Відео

Rule #1: Manufacturers of high-end audio and video electronics _do not_ put pretty pictures on the outside of the box to try to sell it to you. When bought from a legitimate retail outlet, by the time you see the box, you have already purchased it.

Where did you get your pump and how much it cost and do you get any type of guarantee on it or what’s the best place to get it at?

He is actually the narssict what he does is record after he cause her to go crazy and he plays like he's the victim

This is just talking. He does not show the viewer where the orifice is located in the liquid line.

What was the motive behind this design by Honda if there is one?

That is a lot of trash in the oriface tube. If you dont flush out that system with cleaner and properly service it, youll be doing this all over again, and most compressors youll void the warranty if you do not flush and clean the system. I bet that whole system is still caked with that junk. Youll probably be replacing the evaporator, and condenser.

Don’t do that in front of the kids

I know he hurt but he need to stop saying all that stuff in front of there kids

He acting like a woman

Lol

Why is she going to jail

Why is she going to jail

This is exhausting

Sang lt Cuzin

sounds similar to the B737 MAX8 i dont know why

This mfkr got security shirt on .....the streets need to fire him

Thanks for the help G I’m fixing my moms car

🤩Amazing....congratulations 🎊

Did it ever get fixed and or rented?

❤

Dude whoever has the camera is fucking annoying you're saying the same shit over and over and over just shut the fuck up

Might change this on my A8L tomorrow. Air is only getting cold when idling and it was just freezing up my hands and the windshield

Dollar store mechanic

Them teeth😬😬

Make sure to decharge aka relieve the pressure of system before you crack that line or you’ll get sprayed in the face with ac dye, a friend of mine did this. I found it hilarious he however did not 😂

I just took one out of an f350 the exact same way. It was facing the same way with the long side in which I believe is backwards. The long end of the screen was bent over at the tip from trying to follow the bend in the tube which I believe made the flow worse. I personally have always put the in short end first.

Is the whole subframe and dismantling everything consistent with the 08’s? Or did they make it easier?

Sorry, but it's obvious he's the Narc

Thanks For the video and Information Learn Something Every Day.

Congratulations 🎉

I don't believe it was her cousin..it was just one of her many foul shady no good lies.....and both of those fools deserve what they get..her supposed cousin and her both!!!

I don't believe it was her cousin..it was just one of her many foul shady no good lies.....and both of those fools deserve what they get..her supposed cousin and her both!!!

I would have sat all that on the curb....she foul and shady as hell....I went through the exact same thing!!

Nice Views.

A highly knowledgeable guy at NAPA said i needed to flush the system. They sell the "flush". You have to use an air compressor to push it through. Disconnect the lines from the compressor first and have a catch tub

😂😂😂

So mine is just as dirty and greasy as that one or maybe even a little more. The line it goes in is actually the bottom line going into the evaporator. Don't you think with it being that dirty and clogged that the evaporator would be clogged also?

Black men will sleep with anything

I swear she shady as hell...she standing there and can't explain her low down dirty actions!!!!

I swear she shady as hell...she standing there and can't explain her low down dirty actions!!!!

really shut up and go in ur house

Helpful. Thank you

When are u gonna get ur teeth fixed?

Yo thx for this video, best by far showing the prices an stuff ...

That bitch was sorry asf and all the people watching it were too. It’s called being human don’t watch stuff like this happen they should all be put in jail.

There is a much easier and much less invasive way to do it. Just drill a hole through both sides of the "C" shaped metal brace, in line with the screw head and just big enough to fit the 5.5mm socket through. Once the screws (all 3) are out, you can just use a little leverage to slightly bend the metal brace to make enough room to get the actuator out. You don't actually need to bend the metal, just push it enough to flex it out of the way

Even if I can`t get the actuator working , watching this , looks like I can turn it by hand with or without the actuator in the way , by just reaching in and turn it . Thank you . Well Done .

C'mon, man... tie that brake caliper up! Don't let it hang by the brake line!

Poor kids having to live in this nightmare. My heart is breaking for them. I pray they have peace in their lives now.

This guy is weird trying to belittle her and to try and show her meds Bitter Bill