- 84
- 102 165
Brandon Zgadzaj
Приєднався 1 лис 2011
Titan DLX Test
Just a test with the 360 GoPro
Testing jets or for the carb and decided to get a short pull in while I could
Testing jets or for the carb and decided to get a short pull in while I could
Переглядів: 54
Відео
Modern Warfare crossmap throwing knife
Переглядів 152 роки тому
Modern Warfare crossmap throwing knife
Call of Duty: Modern Warfare Collateral
Переглядів 163 роки тому
store.playstation.com/#!/tid=CUSA08829_00
Call of Duty: Modern Warfare Rennetti Massacre
Переглядів 93 роки тому
store.playstation.com/#!/tid=CUSA08829_00
Call of Duty Modern Warfare throwing knife kill
Переглядів 93 роки тому
store.playstation.com/#!/tid=CUSA08829_00
Modern Warfare Pistol Rampage
Переглядів 154 роки тому
Call of Duty®: Modern Warfare® store.playstation.com/#!/en-us/tid=CUSA08829_00
Hidden Bankshot
Переглядів 184 роки тому
Crazy throwing knife kill into a building Call of Duty Modern Warfare
Bankshot 180
Переглядів 104 роки тому
Call of Duty®: Modern Warfare® store.playstation.com/#!/en-us/tid=CUSA08829_00
Jami Pelligrino’s flop at trail hero 2017
Переглядів 406 років тому
Jami Pelligrino’s flop at trail hero 2017
Jami and Tony Pelligrino running the course
Переглядів 116 років тому
Jami and Tony Pelligrino running the course
Did you hone or bore the cylinders?
Just did a big bore 478
(there is a pending code for P1345, blank, diagnosed it and found that this code typically is related to excessive wear in the cam shaft, causing the timing to be incorrect, to correct this issue, he recommends replacing the cam as well as the timing chain components ) what’s the possibility about this being true?
You should just be replacing the distributor or the cam gear The Cam is a harder metal so no need to worry about replacing the cam or chain
Still play cod huh dude!!! It’s been Awhile
Yes I do you need to play with me
84hp lol show the dyno
You made 50% more horsepower over stock with an extra 82cc's? BS...you can tell by how it's revving it's nothing exotic.
I'm pretty sure it has more done to it
The hell you need all that power for? It will dig you a grave before you plant all that power to the ground on a mx track. Unless it's for street racing.
What the you racing ? Street bikes 🤣💪 my 450 with 54hp is way more then enough for me you got some balls of steel racing that machine 👍😎
😅😂😭💀🤦🏾♂️ Ong
That boi might be drag racing
How much power...
84hp
@@lambbolt thats shit
@@samojanovicek5931 are you ok?
That’s right🙌🏼
The timing on 97 and up models is not mechanically adjustable, its all computer controlled. Rotating the distrubutor does nothing.
That's a lie
Correct, you have to have a scan tool to set the timing. It's set on 0 + or - 2 degrees Little bit of leeway but runs best on 0 degrees. Part # Accel 59132. Summit racing plug and play distributor billet aluminum. $188.00.
U mean 350?
yes
there is a 250 banshee
Are you sure you turn the distributor counter clockwise to advance spark??? i thought it was clockwise to advance ...thanks
@moto madness
Not all for vortec's.
im 12 and have a 25o 2 stroke
i have same engine. What's cylinder pressure before and after rebuild? thanks
trisuny before it was 110 top 30 bottom After 180 177
ive got a 96 5.7 vortec and my computer shows normally 22-23 for cam correlation and as such I have the code for it. Truck runs decent when cold but once it warms up it spits and sputters. Just bought it so im not sure if someones replace the distributor in the past or not. Cap looks newer.
TheFrontYardMechanic yeah I would try and just adjust it for now
Ive been reading up on it and was wondering about the worn gear myself. cam correlation seems to bounce around a bit so I believe the gear is a bit worn but I think most of it is that you may be right and its off by a tooth. Been fixing other things on it (bad o2 sensors, went ahead and replaced both pre-cat sensors with new ACDelco ones) Ive also read that going by timing marks on the balancer is the best way regardless of what sensor claims. If I get a chance tomorrow ill try to check the play in the gear and time it. I imagine if theres play I should be able to slightly rotate the rotor a little back and forth. Overall it has tons of low end power for having 257k on it lol. Mid-top end has a little to be desired but hopefully this may take care of that. At some point if I can find a marine intake I want to slap that on there and get rid of that plastic intake and spider injection junk. Runs better now warm after changing those o2 sensors.
Also sometimes the harmonic balancers will vibrate and timing marks will change
i have gone through so many videos just to get this simple piece of information! God bless you. Thank you for posting this.
KillTheFear if you have any more questions just ask I'll help
lol same here thanks I'm actually at +15 to +30 how would I got "back a tooth" I tried this method but it seems to not get me under +15
Let's see some surf vids and turn your stupid camera sideways. Nice boat by the way. Last of the x1's. I hope to find one for sale in the next year.
What year is your Dakota and what year was the ram
1999 Dakota 383 hemi 2000 ram 3500
Badass. Hey how do you get your mirrors from a Dodge Ram. I hate my little Dakota mirrors.
They bolt right up to the holes on the door
Nicee! Are you wired to .5 or 1 ohm? Also what alrernator you got?? Your system is bumpin hard man
I've got a mechman 370 And 1ohm
It hits a lot harder now I did a new deck that lets me adjust the eq and a new amp loving the system
RICER ALERT 14:50
It's also hooked up to a water line to cool it
It was built as a competition ski so you can go shove it
XD
I know right fricken cod man bad cod bad bad bad
WTF
yes I would
Lol you would wait there
Whaaaaaat how's that possible
strong arm
Dam your so good
Did you just orgasm?
You were not in this game
Lol wasn't trying
We were playing gun game and he could not get me
Try hard lol
Swag
Bring it noob
Ok
Oooo killem ktm you gotta make a 1v1 knife me you