Відео

Hello. Sure, for extra saftey you can disconnect the battery. But if you are carefull there is no need.

Hello, it's just because I don't want to keep my foot on the brake all the time :) I put it in Neutral so i can relax :D. If the road has an angle to it, then I keep my foot on the brake or use the Auto Hold feature if I am feeling lazy :D

Activate the Auto-Hold function before every ride and you don't have to shift to N :)

Happy to hear it workd and the video was helpfull for you :)

Hello, it shouldn't be a problem if when chaging the HID bulbs you don't pull too hard or be to agressive when installing the bulb. But if you are not comfortable with the work I recommend going to a shop / mechanic.

Hi, unfortunatley I do not have access to a CX-90, but the removal of the B billar trim should be the same as in the instructions. Just remove the weather stripping, look for any covers that would cover a screw to remove the screws and the gently pull on the plastic trim.

I guess you can, yes. If you manage to keep it in place.

​@@DCHero15 Okay, thanks!

​@@DCHero15 Is it safe to put foam tape under the Airbag clip?

I would think so. As long as the round airbag clip is securely in place in the A pillar. Or are you referring to the one at the top near the headliner ? (I just put a small piece of foam tape to stop that small movement. The clip is still securely inserted in place)

Glad to hear it helped :D

Salut, sunt foarte multumit de ea si dotariile ei :) Nu am avut nici-o problema cu ea :D totul merge ok :D

Ma bucur sa aud asta, sa te tina tot asa! :D Cum e viata prin Timisoara cu ea, fiind mai rigida si destul de joasa? Ai avut ceva probleme la parcari? Intreb ca si eu sunt tot din Timisoara :D

Hello, yes. It's very easy to handle as a beginner and its easy to ride it :)

@DCHero15 Thanks so much!

Thank you

I am going to buy a large piece of foam and I will fill the entire dashboard with foam, hopefully it works

Is the rattle still coming from the speaker grill ? If yes, the apply some Tessa tape tot the metal clips of the speaker housing that go in the dashboard, so the clips are held better in place. Also if the rattle is coming from inside the dashboard, there are some computer modules that tend to vibrate / rattle, also under the passenger airbag as well.

I bought it from the local hardware store. It’s a foam insulating tape for outdoor water pipes. I’m sure your Home Depot / other brand store of local hardware would have something similar. The diameter I say would be 5 mm (height) and 2 cm width. Hope it helps

Glad the video helped you out

For other problems that I cannot fix myself, yes I go to the dealer. On the other hand I like to fix things 😂 so the problems I can solve I would like to try and do them

Hello, yes I do recommend it. It’s a good car and good value for money. Interior quality is very good and good looking and the exterior as well. Currently I have no problems with it, all works good with no problems.

NFS old school

Thanks 😄

The way Daytona recommends to wire the heated grips in the installation manual is via the ignition wire. (Accessory power) That means they will receive power only when the motorcycle is switched on and turn off when the bike is off. I guess you could wire them via a relay if you want to 🤷🏻‍♂️. I just followed their recommendation from the installation manual. 🤓

I plan to get a Ninja 1000SX myself, to replace my CBR650R sometime in the future.

Hey there, glad the video helped you out. I posted the video on some reddit groups and some facebook groups as well. If you have any reddit groups dedicated to Mazda 3 please go ahead and share the video :) Thanks for the support :D

Glad the video helped you out.

Good to know I could help 🙂

Hello, it is D4S

@@DCHero15 thanks for the video, managed get it done. My AFS was blinking after change the change, do u know what's the issue?

I don’t really know what could have been the issue. Did you in any way move the mechanism of the light bulb when changing the light ? The model I worked on did not have AFS. Perhaps the car needs a calibration to get clear of the AFS. A OBD2 diagnostic could help in this case.

off and on the AFS button, then AFS light is gone. But when i tested turning the steering wheel, AFS is not functioning. Need to relook into the installation if I've move the mechanism.

Hmm hard to tell. In my case I had a bolt that was not tightened properly. The bolt in question was the one that holds the interior hvac fan, located under the glove box. The bottom bolt under the passenger floor carpet.

@@DCHero15 I will check that. This comes from HUD / instrument part of dash. Dealer can’t hear 😭 I will find it. And I will fix it. 💪🕵️‍♂️

@@ryanmclean2658 ​​⁠ for the HUD rattle / noise there is a service bulletin from Mazda regarding that. Models before 2021 I think are affected. You should check with the dealer

Thanks!!!!

Hello, My 2021 model year does not have any rattle / noise coming from the HUD. However older models I think have that problem. There is a service bulletin out regarding that issue. To fix that rattle, foam is needed to be inserted on the areas that vibrate. Hope this helps.

​@@DCHero15 Thank you! I'll go to the dealer for explanations✌

I installed Oxford Heated Grips on a Kawasaki Vulcan S, 2 years ago. They are still doing their job quite well. No complaints with them. The Daytona is a first. Build quality seems much better than the ones from Oxford. The design is much sleeker, with the power on button and mode selection hidden on the left grip. Yes, they get toasty hot :D No complaints so far with them. If you want to buy them, go ahead. You won’t go wrong 😊

You can find them on Mazda’s website from the region you are from. There should be a section dedicated to accessories.

In the summertime yes, it would get a bit toasty 😂. The video was filmed in October, when it wasn’t that hot outside. It was around 20 degrees Celsius that day (68 Fahrenheit)

Thank you for the support. I also have a short UA-cam video for the B pillar rattle that you can check out

@@DCHero15 Good to know. Thanks a lot...

Thank you for the support !

Yes, correct. I should have done that, but I decided to follow the instruction manual that came with the kit. Next time I install parking sensors on a same model year mazda 3 I will do so, and drill in the pre marked holes :)

No, it’s in Romania.

The Z900 is much better, yes :D

Glad it was helpful! Thank you for the support 🙂

Do you have any suggestions of a song / music ?

?

Why the thumbs down ? 🥲

Hi, it’s a 2021 model year. Hatchback for the European market.

Hello, I have bought the parking assist kit directly from a mazda dealer. I don’t know if you can find them outside of a Mazda dealer. Go to your Mazda dealer and try to see with them if they can provide the parts for you

I don’t know what that is. What is that ?

That’s correct. Good eye 😉 The suspension on the bike is not that good, the front end feels weird. My CBR650 feels much more stable and the front end feels more planted on the ground.

Hello, if you click on the video description, I made a PDF explaining how to take the B Pillar plastics off.

B Pillar removal instroctions can be found here: drive.google.com/file/d/18qMoy9_OIVgPHPRkVrO0X8AlfRyaHvPW/view?usp=sharing

just ignore point 1 because u dont want to change the belt.. you just want to lose the cover slide it down between seat and lower B-Piller so you have access to the points shown in the video :)

Hello! Yes, you can use the video in your compilation

@@DCHero15 thanks !

Hello. Yes, you can use it. Go ahead

@@DCHero15 Thanks

Hello, yes go ahead. You can use it

Hey, as long as you don't get near the bears or try to give them food it shoud be ok. Just keep your distance. Since you will be traveling by bicycle, I recommend you have some anti bear spray with you just in case to be safe.

I agree!

so do i

yes, its a pretty cool little scooter. Where are you from ?

Da, putea putin sa traga de volan. Dar asta e... daca am loc ma bag. daca nu stau si astept. Oricum tot o sa ajung la un moment dat inaintea masinii respective :D