109
50 484

5:57

Fender Tone Master Pro Sound test after fix

7:57

Roland SPD SX Pro test after fix

2:01

Vox AC15HW to JMI '64 specs conversion Sound test

6:36

Laney RB4 bass amp Sound test after fix

3:35

Peavey MaxBass 110 ddt Sound test after fix

3:42

Allen&Heath Xone 92 Sound test after fix

This console came in with the initial symptoms of a faulty power supply.
After a deep check we found out that the power supply itself was faulty, but it extended the issue also to all channels independent power rails.
Once we fixed the power supply and the shorted power rails on each of the 6 chs, master and the 2 filters, we found the surprise of a static noise on the master channel and cherry on the cake, the XY fader wasnt working at all.
Luckly we manage to bring it back to life, but it has been a deep fix.
🔻
"Sybranax -
Rogue" è sotto licenza Creative Commons (CC BY-ND 3.0)
Musica promossa da BreakingCopyright: bit.ly/b-rogue
🔺

Відео

5:57

Line 6 Helix Sound Test after fix

Переглядів 291Місяць тому

This multieffects pedalboard came in with the master volume pot hidden! As usual we opened the unit and fixed the issue. Luckly for the owner the pot just came unscrewed and was no need to replace it. Ready to rock and roll

Fender Tone Master Pro Sound test after fix

7:57

Fender Tone Master Pro Sound test after fix

Переглядів 498Місяць тому

This multifx pedalboard came in dead. Probably due to using it in extreme weather conditions the powersupply board decided to give up and several components on it went to the other world. After a deep inspection we manage to identify the issues and fix it. Another gear saved from the landfill!

2:01

Roland SPD SX Pro test after fix

Переглядів 1452 місяці тому

This Roland pad came in with external triggers in ports not working. We opened the unit, cleaned the 4 flat cables, get rid of the unleaded solder on triggers in, expression pedals in and footswitches in. As shown in the video(sorry for the autofocusing going crazy) triggers works as it should!

Vox AC15HW to JMI '64 specs conversion Sound test

6:36

Vox AC15HW to JMI '64 specs conversion Sound test

Переглядів 1683 місяці тому

Amp came in with an issue in the preamp section but the owner asked us to make it to 1964 JMI specs. The normal channel gets its volume boost and the top boost its so screaming hot! Unfortunately the audio doesnt give it justice! Room is so full of sound!

3:35

Laney RB4 bass amp Sound test after fix

Переглядів 2023 місяці тому

Amp came in with the sound cutting out randomly, a couple of internal connectors burnt by previous fix attempt, several board traces on the power amp board were damaged and thick layer of solder flux that was corroding allmost all power transistors pads. Honestly this amp was on the boarder line to the landfill... but we saved it!

Peavey MaxBass 110 ddt Sound test after fix

3:42

Peavey MaxBass 110 ddt Sound test after fix

Переглядів 313 місяці тому

This little bass combo amp came in dead. We found issue in the power supply section, issues into the preamp section and cherry on the cake the class d chip malfunctioning. Amp is ready to rock again!

Fender Champion 100 Sound test after maintenance

5:57

Fender Champion 100 Sound test after maintenance

Переглядів 4064 місяці тому

This Fender amp came in for an overall inspection an maintenance. Amp wasnt too dusty inside, and it seems to be relatevelly new and in very good conditions. We gave the amp our full and deep cleaning and maintenance procedure. Amp is working just as it should!

4:19

Roland JC120 Sound test after fix

Переглядів 1164 місяці тому

This JC120 came in after a couple of days it was handled to its owner after an overall maintenance and the external speakers out mod. For unknown reason one of the 4 internal fuse on the power amp rails failed, so we proceed to check if there was any power transistor fail or not. Luckly, and after testing it deeply, it was just a stressed fuse that decided to pass to a better life. Amp is healt...

4:42

Ampeg SVT 450 sound test after fix

Переглядів 2164 місяці тому

This Ampeg bass amplifier came in with cutting off sound randomly. After a deep inspection we found a previous fix attempt on the gain pot with its connections without any insulations, cold solder joints on allmost all pots and in/out jacks and a ton of dust. We gave the amp a deep clean, replace the gain pot with insulated wires, replace all suspicious cold solder joint with a fresh leaded one...

6:32

Line6 Helix Sound test after fix

Переглядів 1264 місяці тому

This Helix came in with several issues: faulty footswitches, randomly the system will freeze itself and a bent encoder. Lets begin with the easy part, the bent encoder caused by a bump or a kick. Footswitches were working really bad thanks to a faulty controller and cherry on the cake the unit wasfreezing itself due to a power rail components fail(be sure where your gear is plugged in). The ped...

Presonus Central Station sound test after maintenance

5:52

Presonus Central Station sound test after maintenance

Переглядів 934 місяці тому

This rackmount control station came in with no sound coming out the three left speakers out. After a quick check to be sure the issue wasnt coming from some components failure, we proceed to disassamble the entire unit and give it a deep clean and maintenance. As the video shows, all speakers outs works as it should!

3:04

Blackstar U250ACT sound test after fix

Переглядів 374 місяці тому

This Bassguitar frfr came in dead. After inspections we found issues in the smps section and in the poweramp section. Both on the same board. After severals mails with blackstars and korg both of them pointing each others for assistance, we decided to waste no more time with the maker and the distributor (childish game) and replace the entire board with a wellknown and relieble brand. The cab w...

Ehx Bass MicroSynth sound test after fix

6:03

Ehx Bass MicroSynth sound test after fix

Переглядів 594 місяці тому

This pedal came in after the owner gave it a 18v shot. After inspection some components in the power supply section failed due to overvoltage and all signal related integrated circuits passed to abetter life. Note to everyone, this pedal acept only 9v, unless you are tired of it and want to buy a new microsynth. Only in this last case you can apply 18... 27 or more volts and watch it die in a f...