Відео

What is the duration required for the microware to completely regenerate?

Thank you! What a graceful fix.

Super, my friend ! used it and happy with that

Gonna do it now, save myself 2 hours in the oven

Some reason my CPU is idling right around 60 so the fan just keeps going on and off, and when it's on it's at a super low speed which is somehow even more annoying. Going to look at adding a heatsink and/or putting in a bigger fan then using this trick.

Thanks for shareing! 😊

This was helpful thank you!

Absolute magic, sir. Thanks!

I'm setting my SV08 up this weekend, but I already have the Noctua fan. Still, this is the perfect solution for someone who just wants some peace and quiet when the machine is idle. Thank you for posting it!

If you were to purchase the Noctua NF-A4x10 24v fan and plug it in to the exact same spot the current 4010 fan is, would you still use this script "as written" or could/would you lower the target temp of 60 to something lower? (because of the much quieter Noctua fan). Or would you just leave the original printer.cfg file alone on the stock Sovol SV08 with the Noctua fan installed?

Can you put the link of the servomotor please ???

Thank you, Im new to printing in fact my SVO8 arrived today, just about ready to open the box and assembly it. What software did you use to edit the config, are you ssh into the printer or remote desktop into the printer?

There is a bad PWM-sound, when the fan is spinning under 10% speed. It's better to shut off the fan when it is spinning under e.g. 20% Here is the updated code with the tweak to avoid fan spinning useless unter 20% speed and making pwm noises (works with original fan, might not with other fan. Use at own risk and test if the fan spins up again after shutting down): [temperature_fan CPUfan] pin: PA1 kick_start_time: 0.5 max_power: 1.0 min_temp: 0 max_temp: 90 hardware_pwm: true target_temp: 57 sensor_type: temperature_host max_speed: 1.0 min_speed: 0.23 off_below: 0.25 control: pid pid_Kp: 2 pid_Ki: .5 pid_Kd: 0.25 pid_deriv_time: 5.0

I inserted the rows in the desciption in the printer.cfg an restarted the firmwarer, than I started a print and got a error : The value "fan3" is not a valid FAN And the print was canceled

I saw that I was mentioned by Gergo on his Gergo print 3D channel. One thing he got wrong.. it isn't my idea or my code! I'm just making it public! See my comments on the video!

I added it as well to /home/sovol/patch/printer.cfg In case I do a reset, this function wont get lost. Thank you so much! Stupid thing, I already bought an electronic fan controller with external temp. probe 😖

This is awesome!!

thanks for the great little code

Weird yours is set to min speed 0 but is running 10 percent?

Thanks for doing this! It’ll be easier to show others than trying to explain❣️

I read a review where someone said the fan was quieter. Not on mine. Driving me insane. Thank you.

What a legend

Awesome, So much better than listening to that fan even from my bedroom two rooms away...lol Thank you! Now if you could write code to put my printer into sleep mode, when I'm not using it like my Airfrier and a few other things, I would be eternally grateful..lol

Would this work with the Lotos 5500D CNC plasma? Thanks and awesome work.

Hi John, I'm having an issue with the bulky motor and mount i purchased. What are the spec's on the longer belt you originally used for your kits. I need a belt longer than the XL290 to mount my motor. Thanks for your help. DJ 😊

Thanks, very useful.

Do you think a blender or vegetable chopper would work

can you identify the motor better so I can figure out which one to order. Great video.

You sir are the greatest hero in 3d printing history!

Thank you for this; it's really helped. Eventually I'm going to install the new Noctua 24v fan to help with the noise when the fan does kick on, but for now, it's much better.

I find that when the fan speed is set to anything less than 100%, it's off and only on when the speed is 100%. I'm making this mod after changing out the fan to a Noctua 40mm PWM fan. Since the fan connection is only 2 pin, the PWM-ing is being done on the supply voltage to the fan and not the PWM control pin. Do you happen to know if fans with PWM control inputs don't do well with PWM-ed power?

Noice i knew the fan didnt need to be replaced, people buying ish they dont need to cuz of some youtuber said so

thankyou so much, my printer sounds so much better now. so much easier, and totally non-destructive compared to all the other fan mods for this printer I have seen on the internet. I have adjusted the settings a lil; target_temp being set to 36c (winter here at the moment, and this was around the lower end temps that I found the fan made some difference while at idle) min_speed: 0.05. (at 5% the fan sound was less of an odd sound than at 10%) totally worth a thumbs up an a subscribe!

What belt is that? Cheers

Please, where is the temperature measured from and which line in the definition connects to that temperature sensor?

Does not work for me with noctua 24V pwm. It is only a two point controller (on-off) so no linear ramp.

Just trying to look at powering one of these machines. Lost me at the 3D thing. I don't have one of those in my pocket.

thank you verry much 👍👍👍

Wonderful and super useful. I hope sovol updates the new versions. Thank you for posting

Its also worth swapping the fan out for a decent fan like a noctua or similar, so even when it does ramp up its a LOT quieter. Also creating a definition for the correct fan if youre going to add the enclosure at any point.

Just FYI, the fan3 definition is for the enclosure exhaust fan (included with the enclosure kit), not the controller bay fan. Better to create a new fan definition for your mod instead of changing the fan3 definition, so people won't run into problems when they install the enclosure kit.

Well done!!

This worked perfectly. Thanks so much!

Thanks man! I submitted your solution to Sovol so they can add it to the stock firmware. Was driving me crazy. Had my soldering iron already heated up ;-)

I need help I’m planning to buy a sewing machine for my sandal diy. What China made sewing machine model is best thanks good video

Hi Gidday from Australia I’m very amazed by your built and wish to copy your set up.. can you pls tell under what name do I search this kit on eBay or Amazon pls thanks,, keep up the good work👏👍👏👍

Hi John, do you know if you can use the Yeswelder Cut 55DS? I have one that is not the pro.

Do these work with the andonstar249s-m and all 3 lenses? I WILL ABSOLUTELY BUY A SET if you can confirm it? I sharpen knives for a side hustle, and the reflections off the edge and bevels are insane once I get to the stroping phase of my sharpening process. I'm looking for this as a solution to help me. I need to know what else I have to get for all 3 lenses if you can guide me? Do I need a screw on cap also that fits all 3 lenses? Thank you for this information. I hope this is my fix? Niko

Hey! Would you be willing to sell the STL files?

I tried this a couple of years ago with half-inch irrigation tubing and a pond pump. The problem is, once the hot water circulates out of the system, the water doesn’t stay hot for long. Eventually the water runs cold and you’re just circulating cold water again. The only way this works is if the water in the black tubing is given just enough time to heat up, and then is circulated into the pool. Rinse and repeat.