Відео

I have a struggle during working with PF527, it seem that my drive was configured in Network Safe Torque Off and i cannot changed it to hardwired or disable Network Safety. Do you have any experiences in this case?

what kind of comunication is DSI? please, look like Canbus, rs485, confuse them.

Do not tell you no details to how to troubleshoot with each parameter category or number it's just a video that says these parameters exist.

Short and to the point!!.wish more videos were like this one...excellent..😊

Thumbs down much too fast for the layperson, no details just moving through too fast.

Terrible details in which a lay person cannot follow.

I need help communicate with dsi Thanks

Finally a clear explaination

Excelente video,una consulta puede migrar pantallas de un hmi panel view plu 6 a scada factory talk view,para hacerlo funcionar.

Excellent!! Thank you

You should do more of these

Quinn's Wins is back!!!

Thanks for the video!

Please how to contact you ?

Thanks a lot for this Sir.

beautiful

Nice video!!

I’m registering an SS 09 fault. Can I disable that monitoring feature without using the computer?

What do you do if you get data factory fault or initialization fault on kinetic 5700? Thanks boo

Thanks, good job

Hey, Thank you for your videos, its hard to find videos on the subject (probably not enough keywords, and i'm frensh it don't help) I'm noob in Allen Bradley devices. How do you know wich port is attached to ethernet ? I Have a PowerFlex 755 ENTE, with Safe Torque Off and 2262C-2R I/O cardes I want to control the VFD in V/F mode (to drive a pump) with i/O in 2 Wire Mode and HOA Mode ; in Hand mode fixe the speed througt VFD-HMI and in Auto Througt Ethernet. Is there a way to do that (my HOA commut. is wired directly to the VFD inputs througt "NO" contacts (not like your methode wich is an 3 Wire equivalente one). I have dificulties with AB Docuementation wich is realy ambiguse (what is the difference between "155-DI Actv", "161-Sart ED", "163-RUN ED" . At the Feeling I should Link : - Hand input to param 163 - Auto Input to param 174 - Hand Input to param 172 but no Idea on witch port linked to Ethenet/IP Exchange Table Nither to the way to acces a data from the Pocket. For information I will get the pocket on half-January 2024 (1 year delay !!!), actually i am programming my VFD througt Connected Component Workbench. I arrive to commande the VFD Throug Ethernet\IP. I descovered that my 2262C I/O card should work correctly only if installed on port 7 (the outputs worked well, but the inputs didn't worked insted). I Think I Have my answer thanks to : "How to Program an Allen-Bradley PowerFlex 753 Drive" video. - Default port for HMI is port 1 so I have to put 871 in param 545 (witch is default value) - For the Ethernet port, I have it in my config witch 13 so I have to put 877 in param 550.

How can I solve this error Feedback1Type - Invalid attribute value. Motion show module conn fault / feedback 1 type : object can’t perform services in current mode / state I try change new cable current no fault anymore and fault go to next driver why this can happened ? I don’t see software mis configured

Hello sir, i want install inverter powerflex 755 for lifting elevator, How to configure Digital output for brake system of the AC motor? Thank you

Great work dude!!! How can I get in touch with you man? Want to know if you are offering any one-to-one tutorial

Hi. Can you make a backup with the HIM with the VSD working?

nF 01 fault

hello sir, i want to ask, is it possible to move the panelview 550 mer file to panelview plus 600? please reply, thank you very much.

ahhh danke mein freund

Great vedio. I had a issue that motor runs reversely after MSO(servo on) enabled in a very low speed. Anybody had this issue?

Need more vedios form you....

Amigo qual o significado do alarme " INTERDECLARADA " ?

Hey John! Your video is amazing

Appreciate your efforts..

Recently had this issue at our plant... would've been nice to know all this info at the time, very informative thank you

thanks it did the job SUBBED

Bacana. Bem Apresentado.

Hi, where is the option "Download all ports" and for do it, do I need to do anything else or just put my HIM on the new driver and look for that option? I would appreciate your answer and this was a really helpfull video. Thank you.

Thanks

how to parameter upload download allen bradly 753 old vfd to new vfd

Usefull video

We keep getting shunt thermal overload faults and bus overvoltage faults. What's a good solution to these problems? We do have filters on the supply voltage lines fed with shielded cable.

How to solve precharge DC bus 324 Vdc alarm I use kinetix 5500 input 3 phase but modify to 1 phase

What happens if you don't even get the option to upload all ports? Just go with Copycat from device to him, I'm assuming?

Gran video!!!

Great video bud, any recommendations for excessive velocity error.??. replaced the motor and encoder and still see the same error..also tried another control module but the fault keeps coming back as soon as we try to level with other axis or perform MAM movement

Very useful info... Thanks

Hello sir, would you tell me an example to make positioning 2 motors with using the power flex 525? Thanks

Hi, whats is the restore password

What is port 0

Thank you sir