Відео

Wow exactly what I didn't need. Who's having trouble putting it in? I'm having an issue taking the thing off.

@peter tec I need help mines is a 2006 and it doesn't have yellow and orange wire it's yellow and black is that's the right wire

Good job !!!! You're mad smart for that !!! 😎😎

I just bought a 2006 pt cruiser gt with only 46, 000 miles dude said it was fine but after a drove it home has a p0700 with a p0882 low voltage code an stuck in limp mode a bought two pcms an 3 fuse box fuse boxes off eBay were worngs ones an no shop can figure it out but i think this it man i just gotta figure out how u did this im been tring to figure it out for a year 😮 wish your were near me bought the car for five grand an i but five more into it an it still just sets there so sad im waching this all day to understand this lol ty

How much does labor cost for this

Next time use a chisel to separate the strut clamp and will slide out easier

I can't get the lower control arm to drop down far enough what is the trick

how about alignment issues after you install?

Excellent video. The beam attached to the alternator is only for support on the engine/transmission.? You did not lift it from this support beam ? It just allows the support as you remove the engine mount bolts and allows the pan room to drop.. I will watch the video again since I have debris from the chain guides. Aluminum and plastic materials are in the pan and mostly likely the pickup screen which must be cleaned. How difficult is it to put the pickup bolts back in. I am going to change the oil pump since it has 147,000 miles and aluminum pieces/ grindings which are not filtered pass thru the oil screen . The oil pump receives unfiltered oil from pickup. Thank you

Thanks for the information.

I got a 2006 buck they say that I need a fuel pump sensor is that the same as the Gage

Hi Peter! Where can i find you? You are in DMV area?

not even the passenger side.

thank you,gracias, gratze, mucho bueno amigo

Would you show how you raised engine how high did you raise the engine and did you remove radiator and condenser I need to change my oil pan gasket on 2002 Lincoln towncar badly

Is it necessary to suspend engine to keep it from moving?

Another amazing video!

The friend wanted in the shot, maybe he's trying to get his SAG card?🙂

How do you take off the axel shaft bearing and put it on the new replacement axel

How hard was it to remove the shaft from the transmission? What tool did you use?

How much will be the cost for this job

Why you got to leave the fucking door open and leave that alarm ringing throughout the whole fucking video I can't even hear you because of that that's all I can focus on because it annoys me just as much on TV as it does in real life

OMG 😲 .... you need to change the oil pan only: 1- Remove 2 bolts 🔩 engine mounts 2- Jack up transmission body, remove oil pan . that's it

Can you call me

How you that nut out, the one you right on bottom.

Is the fuel pump still working I just bought a 99 regal same problem but don't want to replace the whole unit just the level sensor

Almost 50! Subs bro!!! 🙌🏿🙌🏿🙌🏿🙌🏿

Question is why are these failing so fast? Ford had turned to junk the last decade or so.

How to fix gas gauge on Buick LeSabre 02’??

Put a description of what you did bro 💪🏿

What year ram?

Best videos on UA-cam

🔥🔥🔥

My favorite place!!!!

Was the strut easy (easier) to remove from the knuckle with the whole thing out like that? Thank you.

Did you have to drop the tank

But what's the easy way of getting the strut assembly out (and the replacement back in) the wheel hub? I bet that's a lot of hammering!

Question: I have a Buick Lucerne with the Fuel Gauge staying between 1/4 & 3/4, it doesn't go to Full or Empty. Is the Problem a bad Fuel Gauge Sending unit? Thanks.👍

If your going to go thru this replaces the whole pump with everything new as an assembly

I have a 2008 Lucerne. Fuel gauge not working and showing a check engine light because of the fuel gauge. Replaced the fuel pump but gauge continues not to read

My 2001 buick lesabre gas gauge reads full all the time when running but goes to empty when off