Відео

thank you for video, can i ask one question? If i want add heat to the workpiece, example use laser add heat to workpiece, how can i show the add heating in Simulation?

Very helpful video

What happens if i increase the pressure to 10000N

Hi.i try this method with another model but after i simulate the beam stays down and doesn't vibrate.what's the problem?

Thank you for sharing knowledge!!

Thanks!

what software is this? SAP2000?

Please post full video for tutorial

thank you man, you r the best ❤❤

Great tutorial! Thank you for the explanations.

Why dist / rev ratio is 300 ????

Hello Sir, Where can I find the springback angle?

THE *TIE PAIR (ASSEMBLY_Top Plate-Bottom,ASSEMBLY_Top Cohesive- Bottom) IS ALSO USED AS *CONTACT PAIR. REMOVE THIS *CONTACT PAIR. THE SAME PAIR OF SURFACES CANNOT BE SPECIFIED MORE THAN ONCE FOR *TIE AND *CONTACT PAIR. ONCE A PAIR OF SURFACES IS USED FOR *TIE, IT CANNOT BE USED AGAIN FOR *CONTACT PAIR AND VICE VERSA. Getting this error What to do?

Good Video, but when I import, Abaqus give me a messege; The part "peça" contains imprecise geometry, which is highlighted. Partitioning and quad hex meshing using the medial axis algorithm may fail on imprecise parts.

Tell me sir, is it possible to add other interactions such as for example sliding and rolling friction as well as heat flow due to viscosity. above all tell me how to apply them, can we apply them to the plate directly or we must apply them to the Eleurian body.

Didn't you mesh the wp and assign the section?

I want the plate to be rigid, what should I do????

THIS KEYWORD IS NOT AVAILABLE IN Abaqus/Explicit Analysis will be terminated Analysis Input File Processor exited with an error. i am getting this error can you please explain me sir

hello. I have inquiries that i needed a brief direct discussion . How can we get in touch asap

very helpful, please make a video on piezoelectric intelligent composite's delamination especially for multiscale simulation

Thank you for this amazing video, I fallow you . 👍

thank you Sir but can you tell how can i find a longitudinal natural frequency axial vibration please

Great simulations. Which element, and what type of Boundary conditions, did you use for the structure?

Hi sir, I need a CAE file of this simulation.

How to simulation the rocket impact and explopsion? Please help me. Thank so much

Could you please share complete video please 🥺🥺

Hi, may I know how does it works for compression loading?

I need some help regarding this type of simulation. Do you help others regarding simulation?

merhaba benim yaptıklarımda tam delme yapmıyor yardımcı olabilirmisiniz

can u post tutorial for this simulation?

i love it thx

Hello sir i followed every step and in data check i getting output not available for element type ec3d8rt

Could you please share this file?

did you use the same material for both disc and pad?

bokachoda pls try to speak clearly

re bhai cursor use korte ki hoy??

What are all the changes can I make for Rotary friction welding by referring this video?

Sir/Mam, The video was so informative. I couldn't able view the results as in the video like impactor going up and falling down at the beam. Can you please suggest the steps.

can you give me the parameter of pressure and material?

Sir have you used any subroutine codes using FORTRAN etc in this abaqus analysis for heat flow

At minute 9:01, do you mean tonne/mm3 instead of kg/mm3 ? The value of 2.7e-09 corresponds to tonne/mm3 unit.

thanks for your detailed FSW video. Why do you take 2 different film coefficient values for the bottom and all other surfaces? Please try to clarify. Thanks

sir can i ask on how to change the feed rate ?

Great work. Do you have an idea about EDEM-ANSYS Fluent coupling for friction stir welding?

Hello sir, thanks for the helpful tutorial. I have a question about BCs you assigned for the Tool, the rotation speed is 500 radians/time. It means the speed is appox 4777 rpm. Is this right?

thx

Dr i want to do simulation on Abaqus please 🙏 guide me from where to start . I have no idea about this . Waiting for your response

Hello . Thank you for your great Tutorial . i was looking for the method of extracting moment and shear diagram and it is exactly what i needed . Thank you sir

Sir how to apply tensile load on each side of the plates of the friction stir welding

Hello sir may I buy this file from you either in case or in version