- 30
- 92 979
Tecmike
Приєднався 2 лис 2012
Відео
2016-2019  Cadillac Escalade, GMC Yukon, Chevy, Tahoe, driver side motor amount shortcut
Переглядів 1622 місяці тому
 Engine mount driver side 2016 through 2019 Cadillac Escalade GMC Yukon Chevy Tahoe, shortcut removal and installation 
2015 Hyundai Sonata 2.4 p001 p2006 intake manifold, intake cam solenoid
Переглядів 1524 місяці тому
P001, p2006 2015 Hyundai Sonata 2.4 Intake manifold replacement Intake cam solenoid replacements
2013 Chevrolet traverse actuator X blend door heat AC actuator how to replace and diagnose
Переглядів 1525 місяців тому
2013 Chevy traverse AC heat, airflow vent control, diagnose and replace heat control module and blender
Jeep commander 3.7 timing cover removal / water pump / front main seal
Переглядів 1497 місяців тому
Jeep 3.7 timing cover removal / water pump / alternator / a/c compressor commander grand Cherokee
Dodge charger pursuit 5.7l radiator removal/replacement
Переглядів 460Рік тому
2016 dodge charger 5.7 HIMI radiator replacement
2019 jeep compass 3.4l awd starter replacement
Переглядів 8 тис.Рік тому
2019 Jeep compass 3.4l How to replace a starter on 2019 Jeep compass 3.4l Awd
Saab 93 2.0t / Gm 2.2 2.0 water pump replacement
Переглядів 846Рік тому
How to do a water pump on a Saab 93 2.0T /Gm 2.0/2.2 water pump replacement
2020 Mitsubishi outlander Electronic rear brakes replacement
Переглядів 17 тис.Рік тому
2020 Mitsubishi outlander Electronic rear brakes replacement
2019-2023 dodge ram 1500 bighorn 3.6 water pump replacement
Переглядів 6 тис.Рік тому
2019 dodge ram 3.6 water pump replacement Alternator removal
2012 2013 ford focus heat blower motor replacement
Переглядів 3,5 тис.Рік тому
2012-2020 ford focus heater blower motor replacement
2016 Toyota 4Runner rear axle seal replacement and axle removal
Переглядів 2,8 тис.Рік тому
2016 Toyota 4Runner rear axle removal and rear driver and passenger side axle seal replacement
2018-2021 Chevrolet Eqnox how to replace rear brakes with electronic E brakes
Переглядів 202 роки тому
2018-2021 Chevrolet Eqnox how to replace rear brakes with electronic E brakes
Fooling with my e36 m3 donuts after fresh oil change
Переглядів 322 роки тому
Fooling with my e36 m3 donuts after fresh oil change
Dodge Durango 3.6 AWD 2011-2016 starter replacement/ how to remove a starter
Переглядів 20 тис.2 роки тому
Dodge Durango 3.6 AWD 2011-2016 starter replacement/ how to remove a starter
2012 Dodge Journey tune up and compression test bad engine
Переглядів 6 тис.3 роки тому
2012 Dodge Journey tune up and compression test bad engine
Engine swap Range Rover رنج روفر سحب متور فك محرك رنج روفر بيوم واحد
Переглядів 4,5 тис.3 роки тому
Engine swap Range Rover رنج روفر سحب متور فك محرك رنج روفر بيوم واحد
Jeep Liberty How to remove a heater core
Переглядів 4 тис.4 роки тому
Jeep Liberty How to remove a heater core
Bmw e36 magna flow muffler sounds real nice
Переглядів 25010 років тому
Bmw e36 magna flow muffler sounds real nice
I did the pads and rotors. Everything was good for 2 days then the emergency brake light and warning buzzer comes on.
Thanks!
This is the better way watch other videos by other tubers and they are doing wrong and as slow as possible.
Would this be the same for a Mitsubishi eclipse cross?
@@vanessapsalm91 what year ?
If the seal has been bad for a while, replace the axle bearing. You can tell if it’s bad if the seal goes bad again very soon. What happens is the diff fluid washed the grease out of the sealed bearing. Then the bearing gets slight play and wipes out the seal.
The best
Boyyy you the shit💯👣
helpful
Damn bro I was looking all over to get that mount done without taking off the manifold! Life saver!!
You basically just told us how your day was going
This was useless as tits on a rattlesnake
Well did it take care of it?
@@Wigsplits only fixed p2006
Do you have a part number?
04893942AC
Need to know do you have to remove the multiair actuator and heads to replace I'm the shops system for repair procedures had a shop break that and in take valve cause they didn't use the proper tool please if you can respond
Great video thank you
Lol
Very helpful! Thanks!
Awesome video bro, I appreciate your skill and know how, this really helped me out a lot...
Trying to remove the rear alternator belt from 2020 ram 3.6 pickup. Can't release the tensioner
Having the same problem
Hi. Nice video. I am having trouble removing the rear alternator belt. Can you help with which pensioners need to be released and counter clockwise or clockwise direction? Thank you
On the tensioner itself there is a hole for t55 or t60 I can’t remember I hope your not turning the bolt tensioner
God damn liar.. blower motor in the way 2010 ford focus
Thanks for the video man I’m at the shop working on one right now and I did not want to take out the transfer case. Everybody keep telling me to turn the job away but I like the challenge 😂😂😂.
It’s really easy I like challenge too and I don’t tune no money down get that bread 🍞😂
@@ahmadsalim8752 Man so I did it and in the process the starter pig tail got broken 😡 now I can’t put the car back together until Saturday when the new pig tail shows up. The little red tab broke off. The red tab is the part that holds the clip down.
@@atmphil1 sorry to hear that .. how did it happened?
@@ahmadsalim8752 I pulled back on the clip and the tip part of it broke off so I used a small flat head to push the rest of it out from the other side. Installed the new starter when I went to plug it back in it would not hold then I saw there was another piece of plastic that fell out. My store manager at Pepboys ordered the pig tail autozone say it will come in on Saturday. So now the car is stuck there until Saturday. It’s ok tho I have plenty of other diagnostic’s I did that are waiting on parts to come in and new cars come in every day so I have work.
The best way is by removing the battery and battery shield and then you can access to the 2 stater bolts on the side
I didn’t need to , It all depends on the tools your working with
What was the reason you changed the heater car I'm having an issue with only getting heat on the passenger side and I believe it's the heater core which is why I'm here looking at your video
Because car had no heat … in ur case check both heater hoses if one hotter than the other try to flush the heater core before changing it
So if you take the hoses off, it'll slide out? 2008 Ford Focus SES?!? @@ahmadsalim8752
Taking those hoses off was a bitch for me I actually hade just cut mine because it was like welded on my 2019 model at 240,000 miles. Can ask you I have 282,000 on my truck right now and I have been loosing a very small amount of coolant for the last 30,000 to 40,000 miles but the aren’t any leaks that are visible but I can smell a little coolant
I would do a head gasket test
Dude letting all that break fluid run out 😂
Is it the same process if it’s two wheel drive 2018
Very helpful. Thank you for sharing this.
You’re welcome 😉
Make or send a video of the entire process you did.. this seems way too easy
Is a 2006 the same way
Witch motor mount did you unbolt ? Passenger and driver?
Just the passenger top mount
Now Wth u take all that off for smh
I’ll let you know as soon as it comes to my head … it has been a while Thanks for stopping by
So easy to unplug😂😂
Is this the same process for a 2022 Mitsubishi Outlander?
Yes nothing changed
You do not have to discharge the A/C refrigerant... remove the air filter box and you can wiggle the compressor up where the air box sits and lay it there with the lines still attached... i just removed the purge solenoid and a few other simple things out of the way.
skipped the screw removal which is 90% of the work. thumbs down
Ya3teek l 3aafyeh. I needed this video!
Allah y3fek ✌️
That seal fail, bad quality from toyota
Cpol
Great video! I don't have a scan tool and this helps me do the job. 1 question though, my e-brake light on the dash blinks now. Do I have to get it scanned to make that stop?
Check ur fluid level… It shouldn’t blink you might want to check ur work again
Thank you, this video was helpful. I’m replacing my bent axle shaft it causes my vehicle to shake
Very welcome
Did you put the vehicle in service mode
No
Bro you are a savior. The most minimal dissasembly video of them all. I just ordered locking tool from aliexpress, and will do the pump like you did. Ty 🍻
Your welcome 🙏🏼
I forgot to mention You also need a magnetic 10 mil socket they come in a 1/4 for the 3 bolts it helps not to drop the screws in timing cover
@@ahmadsalim8752Thanks for the tip. Have a nice day 👍
Life saver 🫶🫶🫶
Welcome
I believe that’s the Ac compressor you had to move. That big ole compressor
No, it is actually a 24v E-Torque hybrid charging unit and it's Water cooled.
What was your car doing for core to be removed??
Clogged up no heat
But when you accelerated or revved the engine, did the heat work? Or was there no heat only at idle? My situation is that the car will get heat when driving or accelerating but not at idle, thus, causing car to overheat. Thermostat has already been changed. Can you think of any ideas?
I own 11 of these Ford focuses normally when you lose heat at idle and there's a leak somewhere in the system I've had some of them need the upper hose because the quick disconnect area it was seeping or I've also had the water outlets on the block cause that issue that you're describing
Best way to find these leaks is with a pressure tester
Subscribed. I love it when I find a video like this. No intro, no life story, no fluff, just straight to the point with the information I'm looking for. Thanks brotha! I'm going to be doing both sides this weekend on my 16' trd pro.
What tools did you use?t9 and wgg HD at else?
Not really sure u can use a flat head screw driver it doesn’t need much to turn
I would cut a section of that cardboard out the size of your water pump and then just poke holes where the bolts go push the bolts through the cardboard gently and they will hold and draw an arrow for up and then you can pull each bolt out when you need it.
How did you remove the trim?