Відео

This is the second time i wach this video to learn how clean my carb and i glad to have found it thanks for the time you spend to do it🫡

How many pulls before it started up? I am having issues of hard to start.

It's always the carb!!! (unless some kid got a hold of it and ran pure gas, not mix like my idiot half brother does to chainsaws. I just rebuilt my 8hp carb, a gen before this one you have. The rebuild kit off Amazon for $20 did not have a sufficient bowl gasket so I made one from 1mm silicon. I noticed the main carb mount lower nut was so loose I could spin it off with my hand because that gasket had shrunk. If I'd have just tightened those nuts it probably would have run just fine but, in for a penny, in for a pound. I posted a video on making gaskets. Hey PS: replace the zip ties (plastic) with teflon ones as soon as you can. The plastic will get brittle fast and suddenly pop

🫨😮‍💨🫨😮‍💨🫨😮‍💨🫨😮‍💨🫨😮‍💨🫨😮‍💨 is all I heard

CRAP VIDEO MOVING SPORATICALLY ALL OVER POOR LIGHT!!!!

Ur breathing is kinda hurting my ears and brain lol hard to watch

Im having a starting issue with my 95 mercury 2 stroke 9.9. I clean and rebuild my carb but after start in a few minute then engine died. Any suggestion will help. Thanks!

Did my carb on my mercury 9.9 97 model. But now every time i try to pull it to start it sound like its about to fire but only goes boom every time. Some tips?

You are always moving & holding your camera up so you can’t really see what you are doing and talking about…

I know this is an older posting but i had never had the carb off my motor so I went to UA-cam for help , and wow great video sir made the job so simple . I too couldn’t get the main jet out of the bowl it was as if it was galled in there , one other note , mine did have a gasket between the carb and head . Thanks a lot for the great video , saved me some money

great video! i bought a older boat from a fella had a 1999 9.9m on it did the same thing as this.i followed your video and now, mine is running like a top! thanks

Pull the 3 10mm bolts that hold the pull cord case and it's 100% easier to get access to the carb

cheddar bay biscuits???????

Is there a drain on the carb I need to drain mine for the winter

I’m having the same issues with my 87 mercury 9.9 and I’ve had the carburetor rebuilt. But the float valve keeps sticking

Thanks for the video. I picked up this exact motor this summer. It is hard to start and will not restart when hot. There have been many issues that I have found and fixed. Dirty and corroded grounds, coils missing ground jumper wire, emergency stop switch wires rubbed through causing a short to ground, and the stop switch on the tiller handle was defective. It still does not want to start. One plug is fouled, both have spark. The carb leaks fuel when choke is on and you turn it over. The carb was supposedly rebuilt and the engine was "inspected" this spring right before I bought it. I hope both cylinders have compression. This video has been beyond helpful, thank you.

Great video. If all that junk (amazing!) came from an old fuel line, is there no fuel filter? This was really well done and very helpful. Thanks.

Thx for video. I got the same motor. Is there suppose to be a gasket between the carb and the engine block? My carb rebuild kit comes with a gasket. The Mere Parts diagram also shows a gasket. Mine didn't have a gasket from previous owner. Perhaps that's why the motor ran funny. In your video, I didn't see a gasket either. The mating face on the engine block side has like a rubber seal around the openings. Any help would be great.

Thanks for doing that video. Now I know what to expect .

Cracks be up when people say theres no quality fish in lake Arthur lol.. me & the ol lady was catching 10" /15" crappies consistently

Thanks for the very helpful video! I just picked up a 9.9 and first day on the water it started bogging down at WOT and eventually would barely idle. Upon checking out the motor, I noticed the previous owner removed the fuel filter from it's housing, and I'm betting my carb is full of shit. This certainly comes in handy since I have never worked on a carb motor at all, nevermind a 2 stroke.

What oil mix do you run I have the same motor

Nice build. Think it came out pretty sweet

Lake authur frozen yet this year? Probably not huh?

Nice fishing video👍Music is also cool！！ I'm watching from Japan, I am also an angler I want to be a video friend🤝

This video got me so pumped up for Ice Fishing!! oh.....love your channel name!! ha ha

Just had to do that with mine. Good job!

I love crappie and ice fishing! New SUB brother, hope to catch you back on our battle to 1000 subs

Thanks for the video 👍🏻 Carb is the same on my 95’ Mercury 25 hp. the only thing I had to do different is remove the starter to remove the inside carb mounting nut. I purchased a rebuild kit first $20 ( gaskets, plunger ect. ) followed your video on disassemble and cleaning, the issue was the float was full of fuel, purchased a new float $11 re assembled and BAM RUNS LIKE A MERCURY SHOULD 👍🏻🇺🇸

Thanks so much for this video! Absolute life saver.

Thanks but you could have the camera where we can see half of what your doing

Is there a way to rev these small 2 stroke outboards in neutral? I have the 20hp and i have to clean/rebuild my carb. But i was wondering if there was a way to slightly rev the engine before I decide to put it in the water

Thank you very much! I'm having a problem with the bar you lock at minute 24.30. I don't see where to attach it to the other side. With you it is also loose in the video on that other side, but suddenly it is stuck as it should. Can you please help me?

Cheers mate. This is the same as early mariner outboard in Australia 👍

I have the same motor as a kicker on my boat. When placing the idle adjustment screw back into the carb, what I did was mounted the carb loosely and then placed the "C" part that goes on the adjustment knob together, placed it thru the hole in the cowling. There was no amount of pushing needed to get it to go as Crappie says. Once that was in, go the the left side of the motor (when you are behind the prop), press down the lever Crappie tells you when he is installing the knob. You will see how those two parts clip together, it is pretty obvious. This might help you. Awesome video!

Thank you so much for this video!!!! I’m a boater and enjoy learning about motors since I’m out on the water a lot! I can’t find a serial number for this new to me merc but it’s a 9.9 2 stroke and carb looks exactly like yours with fuel enrichment and all. I rebuilt my carburetor (it had some water and jelly like stuff in there) and still can’t get it running right. It starts if I spray a gas/oil mix directly into carb but idles way too high and then stalls unless I manually open the Choke butterfly. I’m ready to break down and buy a new carb. Any advice??? Would’ve bought a new carb instead of rebuild kit if I had opened carb first!

I hope mine is the carb too... my 25 hp doesnt idle. But i can still use it as long as its moving forward.. and it starts to bog when the fuel tank is low.,.. motor looks exactly like urs but 25hp.

Thank you very much for the taking your time making this video helping people's, you definitely save me some $$$$$

You should affiliate market the lures you’re using. Good info and fishin’!

What lure/bait were yinz using?

Sweet vid man! I’ve been wanting some pike through the ice so bad. I need to go explore some new water.

Bad ass video my man!

Go get them Joe

Anyway you could help me with CDI wiring I have a new cdi box and I'm not sure on which of the two black wires goes to trigger/killswitch.

I need your help badly. On the enrichment assembly was there a pin that goes across the whole assembly?

just did one of these you could have left all the plastics on the motor and just removed the 2 small bolts my motor was sunk so i was draining water good job

ive bin pulling cranks too in va helps me find the fish

Like always. Nice job Joe. Very nicely put together video.Glad to see you using planer boards on Crappie. On of my favorite ways to fish.

Just a note for all ! I stuffed a rag under those areas in case any hardware fell it wouldn’t go under the engine and making it hard to get out.

I just did this on my 1999 20 hp Mercury, after watching the video I decided to check mine. This all stated with hard starts and then eventually no start. I found the ignition system to be finally dying. After all the repairs it still had carb issues also, the primer was stuck and wouldn’t depress when pulling the primer knob. Also I removed all the cover plates and bowl cleaned all the internal passages. I found your video very helpful the engines although different horse power they are identically built. Only issue after that was the switch box wiring was a shot in the dark for firing order. I missed it. Once that was correct it starts first pull now every time. Hope this helps others along with your help on the repair. Thanks