Відео

Always engine should be warmed up before you dump the oil. The drain plug is 12mm not 10

For everyone asking about the tape the top side is much easy to control the flow to get a clean finsh so the tape controls the bottom for a clean finish

Thank you for making this video. It helped me locate the oil plug and filter before changing the oil for the first time in my new-to-me 2020 Silverado. 😊

Impressive, under 6 minutes

Lol funny

You put a lot of trust in those tires, recommend blocking under truck for safety.

Used Sawzall to cut up my old Glastron boat, easy to do, took couple of days, hauled pieces to landfill. The I switch blades and cut up rusty old trailer, and scrapped the metal at a recycler. Course I still have the chevy 350 4 bolt main motor, which with effort could run again. But why?

im a 11 year old and i found this entertaining, thank you for teaching me your ways!

I gotta find a video tutorial on this bender

Great video, thank you! What is the service intervals for both of these?

Very well done! I wish someone would buy that old building and restore it. 3:10

Thank you

Nice job!

The end of the pipe was long enough for the magnets on the level. He also put the no dog on the top of the pipe when it was supposed to be on the bottom. There’s a concave on the bottom of the level before the screw.

Loved the video, especially the helicopter part 😂

hard way to make a living, but healthy and fun .

Are you allowed to keep arrowheads? I am confused about the laws.😮

How did this hold up?

Excellent content but the music was so loud I couldn't hear you but I got the idea thank you

Good Job Bro 👍

MPSS was explained to BP staff in Glasgow in 1988, they rejected it! In London they still did not get it. Even5ually after Conoco and Shaell, and the original supporters they got it! Exhausting to explain a multi discipline design to such a compartmentalized company.

Music is horrible

Is OW-20 good for a 2019 with 168,000 ?

I have a 4.3 engine

Arent those man made

I get my oil from Amazon. With the price of it these days I try to save every penny I can. $13 difference from Autozone for the 5 quart jug.

Now I have it. Thanks.

Heard helps to wet the concrete first to get a bond with the repair concrete. Instead of water what about using a Bonding Agent to wet the old stuff?

I would advice against using a finger instead make a 45 degree bevel on the outside the silicone will adhere better because there is no whisper thin layer at the edges

Always hand tighten filters, never wrench them on 😔

Instead of chalk , you can use butyltape and it ain’t messy

Thanks for the video 👍🏼

Hi, thanks for the video! Is there an oil filter for this engine?

Aaaaaayyyyyyyu Migueeelll

Thanks man, I was looking for a visual before I got under my truck and was looking for the size of the wrench and location of plug. You saved me time and effort.

Man this is a great video I’m going to fix a couple shingles and your video will help me a lot thanks

Very nicely done....

Cool video bro ! That is some clear water for sure !

Wind sock

dont you think you should be standing off to the side?

Rup whoever has to pull that

nice video.. best Ive seen in a while.. no rambling on, detailed video, NO GLOVES! (good man!) and measurements in milliliters .. not ounces! very good!

Fabulous ancient artefacts from so long ago. Best wishes from wet and windy Lancashire, England.

Why would you take off the anti dog before flipping it to bend other end of the offset

Thank you !

Hell of a offset

Great job. Thanks.

Me and my wife and our 2 kids went to St.Jo's for an afternoon while visiting Port A for a few days in the summer during tourist season and it was great! Nobody there but us! I recommend it.

I ain’t doin all lat. just buy factory bends 😭