Відео

had same problem but different bulb socket on a 2022 Mitsubishi. i ended up using an old drum- brake spring tool. not sure i could fit a crescent wrench in

The small incline didn’t effect draining all of the oil out?

Its the regulator at the tank. They have a flow safety in them that if the flow is too fast, they will lock down to just a trickle of gas. You shut the tank valve and let all the gas pressure bleed off, then close the heater valve. SLOWLY open the tank valve to allow the regulator and line to fill and come to a stable pressure, then light the heater and the regulator should flow gas properly… Happens to BbQ and other propane appliances also…

The 5" was too small for my hands...If you do pocket carry I'd go 6"...but the 7.5" is most useful

Is that orange tape on it?...Why?

I have two little holes in my muffler tip in my integra, I saw it leaking water in just trying to find the exact more effective jb weld product

What do you think of the 6 inch? What is the max jaw opening and can you get the padded plastic jaw protectors for the 6 inch?

Toolbox tour??

have you tried using Valvomax or Fumoto?

Bro, thank you…. Definitely not in the same place on many other GM vehicles.

Way way overpriced.

Just replaced mine literally an hour ago. Time consuming but easy to do.

Clean that thing out while you have the cover off.

This Stuff Works !

Hows the gasket holding up???

Is this the actuator for the temperature?

So how do you move it up/down,do you have to loosen the bolts on the side first then turn the middle bolt for up or down or can the it move with the side bolts tightened ?

Whats the oil capacity, I see just a jug of oil and it is supposed to get 5.7qts of oil!

Did you un screw the bolts before you popped it off?

👍👍👍♥️♥️♥️♥️👋👋👋😊😊😊🌹🌹🌹

Is the black finish version as good as this one?

Any update, did you end up installing ?

What is the difference between these and the Cobra's?

Would love to see a follow up video- how do they wear, what are your thoughts after several months of use?

I watched a bunch of these videos. They made it look easy. "Bullcrap". it was the biggest pain in the ass i have ever worked on. I even had the flex ratchet tool. You just can't get your hand back in there to get any leverage. And everything is in the way. Putting back in was even harder took me even longer. Becuase it has to line up right. I also ripped my hands open a bunch of times. This is the worst F**king design i have ever seen. After fighting with just two bolts, I Finally got mine out almost 2 hours later and It was still working fine when i tested it. Good thing too because The new part I bought from amazon for $28 ,Didn't even work. I tested both parts to see if it would work better. Man would i have been pissed. It would have been faster to just take the whole dash out. Becuase that way if actuator isn't broken, it's likely the heater core is plugged. Or its a broken blend door. Either way. At least you can replace any other faulty part right away while dash is all apart. So now i'm doing a rad flush and try to reverse flush the core at the same time. Hopefully that works. If not that means the core is pouched. Then it will be another 4 or 5 hour job.

Yes, it helps. Thank you for the video.

🎯thank you

What year is this?

Ordered some grey 8" forefronts. Can't wait to get them. That grey looks so clean. Have a black pair with safety toe and I love them. Bet the grey ones will look even better.

besides that fuckin bolt on the bottom of the blower motor fuckkk thaaa bolttt omffggg bout shot my brains out

Good job! That’s what I was looking for.

Dude, I appreciate your video. You made it easy

From my experience... All the jb wraps I've used have smoked a bit and stank for a few weeks if not months. (But worked when applied correctly. It's a bandage not a cure.... save up and get the proper flex pipe. You can fix that pipe all you want but without the flex pipe in the exhaust by the engine it will keep breaking no matter what you do... the engine sits in rubber bushings guys, when it starts or you accelerate they squish and the engine moves around in the bay. It stops from vibrating the rest of the vehicles bolts out of everything and makes the ride more comfortable. So the exhaust needs that bendy piece if pipe to keep from snapping the exhaust every time you start it or hit the gas. Be aware that any paste or wrap needs to be rated far over 1000°f if the break is near the engine or behind a catalytic converter (the games react with the metal cat and actually set the fumes back on fire to burn off harmful vapors, it emits less toxins that way ) breaks near or before sensors will ruin your fuel economy and make your engine run dirty by not getting proper air readings to see if the fuel is burning off properly. Hope this helps everyone still keeping the necessity cars running. Exhaust leaks mess up air fuel ratio and it either gets too much air or fuel, both problems wear out and gunk up your internal bits and shorten your cars lifespan.

Looks like Gary on SpongeBob!

😦

Awesome. How do I install the seat now?

Thank you, I’ve ruined my fingers trying to find an anchor inside the seat.. so frustrated! I tried everything, til I desperately went to see if anyone figured it out. Almost gave up if it wasn’t for you! Thank you! Thank you!

Thank you !! I'm doin any moment and have tried several times to figure out the anchor situation. Soo blessed you put this video up 🙏

Does it smoke for a while after??

I didn't know they offered that as a tool set. I do wish the sockets we’re standing up. would save more space in the foam tray like Snap On and icons set up.

McDonald water taste gross

Just bought the same just 4” setback. Hope it works out for you👌🏽

You should really try to do a better job. It really sucked to click on your link and see that you couldn’t even get it to work.

Thanks works perfect for my apartments!! I have a 2018 camry

Aren’t you suppose to wet the surface first?

i got all 3 cobras wrench and twin ! its the last pliers ull ever need !!

Thank you so much! I looked everywhere for the LATCH bars so its not just you. (The manual didn't help anyway)

dumb shit video

My car is giving me a slow flashing orange light when I push it not a green light

Great video. Thanks brother 👍