Відео

This isn’t totally the wrong way to do. If you put some barb fittings on the insert and run hoses from the fittings to a bottle of brake fluid. Once you see a solid amount of brake fluid coming out of the clear lines it’s done. Make sure you’re doing this and the hoses running down like gravity bleeding.

You stupid...somebody gonna believe this and have a crash..... please take this video down.....

You can't remove all the air from a dry master cylinder without cycling the piston. If the fluid could move past the seals and displace the air, then the seals wouldn't be able to trap the fluid and build pressure during normal operation.

Thank you!!!!! I’m 64,had to do exact same thing to wife’s rogue. Sockets were all right on and very informative. Wife happy,now I get my pickle tickle tonight👍

I have the same issue right now 😢😮

this person does not know what they doing !!!

What’s that’s part number?

This how to wreck your car😢, goof ball dont know nothing

Same for a 2018?

Dropped fluids there in the car, is insane,, damaged parts ,, 😢

Excellent video! I was hesitant to meet with that strut until I watched the video. Design could be better, but doable.

Gotta push the piston in several times to finish getting the air out

Scotty Kilmer shows similar method..!

Bro didn't even bother cleaning anything....straight work van. LOL Just a note, don't ever spray your caliper with PB Blaster. The oil products will seep into the brake fluid and ruin your whole brake system. Once you get petroleum product into the brake fluid, it swells the rubber seals everywhere. You will know your brake fluid is contaminated when you pull some out and put it into a glass. The oil and brake fluid will separate into two layers that you can easily see. Also I don't think you used enough grease............ sheesh

I'm sorry, but that's hardly a "mechanic's setup". Looks more like a van with a compressor and a bit of storage.

U sound like EST G 😂

Brake caliper hanging like that is not good who taught your a.. how to work on a car....d a

How do you troubleshoot/diagnose the master cylinder being bad/good?

Solo tienes desconectado un cable de tierra que va al reley,del lado del pasajero.

Haha that’s the ghetto bleed .😂

I don't see any issue with this, don't know what people are on about. Any air is right there at the top, it'll travel to the reservoir immediately. If people are concerned about that tiny bit of not-trapped air, I'd like to show them how much air is actually in the rest of their system, and how much of it is trapped in joints and parts that they'll never get out with regular bleeding. reverse flush is king imo, one man job with a $3 500ml syringe.

Bench bleed the damn thing. Brake fluid is going to eat that paint.

Hmmm🤔

Thanks!

I dont see why it wouldn't work. After i bench bleed them you have to pull the bleed tubes of anyway. I just dont drip fluids on my nice paint job but if its a beater who cares just throw water over it.

Bro you missed some steps

Thanks

Thanks !

My brother told me, maybe my thermostat cause the issues.. so I bought thermostat n have it ready for my mobile mechanic guy… he asked me to get the thermostat housing, since the new one didn’t have the seal…. I do what he asked , so I went n got the thermostat housing…after he replace it … car run for 5min my needle point to hot again 😩and the car won’t start .. what could happen can you think of?

Got his money's worth.😂😂😂

Bro indid my sister in laws Santa fa and her rear rotors complete separated the pad parts came off the hub. They was done. It was both sides too and her front were no bite left. And she's didn't think she needed brakes I just happen to see then like wtf is this shif!!

I have 2016.. u think it locate in same place ?

I have a Cummins x15 with the same issue, do you think the repair is similar to this dd15?

I'm giving it a try right now. At this point nothing could hurt my car

Isn’t brake fluid highly corrosive

This guy don't no nuttin about bleeding the master cylinder don't pay attention to this guy 👎

Torque specs when putting the bolts back in?

Bien bien

Soot is causing it to turn black does that have anything to do with ERG

*Maaan whatever that roll is for the thermostat was a life saver. Got it on and didn’t have to take the extra hoes off*

Mines is not going down at all it bubbled up one time and im still pumping it after i changed both the fuel water separator filter and fuel filters. The prime is working but its not going down

🙏🏿❤️thank you brother

🤦‍♀️🤦‍♀️🤦‍♀️🤦‍♀️

Don't listen to this guy he is absolutely wrong

Broooo nooooooooo!!!!!!! Don’t listen to this goofball

FYI…With ABS systems it’s better to collapse the pucks by loosening the bleed screw to prevent damage to ABS system and also gets rid of the bad brake fluid that has been close to the high heat! Nice video!

Using the tube in the box that looks like a toilet paper roll is the best and fastest way to compress the thermostat.

I swear Chevy intentionally makes everything hard to get to. This will be the first and last Chevy I buy.

Leave that man alone man. He driving a Saturn cut him some slack

W-o-r-s-t. Worst. If you can't spell, ask somebody who can. You will get more views if you do not distract viewers with mistakes in spelling and grammar.