Відео

Water passage

Dm on instagram:Str8drop_mobileservice

Okay Run It 🔥🔥

🤟🏾

Appreciate it🤟🏾

@@Str8Drop26can you do full video of installation

Sorry for that will fix with future videos

Yes it’s possible I have videos on my like that

2023 body harness got put in and seats bolt in perfectly fine

@@Str8Drop26 wiring hook up fine with the 8th gen seats or needs to be changed?

It should be common knowledge buddy 🤦🏾‍♂️I was giving basic knowledge from there you should take off

How did you get the buttom stud out im literally stuck

@mikellbeltre3459 I went to autozone and got 2 of the same thread nuts but thinner than the original so I can put them both on the little stud thread that shows out. Once you have both nuts hand tight hold the outer nut with a tool and put a wrench on the inner nut and go counter clockwise. Now both nuts are tight on the stud. You are ready to remove the stud by putting again your wrench on the inner nut ONLY and turn wrench counterclockwise again without holding the outer nut. Might have to grind your wrench a little so it is thin enough to fit on the inner nut.

@@AntonAtancopy thank you so much i will try that tomorrow 🙏🙏🙏🙏

@mikellbeltre3459 I'm not sure why you are removing the water passage but in my case it was leaking coolant. Once I cleaned the surface on the engine block where the rubber o-ring sits, there was a little inperfection caused by corrosion. In case yours is the same and not perfectly smooth, I used red high temperature RTV silicone. Clean both surfaces with brake cleaner before applying silicone. When putting the stud back this time you put the wrench on the outer nut and turn clockwise. Goodluck!

@@AntonAtancopy im changing it because my tenioner threads are stripped

HMU I’ll tell you everything @1700tumz I have a 7th gen

Yes, it is prewired

Vest thing to do is replace the turn signal switch in the steering column with a switch. Ebay had them for $50 or $60. The foglights you buy will have to be clipped. The connectors they come with are useless. DO NOT cut an wires coming from your car. Get some terminal pins, connect them to the two wires coming from the foglight them run them thru the connectors coming from your car. The foglight connectors coming from your car are splitting from the headlights. You don't need to drill holes, run wire or cut into your max if you do it this way.

Depends how much you get the parts car from the auction

@@Str8Drop26 sayless my Z I peep some of your work on IG to!!

2 days in and out

Yes it’s connect to one harness on each side L&R

Im curious about mine I have sonar sensor error on dash but not sure if my car 2017 Max is supposed to even have them in the front i think its the s model anyway I have been eyeing the bumper because I need to take the bumper off to replace my signal bulb and a fog light bulb and then my driver side fog light is fine but it keeps falling in I noticed the bumper is held on with plastic zip ties I do have a crap load of push pins that were made for that model but I'm not sure what I'm actually supposed to connect the top of the bumper back with where they have the zip ties it's on both sides right where are the bumper connects in the wheel well with cover it to either of you could give me any suggestions I would be so grateful. I caught a mechanic around here and they wanted around $1,000 to do everything and I think that's ridiculous. Anyway I hope you all have a blessed day and thank you for this video

He put down 9k with them

@@Str8Drop26 he got one of them Maxes?

Hell naw they don’t to give him a car Or refund

@@Str8Drop26 Wayment? So they took his cash and didn’t give him a car?

Lil pp.

@@Texaslawnmowerwhat are you six? 💀

@@TexaslawnmowerBlud got mad

@@liljor13 nope

@@OpdFwah not mad just bored

No it’s not it looks like a box in my opinion

@@BraydenMcClelland10 ok.