Відео

Good stuff. Mine didn't have connection issues, but the screws had loosened up. I wasn't aware of the third screw under the insulator.

In order for ATO to look nice, you need to apply 1 heavy coat by wiping it on in one direction only. The back and forth strokes you did will make it look splotchy and uneven.

If these radios work then they paid for a lifetime subscription the reason I know I have a pioneer inno radio that I don’t pay for

Does anyone know what could be causing my Dolby surround to not work anymore? The switch on the headset and the button on the mixamp does nothing. I can open it up again, but I don't know which side is the culprit or what to even test for.

Never EVER use a jack alone to support the weight of a vehicle. The seal on a hydraulic jack piston can blow out at any time. Jacks are for lifting and lowering vehicles not for supporting weight. That's what jack stands are for. Don't find out the hard way by dropping your vehicle on its rotors or even worse dropping the vehicle on yourself. It's a very important thing to teach your kids as well.

Can you use the polish without the auto scrubber.Is there another method? Great job btw

GREAT VIDEO THANKS MUCH!

I have a Onkyo TX NR7100 and unable to access the 2.network or 3.Bluetooth menus under Hardware setup nor am I able to access the 3.firmware update or 4.initial menus under Miscellaneous setup. Any ideas how to correct this problem.

2024 and this video is still relevant. Only took me 3min start to finish. Thx for the tip.

Thanks

"Solubolize"??? That's a new one for this 67yr old fart!

Algorithm post

How does it work on auto headlights?

Removing the wireless lan got me

Try some PB Blaster spray. Mine came off after sitting for a few minutes with the spray.

Same problem! If I move my boom, it disconnects. I just got it. Should I send back?

Thanks so much! Could definitely do it myself if I wasn’t 8 months pregnant 😏

Do you leave the light on all the time ?

Does it work on the A20?

Good video

Well done

Good job

I thought a blizzard was a lot worse than that

Cool bro!

but how do you open the gen 1 oontz angle?

Ya got to go all the way to the 8000 grit and a buffing pad suede pad. You must be or have a strong Virgo influence, "Craftsmanship"! I share the trait, pristine perfection feels great! Love it! You go!!!

Watch your words! Oxides are inevitable. We cannot live without God given oxygen.

I use this product and it’s just “so so” but will continue to do it because none of them are that great but thank you so much for your video. It made me laugh. I really enjoyed it.

I have a pair of VR975s and they keep blowing the fuses. Any idea as to what be causing that?

Dows it make the floor slippery though?

Many many thanks! After a year finally u fixed my problem!!!!!

what the hell, I just opened up TX sr607 and found a hdmi port on the controller board but no hdmi cable attached to it.. I got it used from someone and the guy wasn't even using hdmi ports. all my INs and OUT is not working for HDMI currently,,

My man would never mop a floor 😢

Get rid of the gate valves, they are a terrible design and prone to failure due to corrosion and mineral deposits. The stem in the valve rots and will snap one day when you try to shut it off. Or, you might be able to shut it off, then it snaps when you turn it back on. I know this from personal experience. Replace them with 1/4 turn ball valves.

Jeez dude just get to the point

❤

Wrap a badly corroded terminal in alluminium foil to get better contact.

Can you put seafoam in the piston/spark/plug hole with new oil and gas?

Does this need any type of glue to put the screen back on? Didn’t see anywhere you mentioned that. 🤷🏾‍♂️

how does the screen go back on and stay on?

What is the piece called?

I just wired up a new button to the board and drilled a hole in the body to create a physical Overdrive button works great

2017

How do you know when it needs a change or justment? I have a guitar with the same problem and although I already ordered the parts I don't know if I can do anything to repair it before soldering

6:40 Best feeling in the world

I just want to say thank you it helped me

Great video where did you get the HF-11 filter I cannot find that vacuum or filter on Eureka website I have the same vacuum. I have tried Amazon and cannot find the filter. Thanks

Great video; was quite precise, & enabled me to get my job done! Thanks much!

Be serious. No way the average Joe can do that. Totally frustrating

this made my usb port explode out