Відео

@@ToprikBikes Shukran bro 😅👊👊

@@wessnation689 Thanks man 👊

Hii ilikua ya mteja. Last I checked hata aliiuza

It's all paint. Minus a few brand stickers on there

😂😂😂 Toys take priority for sure

Not sure if it's louder than a colony wasp, but it's pretty loud. I tinkered with the springs in mine and after riding for long periods of time, it's enough to get your ears ringing a little

Imekuwa daily driver sasa. Weka destination 😅😅

Tutapanga moja official, hizi hukua very random. 😅 Shukran bro👊👊

On the axle, they're 2 of those 6902 RS bearings on the drive and non drive side. But for good measure, chick them out and confirm since some hubs have different designs. While you're at it, check the bearings on the driver itself. If they're not rolling smooth on your finger they also need to get replaced. Most common size is usually 6802RS for that.

@@KamaarhKennthanks very much that helped allot

@@lutaWayne out of stock

@@marcedwards2464 thank you

@@radadiyaniral5093 true

@@geraldgikonyo9811 thanks man 👊

@@robertchapman4190 much appreciated fam. 🙏🙏

@@novocaine251 in some cases I do. But if I need a surface all clear it's much faster and easier to use paint stripper instead.

@KamaarhKenn oh, now I see. Thanks man.

@@geraldgikonyo9811 Flat rate for basrs and forks is usually 4,000/= and up. Depending on what design you want

@@geraldgikonyo9811 Thanks man

I'd have to check. I can't quite remember the title 😅

@KamaarhKenn Ok that would be awesome thank you! 🙏🏽

👊👊

Tukipanga ride tutatangaza. Most of these clips huwa errands tu 😅😅

@@superhornet81 I think that's the size. Locally we just call them freewheel bearings since they're the smallest ones you can get 😅. And the bearings go on the inside and the outside grooves of the driver

Thank you BTW, at least know I put the bearings back in the right place. I may end up having to replace it, what are the chances it's going to lock up on me with those 3 bearings missing

There's also different variations of these hubs. Others have sealed bearings for the driver but run ball bearings for the axle on both sides.

As per its design, you can't. The surfaces wouldn't allow for a sealed Bearing to sit. Plus the axle wouldn't be compatible either

There's a lot more in store. 😅😂😂👌

@@novocaine251 much appreciated man 👊👊

@@geraldgikonyo9811 thanks man 👊👊

@@geraldgikonyo9811 I appreciate the support brother 👏

Thank you so much 😀

Thank you 👊👊

It truly did, I didn't expect it to go that smooth either

Thanks fam 👊👊

Much appreciated fam 👊👊

Shukran bro 👊👊

👌👌

Appreciate it man 👊👊

@ of course bro

Had to try something different, glad it worked out too 😅

Nice. But I guess yours doesn't look as beat up as thos one was though 😅

@KamaarhKenn yeah. I even touched up the handlebars, seatpost and cranks a bit with a black spraycan. Your paint job though is insane.

@novocaine251 much appreciated fam 👏

Much appreciated fam

My laptop died a while back and I couldn't edit stuff, so for a while all I could do was film. But now I have a new setup and I'm trying to get videos out more often

Not sure what size.

6902 2RS

For that, I'd advise to either visit a bike shop/mechanic or find a donor hub and steal the nuts off of it. A lot of these nuts have different thread pitches and you might not find one that's a straight fit say from like a hardware store or some place

@KamaarhKenn Thanks for the info, I ended up finding it online from a bmx affiliate company called Porkchop BMX!

Nice. Safe rides man 👊

Mbaya sana 👌👌

Shell

I kinda laid it down a bit too thick in between coats so it turned out more of a satin rather than matt