Відео

Hello there Is there any way to reset factory settings for this controller?

can you explain how to set the VFD YL620-A, please? THX

Hi thanks for sharing with us, I have a question and I hope you read and answer my comment, I have one of this controller, ddcsv4 1 but for same reason I can't make a perfect circle or square I went through everything , no backslash, the configuration on te driver are the right ones before I told was the drivers, replace them same issues, get new kit servo motors and drivers , same issues, I calibrate the steps along the table to be more accurate all perfect, but when it comes to make a circle there is the problem. My cuestion is did you hade the same problem, if is yes did you solved, how? Thanks ho, also I get a second controller and the problem remains, thanks again

I notice you have connections for what looks like Encoders on all of the axes. How is this implemented?

How do you adjust for backlash?

How would you wire 6 stepper motors up. I have 1- X motors, 2-Y motors, 2-Z motors and 1 motor for a Tangential motor

nao consigo conectar nven v5 no pc internete.

parmağı durmuyor sürekli hareket halinde video zor izlensin diye elinden geleni yapmış pezo ayrıca çok kötü ürün aldım pişmanım

Can you tell me more About the ports and pins for spindle speed of the novusun v2 controller?

Which one is "z limit +", and which is "z limit -"? This video seems to only show one swnsor for each axis, and doesn't shpw where the other sensor goes for each axis. And its not clear which is positive and which is negative..

Thank you for posting this. Is there a way to zero the Mach coordinates in the Main Page? I can zero the Abs coordinates by pressing Shift - Zero - choose axis and Enter, but that's only for Abs. All the best.

how to setup nvumv5

okay is the VFD ran independently or can i control the speed with the code i write on fusion 360?

Is this GRBL compatible?

Which microsteps are recommended for queen ant v2?

Will this work with a windows 64 bit operating system? As they just came out with a mach3 64bit version?

Do you know if this will work with windows 64bit? They just came out with a mach3 64bit version.

Не понятно почему в последней прошивке так не работает. Я повторил все твои установки, но у меня неправильно определяется 0 🤷🏻‍♂️🤦🏻

I think you got the error I am getting when you first plugged in the MPG. I get a MPG Hard Reset error, looks like you cleared it with resetting the emergency stop is that correct? My DDCS Expert must have an issue, because I get that error no matter what, even without the MPG plugged in! Does that sound right?

Do you support mach4

What about the other wires that are already connected to the inverter, where they are connected to in other side ??

Can u send this plate set to India . I'm a student trying to build my own cnc . I have over 50+ people accross India but non of them ready to make parts for this and if they did agree they are charging too much . I'm searching online for these plates but haven't found any single seller except u who is selling these . I'll be very thankful if u send me these plates. I'll pay the charges. But i don't know how to import

Hello. What is the biigest custom size can you make?

Good video Guys, looking forward to receiving my QueenAnt PRO V2 Super Enhanced in Australia.

Nice work

I am thinking of buying a 1500x1500 full kit. You recommend your own DDCSv3.1 off-line controller. My question is: does it have USB connectivity to PC for downloading G-code files, as well as remote control fro CNC software?

What software was that you were using?

What is thickness of the spacer?

Good video congratulations Do you know how to configure the index for the mach3 turn? for the same board uc300

What kind of cabling is that called plugged into the side of the control cabinet?

Świetnie to pokazałeś, dzięki 😊

Is there an upgrade kit available to turn v1 into enhanced v2? I haven't assembled my v1 kit yet

I don't see this keyboard control box available. Where can is be purchased? It is available with a 1500x1500 queenant pro v2 kit?

Does the queenant pro v2 support the masso controller?

What are your settings in mach3, like outputs, spindle setup, general config... 😁 Please!!!

How is NVUM V5 controler?

That looks like my Control Box/Panel design (AutoCAD .dmg + BOM Excel files). As agreed I electronically sent attached files to YuYong Industries about 14 months back. My design files also included the mechanical and electrical interface drawings. The only info missing was Phase 3 Setup info. I am still waiting for my side of the agreement to be fulfilled. Contact me for information.

Hi is there any info on how to connect a VNUM CNC controller to my laptop. I have wired it correctly but I cannot get the controller to speak to the laptop. Is there a step by step guide how to connect the ethernet VNUM to the laptop. setup for dummies

Pris 🙏👍❤️

Thats a great addition! Iwonder what is the work flow. Which software are you using? You make a gcode file as well and run it like a milling job? Thanks for an explanation

This new controller looks way bigger than the previous v3.1 one, more features I guess

where can I buy full kit of plates?

Good afternoon, please show the setting of the operation of two stepper motors on the same axis, thank you!

hi there! i just want to ask.. do you guys sell only the mechanical parts..?

how much for the set up as shown?

I bought NVUMV2 4 axis and 6axis also digital dream. try every possible setting it can only turn on the output pin but analog 0-10v not working. I see you put under the spindle output step pin0 direction pin 0 what is that setting for?? I try it did not work is there something i do wrong??

I am setting CNC control using NVCM6V2.1 USB I can't get the spindle to work every time I turn on the spindle it cannot turn off also when I turn on the spindle input 3 also active, it seems like it interferes with the VFD input. the VFD I'm using Etrac XFC2000. VFD input setting Active LOW measuring at the input voltage +13.5v any suggestion? The first time I use this controller it had so many problems. The manual says 12 to 24v but it won't turn on at 18v.

i had a Bellwether yuyong cnc 1500x1500 can i use this upgrade kit

Do we need limit switch on both Y axis motor 1 and motor 2 slave A?

you really need my shop to do a video for you....you should contact me