Відео

did it work on portable or inverter generator?

I think the 2 hours rest makes charcoal build up insiden the gasifier, that's make the blue flame

Well done bud. I gotta build one.

Thank you very much ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤💯

❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

Agregar Gotas de agua al gasificador desde donde se enciende 1 o 2 gotas cada 3segundos y obtendras mejor resultado en tu llama , lograras agregar a esa mezcla hidrógeno obtenido del agua

Nice! I believe you would be a neighbor I would be happy to live next to. There might then be competing syngas generator projects, or perhaps a local power island project. Too much fun, really.

If you got it going make another video..lol

That’s a great looking gasifier! I just love the rumbling sound it makes

Thank you for your well explained videos

Good work Also watch my gasification plant

Enjoyed that, thanks! Don't worry about your audience's underwhelment at the lighting, I can assure you you tube views were quite excited 😂

I wanna build one little bigger to be installed on my boat to power my generator. Could you spare the plans ?

how to release the char from the bottom?

NICE GASIFIER.

START ENGINE ON GASOLINE....SLOWLY....USE....VALVES TO SWITCH TO WOOD GAS. NEED AIR VALVE AND WOOD GAS VALVE AT ENGINE, LISTEN TO RUNNING ENGINE. IT WILL TELL YOU WHAT IT NEEDS. MOVE VERY SLOWLY ON SWITCH OVER. NO GASOLINE LEAVE CHOKE OPEN. CHOKE IS GASOLINE START ONLY. TAPE OVER OTHER AIR FILTER HOLES. USE AIR VALVE FOR GASOLINE TOO.. ITS TRICKY BE PATENT.

I am interested in building of same equipment . Could you share the plans ?

The blue flame is perfect for cooking

From experience the reduction zone should be at least 200mm or more my straightefeid gasifier makes a super smal amount of tar , it's 250mm long en 140mm in diameter in my 2 stage gasifier en the raw gas doesn't have any tar !

You should be charging for this lol

The bluer the better, good job!

Reducing the voltage to 6V is essentially reducing the speed of your motor by half. Maybe you were pulling too fast at 12V for the filter, your combustion zone or for both.

I think whit the right modifications to the gasifier like heat recouberation for the air supply en pre drying inside the gasifier one can get a blue flame whitout filter! Even whit low grade woodchips as fuel, the biggest difference I found was modifying the air nozzles! ( look for the twin fire en dubble fire gasifier design )from experience filter bags just clog up in a few hours if not minutes 😅

Whit some modification on the air supply you can run on wood chips you can make them whit sticks en twigs not high quality blocks 😅this takes Les effort to because the chopper machine is doing Al the horribly dangerous work inside it 😊

Great!!!

Great job, in fact excellent!

Now you can run an engine on this! This is awesome result! If you soak a part of your woodchips aka filter media with canola oil it will remove even more tar compounds and impurities. Use it on a top or middle layer. Nevertheless, this is a fully working system.

You're doing a great fine tuning 👍

It's just a fairy tale. Thank you. Continue.

Were did you get the curved bell

Hello. I stopped watching porn films - I like your work. Thank you.

Amazing skills and awesome steel work!

Ow my this build is sick 😊

Excellent job!

New subscriber from🇵🇭

Thanks for the update mate

Would milled housing from aluminium work just as well for DIY blower? Asking for a friend...

It needs oxygen at inlet

"This whole process kinda stresses me out." Gave me a chuckle. That rumbling sounds like a resonant frequency similar to blowing over a bottle.

Anyone with a newer sealed wood burning stove has seen this gas in action. At ~ 451F (I measure at flue) the wood goes from yellow to a blue green plasma that forms about an inch above above the wood - this is the gasified wood. If you don't see this in your stove its burning too cold.

The wood gasifier may be a good replacement for solar Pv in winter time, as there’s not enough sun and heat of cooling the engine could heat up a building. Instead of running a car, such an engine could run a generator to load my batteries. Planning it now to get it ready for next winter.

Awesome work! Pine has a lot of tar and oils in it hence more orange flame, careful as it can clog up your genset. It would be very interesting to see your reactor running on charcoal! Charcoal is supposed to have the cleanest burn to give you a blue flame. Also adding a water drip to the grates will inject steam and produce more H2 as well. Would you be able to do a charcoal run and post your findings?

It is all about fuel/air mixture. As one of the comments below has already suggested you need another hole with the baffle (similar to a choke where you can control your mixture. Very nice output though! How did you execute the reactor area?

Ive been watching wood gasifier videos for 13 years , there isn't a woodgas video on UA-cam that i havent seen at least 5 times😂😂, Ive watched parts 1,2,3 of your build, the simplicity and detail, plus dimensions, have finally given me the confidence to actually attempt a build, I really appreciate that.

Congrats on a successful start. 2 things if I may. Injectors are dry firing, may want to disable them as well if you decide to run for a prolonged amounts of time and you need a better filter, if you look at the hose when you are accelerated it sucked a lot of moisture in, this is dangerous. Looking forward to your next videos!

Awesome reactor, great workmanship! Your flame is too orange, you want it to be more blue. As for a filter, try wood chips soaked in canola oil it will remove more tar and create a much cleaner output.

I would have two separate hoses/pipes coming into the generator and one sucking in fresh air and one coming from the gasifier..... Have valves on these so that you can control the gas and air flow... Just work on getting the mixture just right...

Can we run a 30kva gas generator on it for 5 to 6 hours

I am looking for proven plans for a wood chip gasifier. The material is like course sawdust.

Great setup and looks like a Professional jobt. I'd pay you to do one for me. 😁👍