Nice stove! Love these little powerhouses. Lots of power and great simmer control in all weather. A classic. While these are a bit more cold blooded than their single control brothers, they don't need preheat if you follow the instructions. Lots of pressure, flame adjust to high, lit match to burner, valve to light. As soon as it lights, add pressure. Anything else prolongs the process by not allowing enough air into the fuel air mixture at startup. Yes with the two control models, you'll probably see a couple of flares, but make sure the lighter/match is lit and ready BEFORE opening the valve. That said, a proper preheat will have you ready to cook as soon as it's lit. This was not that. Nor do I believe it was intended to be. More of a warmup to help it along. But it clearly lacked pressure. If the instructions don't work, there is something wrong with the stove. The more pressure you have, the less fuel, and more air, that gets delivered to the generator and the better atomized that fuel is to reduce flooding. Think of the instant lighting system like a can of spray paint. Which will give you the smallest droplet size, a can with 5psi in it or a can with 100psi in it? Obviously, Coleman knew this model was prone to flooding, though. They included the wick material in the mixing chamber for a reason. Like pulling off a band-aid or yanking a tooth, go full blast and get it over with as quickly and painlessly as possible. I have nothing against preheating. However, most folks do so unnecessarily and don't follow the lighting instructions as written. Failure to follow the lighting instructions has scared off more potentially happy white gas users to propane than anything else in stove history. Not following the instructions is why Coleman only makes a couple of liquid fueled stoves today where they used to have dozens of models to choose from. RTFM
Sorry, didn’t understand the detail. The test was successful, did the copper wire replacement shrink? Did it catch any residue? Was the fuel usage normal.
Not wise to get in the habit of using the cleaning needle as a shutoff. It's a good way to flood the vaporizer and possibly, though not likely, burst it if you close both the main valve and shut off with the needle. No where for the expanding fuel to go. Nice stoves that will last many lifetimes.
ANOTHER FIFTEEN MINUTE VIDEO THAT SHOULD HAVE BEEN 6 MINUTES LONG AT BEST. Good content and process but way too long. I advanced through it and got the concept. Watching a process TEN times is totally unnecessary repetition. Especially "miking" each finished piece. Were not building a CLOCK here. And, Thank-you, no. I have never posted a YT video. So, I don't know to post. But, I think l know when a video is too long. This comment was not ment to be confrontational and I hope you did not take that way. And, a lot of the video close ups were out of frame. Again, constructive criticism.
Thank you for your suggestions. This is just a sharing channel and not a professional YT channel. I think some people may still need it, but I will still listen to your suggestions...Thank you
With mine Attach soaked in meths preheat, make sure pump is loose ( no pressure in tank), light, just as preheating unit starts to run out, crack valve, screw up pump, about 10 pumps it will start to light, once it has done a couple of splutters, pump till pressure indicator rises, adjust control as required for light output. Total lighting time, about 3 to 5 mins depending on ambient temp Yours needs new pump washers
Might be a subjective question but what's a fair price for this exact lantern? A lady locally is selling one but she wants $200 for it! Just seems kinda high right?
@@gavinchang55 Well, now she would take around $60 for it. Would that be a fair price for it? There's a couple blemishes but besides that it looks new.
@@jamie-r2034 I didn't see the lantern, but I think it should be worth buying for $60 , or you can go to eBay to refer to the price before deciding whether to buy this lantern
@@gavinchang55 Thank you. I got the blue/black big hat sears one and thought it would be cool to have the Avocado colored one too. I know the frosted glass is pricey as well. I'm new into this so just asking anyone who is in to these as well.
@@gavinchang55 Follow up: The lady messaged me after not being able to sell it. I got this exact lantern & another Coleman 220F with parts safe that had tools, mantles & new generator. I paid $80 for both! The Sears has a few blemishes but besides that is perfect. It's by far my favorite lantern I own now.
I have same problem removing old packing from inside nut but don't understand what you said. How did you remove packing from but and not damage but threads?
I gave up at 2:12 since much as I like in-focus sunflower tiles I learned nothing from the blurry failed close-ups. I can't believe that at no time over the last 2 years you've considered making an in-focus version.
Those shades look like globes from Coleman lanterns??? What models??? Wish I could get my 132A running. It has a split tube just blow the valve assembly. The split in the tube is about an inch long. W Rusty Lane K9POW in eastern Tennessee
Just came across your nice vidéo. Nice music too 👍. Have two Coleman, one Petromax and lately purchased one of those marvel of a lantern. Still waiting for it to arrive. I use them all in my RV for lighting and heating as well.... With a BIIIG fire extinguisher nearby of course.😁
請問在 03:33您要放石墨環進去前 那個寬一點的銅環 是 哪一邊挨著石墨環? 是平的 還是 有錐度的 感謝您
@@wuwuab 我的是兩邊都是平的，有錐度應該也沒差，能逼緊就好
@@gavinchang55 非常感謝回復 我是 502..
@@wuwuab 有印象在蝦皮問過我，哈哈
Awesome I got the same for 9 bucks. I'm gonna use gasoline in it not white gas. Come fight me!
Where can I I buy this?
ebay
That is a very beautiful lantern, thank you for sharing.
How not to light a lantern
I use Bronze wool for my packing
great hissing
Lindo !
Just decided to rebuild mine, been sitting since the 80's
How do you turn it off?
Close the lid , extinguished due to lack of oxygen
Where can one acquire those molds at?
I have put the file location in the description, you can use 3D printing to make it yourself
Mine won't pump up. What might be the problem?
It may be dry or rusty and stuck.
Great tutorial and lovely lamp thanks for sharing.
That stove looks suspiciously similar to a Swedish stove
抱歉不小心把留言刪了，已入手感謝😂
Is it possible to launch this lamp with only matches? What fuel is best to use?
It may be possible to light it with a match, but I haven't tried it. It seems to be more difficult. Use white gas or Coleman fuel .
@@gavinchang55 I live in Russia, my friensd and we do not have any Coleman products. Can I use kerosene for lamps or pure gasoline?
@@ДмитрийВдовенко-я4о Kerosene is not suitable, but gasoline is ok
@@gavinchang55 Thank you very much! I bought this lamp yesterday, there are very few of them in Russia. I'll try to light it, good luck)
@@gavinchang55 My friend, allow me one more question :) what is the volume of the tank and what is the fuel consumption per hour at maximum?
I just bought the same lantern. It hasn’t been used in 80 years the original family told me.
U.S issued those m1950 stove burners during the korea war
Nice stove! Love these little powerhouses. Lots of power and great simmer control in all weather. A classic. While these are a bit more cold blooded than their single control brothers, they don't need preheat if you follow the instructions. Lots of pressure, flame adjust to high, lit match to burner, valve to light. As soon as it lights, add pressure. Anything else prolongs the process by not allowing enough air into the fuel air mixture at startup. Yes with the two control models, you'll probably see a couple of flares, but make sure the lighter/match is lit and ready BEFORE opening the valve. That said, a proper preheat will have you ready to cook as soon as it's lit. This was not that. Nor do I believe it was intended to be. More of a warmup to help it along. But it clearly lacked pressure. If the instructions don't work, there is something wrong with the stove. The more pressure you have, the less fuel, and more air, that gets delivered to the generator and the better atomized that fuel is to reduce flooding. Think of the instant lighting system like a can of spray paint. Which will give you the smallest droplet size, a can with 5psi in it or a can with 100psi in it? Obviously, Coleman knew this model was prone to flooding, though. They included the wick material in the mixing chamber for a reason. Like pulling off a band-aid or yanking a tooth, go full blast and get it over with as quickly and painlessly as possible. I have nothing against preheating. However, most folks do so unnecessarily and don't follow the lighting instructions as written. Failure to follow the lighting instructions has scared off more potentially happy white gas users to propane than anything else in stove history. Not following the instructions is why Coleman only makes a couple of liquid fueled stoves today where they used to have dozens of models to choose from. RTFM
Sorry, didn’t understand the detail. The test was successful, did the copper wire replacement shrink? Did it catch any residue? Was the fuel usage normal.
Hi please refer to another video linked below ua-cam.com/video/PK-DxuzwIWY/v-deo.htmlsi=J2v6jasnjJc4D13a
谢谢张先生，我打算周末用我的皮带做实验，买了一个Coleman的皮碗做标准，这玩意看起来毛毛的能密封么，还是需要打磨了加油靠油密封
你好，皮碗完成後使用前要先泡個機油或針車油，皮碗吃飽油後就有密封效果了
Great video and beautiful made pump cup leathers 👍 Do you also oil the leather sheet or finished pump cups to keep them soft and smooth?
I soak the leather sheet in oil for a while before use.
Not wise to get in the habit of using the cleaning needle as a shutoff. It's a good way to flood the vaporizer and possibly, though not likely, burst it if you close both the main valve and shut off with the needle. No where for the expanding fuel to go. Nice stoves that will last many lifetimes.
真他妈漂亮
Great to see this beautiful lantern. Thanks for sharing.
امتلك واحد مثله 500A واعتمد عليه كثير في رحلاتي
ANOTHER FIFTEEN MINUTE VIDEO THAT SHOULD HAVE BEEN 6 MINUTES LONG AT BEST. Good content and process but way too long. I advanced through it and got the concept. Watching a process TEN times is totally unnecessary repetition. Especially "miking" each finished piece. Were not building a CLOCK here. And, Thank-you, no. I have never posted a YT video. So, I don't know to post. But, I think l know when a video is too long. This comment was not ment to be confrontational and I hope you did not take that way. And, a lot of the video close ups were out of frame. Again, constructive criticism.
Thank you for your suggestions. This is just a sharing channel and not a professional YT channel. I think some people may still need it, but I will still listen to your suggestions...Thank you
Very nice, thanks for sharing.
加油
With mine Attach soaked in meths preheat, make sure pump is loose ( no pressure in tank), light, just as preheating unit starts to run out, crack valve, screw up pump, about 10 pumps it will start to light, once it has done a couple of splutters, pump till pressure indicator rises, adjust control as required for light output. Total lighting time, about 3 to 5 mins depending on ambient temp Yours needs new pump washers
can use kerosene
Would you make some to sell an where do you fined your leather thank you so mutch for a great. Vidio
Thank you for your suggestion, you should be able to buy it in leather diy stores
Might be a subjective question but what's a fair price for this exact lantern? A lady locally is selling one but she wants $200 for it! Just seems kinda high right?
Yes, it's quite a subjective question. SEARS lantern is indeed becoming more and more rare, especially the beautiful ones .
@@gavinchang55 Well, now she would take around $60 for it. Would that be a fair price for it? There's a couple blemishes but besides that it looks new.
@@jamie-r2034 I didn't see the lantern, but I think it should be worth buying for $60 , or you can go to eBay to refer to the price before deciding whether to buy this lantern
@@gavinchang55 Thank you. I got the blue/black big hat sears one and thought it would be cool to have the Avocado colored one too. I know the frosted glass is pricey as well. I'm new into this so just asking anyone who is in to these as well.
@@gavinchang55 Follow up: The lady messaged me after not being able to sell it. I got this exact lantern & another Coleman 220F with parts safe that had tools, mantles & new generator. I paid $80 for both! The Sears has a few blemishes but besides that is perfect. It's by far my favorite lantern I own now.
To much dead time...stopped watching at 3;00 scratched the fuck out of that valve stem....don't do it the way he did
I have same problem removing old packing from inside nut but don't understand what you said. How did you remove packing from but and not damage but threads?
Just dig it out slowly and carefully with a small file.
@@gavinchang55 太感谢了
@@a3a14613 哈哈~~不用客氣
Where can I get a set of those molds ?
Hello.. I have provided the file link, but you need to use 3d printer to make it yourself
what kind of paper?
Coffee filter paper
Chang 大 你好 謝謝你 的200A影片 讓我們受益良多 大大 能幫介紹在那裡買200A 零件 的地方嗎
很高興影片對你有小小幫助囉 零件應該蝦皮都有,也可以參考我的賣場唷... shopee.tw/gavinchang55?categoryId=100637&entryPoint=ShopByPDP&itemId=21761573990&upstream=search
請問是用什麼餌
葡萄，小番茄....不能用活餌
I gave up at 2:12 since much as I like in-focus sunflower tiles I learned nothing from the blurry failed close-ups. I can't believe that at no time over the last 2 years you've considered making an in-focus version.
Gavin that is kool 😎
Gavin can I purchase some leather pump cups from you sir.
Did you use coleman fuel? Or gasoline?
I use white gas
That valve packing either needs to be changed or you need to loosen the nut
Those shades look like globes from Coleman lanterns??? What models??? Wish I could get my 132A running. It has a split tube just blow the valve assembly. The split in the tube is about an inch long. W Rusty Lane K9POW in eastern Tennessee
Coleman globe #355
What is the protection part used for ? And how do you use it? Your not using it in your video. Could you explain.
The protection part can protect the oump cup from changing shape.. before you use it
What kind of fuel does this use?
White gas
請問一下我是新手 綁燈芯有什麼訣竅嗎 我燒完燈芯 結果變成橢圓原型 不是漂亮的花苞型
綁好皺褶拉平均，燒燈蕊後第一次點時把氣打飽，這樣比較能把燈蕊衝撐，至於什麼形狀就要看你的燈蕊是長還是圓了
想請問前輩~小紅帽的空氣U管跟燈架~要怎麼處理才可以讓他回到亮亮的樣子
說錯了~不是燈架~是燃燒室的架子
U型管及銅管可以用鋁圈清洗劑泡一段時間後就可以除掉表面髒污,如果很髒就先烤過再泡,泡完用鋼絲絨推一下就很亮了,燃燒室如果生鏽是沒辦法恢復原本的樣子的(除非重新電鍍)..一樣泡鋁圈清洗劑可以除鏽
@@gavinchang55 謝謝前輩~剛好我是做汽車美容的~這幾天馬上試試
what kind of fuel are you using?
White gas
@@gavinchang55 Thank you for your reply! I'll check out your other videos too!
@@元アメリカ人 Welcome
What's the stats on how dangerous it is? Will it burst? How much would you have to use it before it gives up it's structural integrity?
In the correct operation, it is very safe
@@gavinchang55 pumping actions scares me. I guess it's not for daily home use.
@@Sohailali1 This is a World War II military stove , can now be used to make water and coffee while camping
Just came across your nice vidéo. Nice music too 👍. Have two Coleman, one Petromax and lately purchased one of those marvel of a lantern. Still waiting for it to arrive. I use them all in my RV for lighting and heating as well.... With a BIIIG fire extinguisher nearby of course.😁
Awesome..safety is the most important thing