- 42
- 24 456
Ski3D
United States
Приєднався 7 лис 2023
Відео
Creeping the speeds up Troodon 300+ mm/s
Переглядів 309 місяців тому
Creeping the speeds up Troodon 300 mm/s
k1 Baby EasterDragon PLA 6h59m Timelapse
Переглядів 4410 місяців тому
k1 Baby EasterDragon PLA 6h59m Timelapse
k1 Lid Extension PETG 4h17m Timelapse
Переглядів 6710 місяців тому
k1 Lid Extension PETG 4h17m Timelapse
k1 Modular Spool Holder Base4h12m Timelapse
Переглядів 3010 місяців тому
k1 Modular Spool Holder Base4h12m Timelapse
Это я на работе изображаю кипучию деятельность
What gantry and rail kit did you use for the upgrades?
github.com/tlace17/K1-Linear-Rail-Gantry
I think you can buy a kit with motors and gantry now
@@Ski3Di think this link is not working
bro I don't even know what to say to that, that's crazy
❤
Now to actually print something😂😂😂
@peelthestickers it doesn't need to print. it just needs to go fast. 🤣
GOD DAMN
48 power supply and tmc5160t pro comes in this week, so it should be a little faster 😁 will post an short when finished.
Got the 48v video posted!
Go with 0.03
Do you have a guide to everything you've done to the Troodon V1?
Not really, biggest upgrade is going to a voron 2.4 style gantry. But this printer does run klipper with an octopus pro, 24v and 48v power supplys and AWD.
CHANGE THAT BED
"Flips bed sheet"
Pretty easy to make upgrades?
@@jacobstuntz8617 yup, I think so
Mine has been nothing but problem after problem. What pulley housings are those ?
Fushi F623RS
github.com/tlace17/K1-Linear-Rail-Gantry
I think the results can be better with better tuning, maybe it's max possible output with those components Im getting 30k accel and 800mm/s on my Voron 2.4 350 with only two stepper motors for XY, with 4awd the results should be better
I I'm guessing you never used awd then, I'm sure you can pull them magical numbers out your ass. But it's not going to happen. People using the ldo kraken motors are getting around the same. I was easily getting 1000mm/s at 30k on a 400 with two steppers at 48v
@Ski3D ILIKE3DPRINTERS your such a troll. I bet your results would be better. 🤣
Comments like ilike3dprinters are people who bought their first voron and identity as 3d printing master now that they built a printer. I normally post stuff I'm working on, not trying to impress anyone and if you can do better I'm sure I can get a group together and Start a slow clap for them.
@@Ski3D so what's the reason to use 4awd if not to get more torque?
@@Ski3D Im just confused of your machine output
Does it print in good quality? Because that’s important
Yes, but I also don't print at them speeds, mostly travel speeds.
@ nice
Now print a benchy at that speed and see how it turns out
It's going to look good 15k accel is so low, that this printer would not achieve even 200mm/s on benchy, because there is no such space to accelerate
Your math is a little off... easily over 200.
@@Ski3D it's not bit off, it just depends from length of travel, that I didn't mentioned The calculated top speed for 2cm distance is 500mm/s, but the benchy has mainly tiny distances, so the average speed will be much much lower So for 5mm distance the top speed will be 250mm/s
Ok 👍
Must be out it filament
No, just a speedtest
Oh nice
Oh thanks!
FULL SEND!!!!😮
What are you tryna print? Cocaine?
Dang that's fast
I like your printer
❤
holy fuck
I just got a K1 Max. I cant believe how good it prints and how blazing fast. Beats the crap out of my Bambu on both
I upgraded to a K1 Max from an old Lotmaxx Shark V2... 20mm/s was too fast for the Shark, now I'm doing 320mm/s lol
Once you go fast you can't go back lol
@@Ski3D Like Ricky Bobby said, "I wanna go fast." lol
Why.... put..... gluestick.... on pei...especially textured.... It's not even remotely necessary.
@@jackshett i.....dont.....care....
Also......when using both side fans and part cooling fan when printing fast, the cooling will cause my prints to release from the pei bed. 🫡
Did you evr post about the board setup, config files, etc. Or just showing it?
did you by any chance shorten your belts or use different ones? im doing this mod now from the github but my belts are way to loose even with the tensioners all the way. i might be missing something here. :O
Yes you will have to shorten them a little bit
@@SilentRush420 Thanks for the reply!
With the tensioners all the way loose, tighten the belt at the hotend first. And cut the rest off. Keep them equal
Gotcha sound like the plan going forward
Is this worth it? Have you seen a noticable improvement in print quality?
Hands down best upgrade, night and day difference in quality and input shaper results.
Do you have before and after results?
I've literally been looking for this MOD on a K1MAX done by ANY1 for weeks! Thanks bud PS. Great song choice.
@@AnthonyPadilla-m7y github.com/tlace17/K1-Linear-Rail-Gantry
❤
Nice
😮
Nice
Nice
So cool
Do have some tipps for me because my cyclops does not work properly. I printed my body out of an sls-printer in nylon pa06. the necessary pressure of the spring or the perfect fit of the insert nut for the filament. Thanks :)
The stl was designed for fdm, I seen sls would be little loose for the bearings. A good starting point would tighten it all the way then loosen one turn. What kind of problems are you having really?
'PromoSM'
Link to design??
@@jack61670 github.com/tlace17/K1-Linear-Rail-Gantry
❤
😮
That bad boy is *quick*
Eevee!
Nice!
Thank you! Cheers!
Cool❤
That's what im talkin about