Відео

Useful info, but not a smart work surface.

Do you have a video on replacing the switch?

Thanks for the video 👍

That is why so many pool plumbing parts come with 2 new unions in the box... and that is why you carry a few extra unions on all of your calls.

very good explanation

Really helpful advice. Thanks. Worked following your tips.

Thanks!

Pool heater mini max nt read E04 error code. My pool guy said I need a new heater, fan isn’t spinning at 3000rpm. Found this video ordered capacitor on Amazon for $9.99. Problem solved no more ice cold pool. THANK YOU !!!!!

Can I use my old bearings from my old pump if they r the same exact pumps?

What type of sand paper and grit did you use? Mine is going crazy also will give this a try before buying a new one. If it's going crazy will the salt cell still generate chlorine?

Where did you get the bearings

Finally thank you man appreciate the help

Hi, I'm experiencing a similar issue...where'd you get the small 1.5A mini fuses ? slow blow? hoping you can point me in the right direction. Thanks!!!

Hi there..super late to the party! love your content and had a few questions myself ... recently replaced the keypad/display on a Hayward H400 heater ..the initial problem was no power at all was hoping that this would do the trick but no luck ... do you think I should move on to the fuse board? Thx! oh and are these mini fuses??

What system did you use for the upgrade. Please provide part number. Thanks

I have a error code bd, which board is it typically?everything looks good on both...tia

This is a poor excuse on showing people how to replace brgs u didnt dhow anything about the govenor switch

I got my women power. Gracias Your video was super helpful,I appreciate it.

Which switch does the light usually go on I’m changing the pal lifhr

Thank you!

What is the cost to rebuild one of those ?

Walmart makes a really high quality boots for a very reasonable price

Awesome video dude make more please!!!

BRUH! Thank you SO much for this video! That "screwdriver tap" on the water pressure switch saved me a headache!! Thank YOU!

Do you have another video that shows how you 'repaired' the switch?

If that retaining clip is hard to loosen/corrosion welded to the plate, you can look through one of the air vents on the side and tap the clip with a thin screwdriver. Likewise, when reassembling, you can peek through the vent holes and make sure it isn't blocking the reinsertion of the armature.

I'm not an electrician and I could have done a better job than that 😢 it causes me physical pain to see

Unreal. Mind boggling the guy can’t wire a motor. 😮

Good catch. “Z4” did you say? Never seen one. Why it pays for an experienced ‘2nd opinion’.

Sir! You turned my $200 repair for a new clamp into a $2 repair with washers. 5/8” washers worked great! Thank you, thank you, thank you!

Sir! You turned my $200 repair for a new clamp into a $2 repair with washers. 5/8” washers worked great! Thank you, thank you, thank you!

Sir! You turned my $200 repair for a new clamp into a $2 repair with washers. 5/8” washers worked great! Thank you, thank you, thank you!

Did you do a video of the relay replacement process?

Thanks for the video.

I use the old bearing to sit on top of the new bearing and then bang it on

Thanks bro! Saved me $$$

Thanks for posting this Marcos, I’m currently having this exact issue with one of my customers. However when I replaced the relay I’m still having the same problem. When I go to press the Filter button the relay clicks both on and off but the pump doesn’t turn off. The issue would then have to be the board?

What model is this? Been looking for a video that is similar to mine. My label had been ripped off before I own it. Thank you

The pump used to stay on at certain times but turn off at other times. I would have to go out and turn it off at the breaker. I recently had to replace that pump and since then, the Jandy box inside the house will not turn the pump on or off, but it will turn on the Polaris pool cleaner pump. I am wondering if that too is a relay switch gone bad. I have a whipserflow pump not working as well and I think that is for the additional water flow for the spa as it does not shoot out water from it's jets as it used too, only about half strength. Also the Pool Pilot Digital display is not working at all, just blank screen and the salt chlorinator is not working, probably as a result. I have some work to do on this pool. What advice can you give me about the switch and digital display?

SUPER INFORMATIVE! Thank you for exposing and showing you were able to eliminate the board from the issue.

Besides the pressure switch, do i need a flow switch if installing a bypasss valve? If using the bypass, there can still be pressure even tho no water is running through it. Its a raypak 8450

Hi Marcos, I wanted to ask, we currently have an old aqualink rs4 controller that currently isn’t turning off our pump? We were told that it may be a relay problem? Are you familiar with this system?

Hey Brother i was wondering if you could help me out. I recently replaced a pool cleaner pump thinking it was broken since it wouldn’t turn on. But when I put the new pump on and turned it on, it still wouldn’t turn on even after canceling the delay. It sounds like it wants to kick on but only for a split second then shuts off. Do you think the relay the issue? I’ve replaced a few pumps now and this has never been a problem, The pump is wired properly and is getting 120V on each terminal when I put the volt meter on, so I’m not sure what to do anymore 😢

Yeah that's what I'm talking about

Great video Marcos. You ever seen where pool motor has correct 230 volts but the minute you turn the filter pump on on the control board it kicks out the 2 pole Seimens breaker? changed out the pump thinking it was the pump and still doing the exact same thing.

Thanks Marcos

Thank you so much for this video. Amazing.

right on

The first one is a air pressure