Відео

Sir please how can I get a white and black terrain like this , I don't know why my own is always completely Green which make my road (corridor) unreal it will just be lines, it is not real as this in the videos 🙏🙏🙏

Nice

Hello, where can I download the extension?

Hello Mr. John, excellent video, thank you very much for sharing it. I have a question, when you configure the time of concentration for the post development you only configure the sheet flow and the shallow concentrated flow but you do not consider the 5 minutes of channeled flow from the road to reach the pond, the total time shown in the tab The report is 12.64 but you do not consider the 5 minutes of channeled flow, is it something you forget or is it not really considered? Thanks in advance

Can I have sample file of this project?

you should come to algeria to show us how to update size pipes

I sent you the file to your email address just check in your email address

hey john did you find the solution ???????????????????????? I told you it doesn't work

how can i send my file? you should give your email

hey john forget about it anyway it doesn't work

Really great but I wish the pond outflow had options like Hydraflow extension where you can make adjustments and see in real time the outflow conditions for each storm event

anyway I follow the same steps but it seems it doesn't work

hey john let it down I mean I tryed one hundred times but in doesn't work

I follow the same steps you did, but it seems it doesn't work with my civil 3d 2016

hey john, I don't manage to update size pipe and yet I follow same steps

Whenever I try to update size pipes all manholes delete automatically on civil 3d 2016

it doesn't work, when I try to update new size pipe I lose manhole on civil 3d 2016

Thank you for this great video just have the following question concerning the sub base entry why the average was checked instead of the weighted average (area percent ) or one of the of the other options thank you again

I can't make it work to have two orifice. It has that drainage system has no acceptable outfall nodes and outfall xxx has more than 1 inlet.

where is Storm and Sanutary Analysis module in version 2024?

HELLO , I WOULD LIKE TO HAVE THIS TOOLS , HOW CAN I GET IT

Hi Sir thank you very much for this very informative video. Sir, where to get that extensions for bridge both civil 3D and Revit please?

Great

dear john thanks for efforts & great explanation, could you plz share the csv file called "timeline", thanks Boss

Thanks for the video. I realize this is an older video but thought maybe it could help you to tell you a mistake I have made with conversions imperial/metric and state plane. Be careful with your imperial to metric conversion. using .3048 you're using international foot conversion not US foot or survey foot. on small numbers it doesn't make much difference but large numbers like state plane coordinates it makes big differences. Here in Oklahoma it makes about a 4 foot difference. lesson learned the hard way

very good we will be so greatfull if you can revise it version 2023 Civil 3D

Can you please explain the design of the vertical pipe using SSA?

Should we design sewer and storm drainage separately or jointly using SSA and hydraflow?

After setting up SSA and run the analysis, I get the error message "INF is not a valid floating point number." Any idea how to fix this problem? Thank you.

Video for putting your own softs on or is that possible. I can softbox so would like to up load my own softs.

Once I Get In The Top Ten s Your My Credit ;)

TNice tutorialS WAS SOOOOOO HELPFUL!!

.

Good information, do you created any Technology based Civil 3d video, Like Electrical power cabinet, Electrical Duct & 3D asset tagging. Please upload if you have , thanks @john Sayre

Hi John, Thank you for the video. Is there any way to design for the 1:200 year storm event using the rainfall designer? I noticed that it ends on 1:100 and I would like to analyse other return periods.

Anyone know how do you reverse flow direction in version 13.4.133.0?

Great video. What was your simulation period and how did you select it

excellent

Great video! Thanks

Sir, how to do you solve bowties in curb returns for intersections? I am new to Civil 3d.

godlike sharing, thanks!

Hello John, where can you get the IDF curve table files?

This tutorial is explained very well and explains everything step by step! Thank you so much for making this tutorial! It has been extremely helpful!

can you submit the drawing for practicing?

Hi John, is there an email I can contact you on in regards to some VR questions I have. Thanks Jason

Hi John, Please how did you get your external flow to be 3 CFS? Did you get it from the run-off discharge? Which rainfall return period did you use? Thank you.

So, what is the setup for an infiltration pond design? Also, how can you obtain the treatment flows?

Hi there nice informative video. I am struggling to edit projection and crossing of solids in my sections. how to turn them off together for whole section groups ?

Great video, can I have the retaining wall sub-assembly

what a great video. Thanks Sir!!