Відео

Can this driver be used to drive a transformer winding to create an inverter?

Thank you, this help me a lot,

Hello. What will happen when you apply a PWM signal to RWPM and LPWM at the same time? Will it stop or will there be a short circuit and damage? Witaj. Co się stanie gdy podasz sygnał PWM do RWPM i LPWM jednocześnie ? Zatrzyma się czy będzie zwarcie i się uszkodzi ?

Is this suitable for stepper motor?

ขอบคุณมากครับ

how do you add a josystick to control direction and speed?

haiya chawnima

Hello, how do i use the low-side MOSFET inside the BTN8982 when the load (Motor) is connected to the Vs + supply (+24 Volts) and O/P terminal (tab and pin 4)? I'm using a PWM drive signal at the input of IN while INH is held high (logic +5volts)? The datasheet shows that to select either the high-side or low side MOSFET transistors inside the BTN8982 will mean that when the PWM signal is high (+5 volt level) then the high-side MOSFET will be on therefore shunting the motor which will act a brake, which is not efficient? Any ideas?

Off topic... but how much rpm is that motor?

How to Read and Write in EEPROM this program

Hello bro can i use L298N

what is we use dual motor driver could please explain what changes should we make and we'll use 4 motor

Great one! Simple one for beginners. You haven't given the unnecessary things which will help someone to start their journey....

your diagram is something, and your actual connection is something else? where is the motor ground connection to arduino in your diagram? where is your power connection to arduino?

Hi! I'm confuse why do you set L_IS and R_IS as OUTPUTs, they should be set as INPUTs. Pin IS of the BTS7920 is an OUTPUT Pin !?! Also, I have made a schematic and L_IS and R_IS are directly connected to the respective pin 5 of the BTS7960 while all OUTPUTS to the BTS7960 such L_PWM, R_PWM L_EN and R_EN goes through the buffer 244 before interfacing to BTS7960 motor driver.

can you give the code link in ardublockly online

can you make a vedio of learning c programing and zava programing plz

Can it control 220V 1.5-2Hp gear motors?

Can I use BTS7960 to drive hub motor?

Can I use this with four motors? If yes how should the connections be?

Nice video.

too bad

Hi, I try this with two motors and they work very well but when I tri it with another servo conected to Arduino Uno, one of the motors doen't work, that it is, only one motor and the servo work well. Would yo know why?

Mashallah, khub shundor kore Bujhan. Apnar bujhanor khomota khub shundor. Apni ai tutorial ta continue korle khub valo hobe.

useless video. even the code has a bug

You're connecting 6 data pins, and you're only using 4 of them. Why?

In the sketch pins are wrong defined. The correct pin definitions are: R_IS = 1; R_EN = 2; R_PWM = 3; L_IS = 4; L_EN = 5; L_PWM = 6;

Thank you very much for this great tutorial!

this is a terrible video...

Hello. Is it possible to use plc s7-1200 which supplies PWM Pulse like Arduino to control DC Motor 24V 2A? Thank you so much.

The Arduino numbers on your diagram don't seem to match those in the code. The pins used in the code start from 2 but on the diagram they start from 1. As has already been said R_IS and L_IS should be set as INPUT and not OUTPUT

Thanks

Thanks for the tutorial

can u use 2 of this driver using 1 microcontroler to control 2 motor ? and should i connect the vcc and ground pin to the arduino ? will it burn the arduino ?

is this driver works with Wiper Motor ?

olá, pode ajudar, estou a fazer uma bike eletrica usando o arduino e a placa bts, mas tem que ter um potenciometro para controle da velocidade, como se faz pra acrescentar esse potenciometro e atualizar o programa? obrigado

Sean Lyon 4小时前 Great video! I am making a ball launching machine using a 12V 30W motor and a 16.8 Ah Lithium battery. I need the motor to spin one second and wait for 5 seconds and repeat this cycle. Would this motor controller work with this setup? Thanks

R_IS and L_IS should be set as INPUT! Not OUTPUT! They tell your Arduino board about how much current your motor is drawing!

I thought it was a double H driver.

Could you explain why you need to put both motor and battery ground together ?

Can i use MY1016Z2 Motor (250 watt with 24V )with this driver ?

the pins are wrong defined in the example sketch...

I tried a few BTS but easly burn. No protection . I do not recoment BTS7960 module.

Both RPWM and LPWM pins of my bts7960 are short. Does that mean I've burnt mt bts7960.?

could I control two parallel motors (3A max each) with that driver?

Nice one friend! I use the IBT-2 and arduino on my DIY motion simulator (full frame platform) which interfaces with Racing simulator software games! You did a good job on this post! DMAX motion simulator ch

tanks

Which hex coupler did you use for connecting the wheel with the motor ?

can we run 5 motoros by one arduino ?> with 5 IBT_2 ?

nice work