Відео

How can I get the 3d Print file for the tool you made to put in the caliper piston seals into the caliper!?!? I've been struggling with this and was about to give up until I saw your video. Please let me know. thanks

Where do the leaks typically come from on these components. I have a leak and i cant find where its coming from

Thank you for posting!

Thank you! So hub is slip feet and no shims like rear end. Good to know!

My oil pump fail…the C3 overheat until I exit. At the Bay bridge To Oakland.C3 cool down and drive back San Fco,making that unheard noise next day when I start..now it doesn’t start..I gonna change the oil pump because that GREAT VIDEO…!!! Thanks C3 1978 PACE CAR .

Nice video I learned something thank you

Just FYI. Harbor Freight has a ball joint tool that works better than the fork and hammer method. $20 bits. Takes tie rod ends off easy. Did it yesterday on my C3

It was frustrating watching you, you work way to hard! It can be done so much easier...

I use foaming oveh cleaner on steel parts (not on tolerance sensitive surfaces). it does all the scrubbing and take grease right down to paint or metal.

You did a good job But next time, please place the car on the iron stand , do not leave it on the hydraulic crane For your safety

Excellent 👍

Did you not have to cut the rubber in the supports to fit over the welds?

Jonathan you made that all look pretty effortless. I struggled like crazy doing mine. The foam along the sides was crazy on mine. Not sure if that’s a difference in the year or I just did it wrong. Had to thin mine out to make it go all the way down. Took me an hour to get that lower hose on too 🤣

Great job. Has it held up so far? I did mine and it held great for about 1 year. Now it is seeping a bit. Do you believe I might have to tighten the bolts a bit? Great channel, I am a subscriber.

Great video my friend. Well done. Thank you

You skipped over the hard part, removing the nuts on the door handle.

Love your detailed video! I'm in process of lifting body, I'm in Ottawa. Hope to meet you on the road next year.

Installation tool kit comes with a knurled nut that screws on the adapter and snugged in the center screw, so the adapter doesn’t get stuck in the crankshaft when it comes to removing the tool.Late comment better than never.Good video.By the way you notice the timing mark on pulley always lines up with the crankshaft key.

The easy way of putting on a car cover on the Corvette is you put the front of the cover on first and make sure it's hooked to the front and pull it to the back of the car and make sure you have the antenna hole cut for that so it fits easy over it and just pull down on the cover gently and that you have it with our it coming off

I have a 1977 Corvette it's a prototype it was never ment to be the Father of the Corvette made it it has is autograph all over the car and I got it when I was 16 years old and I still have with very low miles and my uncle was the vice president of GM at that time and my grandpa is related to Louis Chevrolet and the car has everything in it all other Corvettes don't have in there cars

Sooooo no one sees the crack in the frame ?? @7:09 😅😅😅😅😅😅

Way to much talk

Bend those cotter pins over and cut close, they will rip your skin open when you least expect it.

How has the repair held up?

ALways helps to see how someone eLse did it first.. can do both types, but not much room -(Design) for parking brakes.. but.. not for sure. Thanks.

I have to replace the starter myself at this moment is there an exact part number to order the starter from rock Auto? Or just type engine type and model

Thanks Bro. You better wear safety equipment tip to toe as you obviously dont have much experience with saws. One hesitant mistake is all it takes. Cheers

$107 on Amazon for Black Friday

I have a Red 77 C3 just like yours.. I am doing all the same work now, as you did a year ago. I’ll be happy to be a year down the road looking back at all the finished products! 😂 thank you for these videos sir!

any updates on those repaired panels! im trying to do the same to my 87 crx - and want to follow along!

Very good, detailed and instructive video!

Trust me you really need some cool thumbnails your content is good only thing is missing thumbnails.

I’ve got that exact same car… in GTA 5 - FA17 👑

Assembly manual shows installation of pressure hose at pump to be installed 80 deg to the left of vertical so as not to bind when steering wheel turned either direction. Did not see that in this video

its worth it to restore it . they run for ever . i got a 1991 hf 460k still running

I have a 1987 honda civic hatchback im trying to change the fuel pump and fuel filter … i wonder where they located i cant find any video that show or How to fix it can yiu help me out

I have replaced the relay, the contact on the steering wheel and the horn and I get nothin. Any thoughts?

I have a 1984 CRX. This is exactly the video series I need. Did you ever complete part 4? Not finding it on your page.

1st thing is take corvette to scrap yard where it belongs

Go cuse

Another extremely informative video. Thanks. I have to do this for my 1973 corvette, so this really helps.

Awesome video! I love how you show everything.

the first thing that I did with my C3 in Ottawa - New radiator 3 row champion. I love it, in hottest day in traffic no issue. The only problem that I had was the size of the radiator's top inlet. My new hose that has proper size for my thermostat housing neck was too big for new radiator top inlet, maybe thermostat housing not stock. I bought size reducer, put it in radiator inlet and no issue after 2 years. Also drilled 2 small holes in thermostat skirt. Good luck!

You absolutely captured the fun and tedium of this job 😋 👍🏽

hay how are u this is not for this video but thought I could get a quicker response Im working on my 75 corvette and need to do all of my suspension Can I ask u where or who u bought ur parts thru Trying to make this a budget rebuild thanks Tim

This is a wonderful approach, explanation and video. Now I have to do my own on a 2010 Ranger.

Nice! I found 1 near me with only 77,000, very clean. Only problem is it "runs rough" according to the owner. They installed a weber carb, not sure why they didnt keep it stock. Its an 86 crx. Should i buy or pass?

I like your intro the c3 is a awesome car. Thanks