- 36
- 47 301
Your•Car•Mate
United Kingdom
Приєднався 7 бер 2023
🚘🔧 "Grease monkey at heart, fixing cars is my art.
Sharing my passion for all things mechanical.
#MechanicLife #AutoRepair #CarEnthusiast"
Sharing my passion for all things mechanical.
#MechanicLife #AutoRepair #CarEnthusiast"
Audi A4 Car Service Guide: Oil, Air, Cabin, and Fuel Filter Change
Here's a short step-by-step guide on how to perform a full service on an Audi A4 car:
Changing the Oil:
1. Lift the car using a jack and secure it with jack stands.
2. Locate the oil drain plug under the engine.
3. Place a drain pan beneath the plug and remove the plug to drain the old oil.
4. Replace the drain plug and tighten it.
5. Remove the old oil filter using an oil filter wrench.
6. Apply a thin layer of oil to the rubber gasket of the new oil filter.
7. Install the new oil filter and tighten it by hand.
8. Add the recommended amount of new oil through the oil filler cap.
9. Start the engine, let it run for a few minutes, and check for leaks.
10. Turn off the engine and check the oil level using the dipstick. Add more oil if needed.
Changing the Air Filter:
1. Open the hood and locate the air filter housing.
2. Unclip or unscrew the housing to access the old air filter.
3. Remove the old air filter and clean out any debris from the housing.
4. Insert the new air filter in the same orientation as the old one.
5. Reattach the housing, making sure it's securely fastened.
Changing the Cabin Filter:
1. Open the front passenger door.
2. Locate the cabin air filter housing under the dashboard on the passenger side.
3. Open the housing and remove the old cabin filter.
4. Clean out any leaves or debris from the housing.
5. Insert the new cabin filter with the arrow pointing in the direction of airflow.
6. Close the housing securely.
Changing the Fuel Filter:
1. Locate the fuel filter, usually near the fuel tank or under the car.
2. Relieve fuel system pressure by removing the fuel pump fuse and starting the engine until it stalls.
3. Use a line wrench to disconnect the fuel lines from the filter.
4. Remove the old fuel filter and install the new one, aligning the flow direction arrow.
5. Reconnect the fuel lines, ensuring they're properly tightened.
6. Put back the fuel pump fuse.
7. Start the engine and check for any fuel leaks.
Remember to consult your car's manual and follow safety precautions while performing these tasks. If you're not comfortable or experienced with car maintenance, it's recommended to seek professional assistance.
Changing the Oil:
1. Lift the car using a jack and secure it with jack stands.
2. Locate the oil drain plug under the engine.
3. Place a drain pan beneath the plug and remove the plug to drain the old oil.
4. Replace the drain plug and tighten it.
5. Remove the old oil filter using an oil filter wrench.
6. Apply a thin layer of oil to the rubber gasket of the new oil filter.
7. Install the new oil filter and tighten it by hand.
8. Add the recommended amount of new oil through the oil filler cap.
9. Start the engine, let it run for a few minutes, and check for leaks.
10. Turn off the engine and check the oil level using the dipstick. Add more oil if needed.
Changing the Air Filter:
1. Open the hood and locate the air filter housing.
2. Unclip or unscrew the housing to access the old air filter.
3. Remove the old air filter and clean out any debris from the housing.
4. Insert the new air filter in the same orientation as the old one.
5. Reattach the housing, making sure it's securely fastened.
Changing the Cabin Filter:
1. Open the front passenger door.
2. Locate the cabin air filter housing under the dashboard on the passenger side.
3. Open the housing and remove the old cabin filter.
4. Clean out any leaves or debris from the housing.
5. Insert the new cabin filter with the arrow pointing in the direction of airflow.
6. Close the housing securely.
Changing the Fuel Filter:
1. Locate the fuel filter, usually near the fuel tank or under the car.
2. Relieve fuel system pressure by removing the fuel pump fuse and starting the engine until it stalls.
3. Use a line wrench to disconnect the fuel lines from the filter.
4. Remove the old fuel filter and install the new one, aligning the flow direction arrow.
5. Reconnect the fuel lines, ensuring they're properly tightened.
6. Put back the fuel pump fuse.
7. Start the engine and check for any fuel leaks.
Remember to consult your car's manual and follow safety precautions while performing these tasks. If you're not comfortable or experienced with car maintenance, it's recommended to seek professional assistance.
Переглядів: 164
Відео
Took 6 Hours To Do This Job Instead of 1 🤣
Переглядів 11Рік тому
Took 6 Hours To Do This Job Instead of 1 🤣
Watch me Replace a Water Pump on BMW 1 Series: Step-by-Step Guide
Переглядів 4 тис.Рік тому
Watch me Replace a Water Pump on BMW 1 Series: Step-by-Step Guide
Clutch Replacement Ford #autorepair #carmechanic #carrepair
Переглядів 62Рік тому
Clutch Replacement Ford #autorepair #carmechanic #carrepair
🙂 Promo SM
Fk me you had the money worth out of them
Lol😮😮😮
???
Had a customer walk into our shop claiming that we ripped her of on the hours worked on her timing belt replacement. Because "the tik tok guy just needed 1 minute" while it took my coworker a few hours. But anyway amazing job looks clean keep it up my guy.
YeA🎉🎉🎉🎉
By the off
They all think like that 🤦🏻♂️ Looking on UA-cam - "I can do this myself"; Go and do it then, don't waste my time 😁 Thanks 🤝
when it wont come off use HEAT!
Easy to say...harder to do when on a budget
invest in a good torch, heat will be your friend
It doesn't even have to be a good torch, a little $20 plumbers torch and tank combo does just fine. Add a couple rummage sale candles, and a little watering can and you can save yourself so much trouble.
I have that already, but customer wanted to 'save' the bearings. Lack of funds...
He will come back for bearing noise soon, means extra money for you! Since he wanted to save money not replacing the bearing when already removed.
@@SmokieMcgee The bearings were already a bit noisy(probably the original ones) but the customer said he doesn't mind.
Why would engineers put the hub outside of the rotor??????
Honda did that with the 95 Accord. 4 bolts holding on to dear life. If you strip one bolt, it really sucks from experience. Toyota did that with their pickup trucks. Take the wheel hub off and remove 6 big bolts at the back side of the hub. Hammer it out.
Have no idea. A lot of things on cars are designed in the worst possible way. Like they don't need servicing
2 words, 1 tool: Hub puller
Tried that. It did not work. Just didn't have time to film it
Very good job, and professional.
Thank you 🙏