.

It's a super solution, mine has same issue and after stressful attemps to solve the issue as there is no service center in my region, finally it works again with this simple method. Thanks for the idea.

You have no idea how happy you just made my wife! Ours has been broken for months, hours spent taking everything apart and cleaning it. Did a Google search this morning and came across your video and problem solved! It took me a few rounds of WD40 but it’s back to working great again. Thank you!!!!!!

I have a 17 passat this the 09g as well?

Thanks ❤️ it works.

Ribbed for her pleasure

Thank you for the video! Where did you buy the seal kits for the valve cover that includs the grommets?

Can you give part number or link for the fuel injector removal tool? Thanks

I know you measure the quatity that you drained and put the exact quantity back. However, the first stream of oil you drained after you removed the outer plug is the overflow. Once you refill with fresh oil, you get the temp to around 40 degrees Celsius then with the engine running you remove the outer drain plug again to remove the excess oil. That's how you set the correct level.

What do I do if my rpms got worse, I put brand new gaskets and a new crankcase ventilation valve, plus new spark plugs? Does sensors have anything to do with it because the diagnostic show the one needs to be changed.

Fuse 40,42,45 air bag

thank you, mine broke after 6 months and Tineco did nothing about fixing it, the screen on top doesn't work still but at least it's working again after 18 months broken.

Just ordered a new motor for my one off Ali express. The motor is actually sealed it’s the cover on the front that rusts and expands then stops the blades on the motor from spinning. If you take the cover off and sand it back then put it back on it also works. My one was so rusted I had order a new one. This can occur from using the wrong floor chemicals. Shouldn’t soap up otherwise ends up in the motor

Thanks for this video, I have a 2020 Passat same issue and I just picked up my car from the shop, they wanted $1000 for parts and labor. So I’ll try this with your video help.

Thanks for sharing the video. I was about to order a new one and not even mess with it. But I ran across your video looking for a video to see the easiest way to remove the button so I didn't have to do the trial and error method. Saved me a ton of time and $.

Fixed my floor 3, thanks!

Would you have the part # for those valve cover grommets that the fuel injectors go in? And what is the size of that fuel line tool? I'm seeing 19mm is common, but don't want to assume.

Good video BUT DO NOT torque to 20nm. Correct spec is 8nm plus 180 degree turn. I got FUCKED listening to this dude.

Thank you for making this video it never would have crossed my mind to do this. Also thanks for making the short and to the point.

You saved me too ! Great tip. Thanks !

Thank you!!!!

Thank you! I was just about to take it apart, 5 minutes later it's running again

I HAVE A 2008 VALANCHE FLEX FUEL AND MY AIR BAG LIGHT IS ON , I tried you solution whats next mine did not turn off?

I just watched your video on the valve cover gasket. Good stuff. Where did you get that online manual? Which web site?

One of the lines I think it’s the return you forgot the put the clamp back on. Great job and great video

My not beep when i take the Air out of the tire

When you say, “you should get this tool,” it would be very helpful, if you mention the name of the tool. The one you tightened the fuel lines with, is something I’ve never seen before, in my life.

Thanks for taking the time to make the video. Do you have to do anything special to change the injector o-rings or copper washers? Did you do anything to try to clean the injectors other than an external wipe-down?

Is it recommended to unhook the battery cables while doing this? Also did you have to pull the fuel pump relay and turn the engine over a few times to relieve the pressure from the fuel lines? I'm replacing the valve cover gasket on my brother-in-laws passat next week. Same exact car. Have plenty of experience on domestic vehicles but none on German.

Legend, been trying to fix it for 2 hours and this fixed it

This did not work for me.

Thank you! Worked perfectly!

thank you so much .. Greatings from Germany ;)

Thank you very much you saved my tineco. A dub of silicone spray in the hole on that rusty bolt and some spins with a thin stick fixed it. You saved me alot of time and money.

Thank you, i dont use it that often, that is probably why the debris dries out on the motor and gets stuck in place, i was about to put this in the garbage.

Awesome video! It worked for me too. Thanks heaps!

Thanks!! For video it worked 😊

Youre the best bro😊😊😊

My Amazon Basics Wireless Mouse caused both of my computers to freeze randomly -- on six different versions of Linux Mint. I installed my backup mouse (never been used) and it solved ALL the problems. Both boot drives were corrupted due to multiple times of having to do a hard power off and restart. A replacement Amazon mouse is only about $10, so I will buy a new one. The old one has lasted for ~ 6 to 8 hours per day for at least 6 years.