Відео

Hey I haven't tested that out yet. But if you have the TIA portal PLCsim advanced it will work for sure. But unsure about the basic edition.

Sounds weird.. you get to choose language on the install. Don't know why sorry

@1lovgren actually it was instructing me to restart the PC before installation. Finally installed it successfully. Thanks 👍

When the Logo is there it should be ready to load the program into the HMI. I am not sure else what the problem could be sorry

I could check if I still got the code saved somewhere. But how to share it?

Hey. For the FX0N series PLC that I use in this video you can only use input x0 and x1. For other fx series I think you can use x2 and x3 too. You can check the manual I linked it in the description. And its not the memory bit that define the encoders input its the C251 parameter. The memory bits I use is just to trigger that parameter.

Hey I never used the alpha PLC so dont know about that one. One very cheap option I know of is to order a small control board from Amazon. They have boards that simulate FX1 and FX3 PLCs from Mitsubishi think they cost around 30-50€. Then you can download gx works 2 or GX developer free.

Hey I got mine from RS components. Its good site if living in Europe

This is for trial version. Not allowed to upload licensed version on UA-cam its against the terms of rules.

Hey! Thats a good question. I been thinking about the same thing but going through a virtual machine. Haven't tested it out yet myself so cant answer for sure but I would believe that the PLC need to be in same subnet range ( the first 3 parameters (192.168.50).x for example ) as your company IP. But I cant say for sure sorry. I will test this out later at some point when I get enough time. If you test it out before me and get it working I would love to hear from you!

​@@1lovgren thank you! And yes let's see what you come up with, I'll also test on my side, I think I have to add a allen Bradley stratix switch, which basically does a nat 1to1 and ip translation, like a guy in the middle that makes 3 dif ip families talk to each other.

@@jorgeavalos4429 I'd imagine you figured this out already, but for anyone else that stumbles across this: My PLC is on a separate VLAN/network and connects via a Cisco Managed Switch via the X2 port to a common network path for HMI connectivity with all PLCs in the plant. I was able to connect to my PLC across the gateway just fine, using the IP for port X2.

@@SXRacer519 hey!!! i'm still messing with this thing hehe, thanks for the reply, any chance you could make us a vid tutorial dude? I normally record with power point has a free option to record the whole screen for free!! lol, also having the same issue, with a beckhoff plc using twincat3, funny that I can ping and do stuff in one building that is 10.30.40.xxx but if the PC is at building that has 10.30.17.xxx I cant see beckhoff devices :/ and IT dep is struggling to see this trough .....

@@jorgeavalos4429 So a couple of things to check or have IT check, I don't know how big your IT department is as a whole or how intense your networking is, but to cross IP ranges that big you need to make sure your subnet allows that difference. I am far from well enough versed to say exactly what it needs to be, but if you're 255.255.254.0 it may or may not work, you could try 255.255.0.0 to see if that works, or get a number from your networking guy. I apologize if you know more than me already on this, but basically the subnet only allows a certain variance (to my understanding) depending on the binary value. so 255 means it has to be identical, and 254 allows a certain variance. 0 is anything goes, so last number has to be 0 more or less if you're using the full range. Another thing is your gateway setup; our managed switches/VLAN's use a gateway, generally the xxx.xxx.xxx.1 of each VLAN/IP range, and that allows cross plant connectivity. Ultimately your network switch should have a gateway setup, and the PC you're using should also have this under its IP settings. In my Siemens PLC, under the ethernet setup page there is an option for a "Router" which has to be filled in with the gateway IP, otherwise I can't ping my PLC from a different IP VLAN in my plant. It's possible your Beckhoff has a similar setup and that just needs to be filled in to allow you to ping across gateways, I'm not very familiar with Beckhoff as our use is very minimal and more black box than the rest of our plant. Third thing, you need to have your IT/Network guy make sure that there is connectivity between your 10.30.40.xxx and 10.30.17.xxx through the switch settings. It's possible they have this blocked, but if you can ping other things from that range, that's probably not the issue, I'd lean towards it being a gateway setup within the Beckhoff PLC or your Siemens PLC.

Hey. I think theres not much you can do about that. You either get an PNP encoder or maybe you can connect am extra input card with + voltage to the s/s com terminal

Thanks :)

LOGO! PLC use relay outputs

@@1lovgren thank you very much

Hey! I think one way to do it would be to extend the function block with another var_input where you connect your X000 tag. Then put it as a normally closed local label before the Q var_output inside of the function blocks programming rung. I could help you if you need help with it!

@@1lovgren thanks for the response, I would gladly appreciate some help. do you want to email me or me email you?

@@1lovgren would sure appreciate some help., can i email you or you email me?

@@1lovgren would appreciate some help, can i email you or you email me?

@@1lovgren I responded from my work account initially...sorry for the confusion.