Відео

That was a fun day!

Will it work on the chevy V8 5.7l 1990 engine.

Thank you so much

Blizzaks are the absolute best, I’ve gone 2 winters and I get better traction than most other cars out there. And I don’t even need sand bags!!!!

That’s sweet, thanks for showing me how! I have a navy blue 1999 V6 as well👍

Has anyone checked the connector at the back of the truck (right before the T), that comes from the front of the truck? There are 4 wires (ie 4 sockets to check for power). Can someone identify which wire does what? I get no power from the light green one....

Bad connection.

Thurman Merman all grown up

You could could have ran 2.5 inch pipe all the way to your back bumper with turn downs on them single chambers and changed up your whole tone and sound ...

WS6 Trans am was the most aggressive looking car of the late 90's and early 2000s. I'm dailying my 97 Z28 and its comfortable and fairly quiet.

I have replaced mine twice from two different company's. will work for a month then stop working agian.

Just a bad connection to battery. Clean cables.

1991 Chevy Silverado 1500 2WD. I have running lights, backup lights and both turn signals working. But no break lights and no emergency flasher lights. Already replaced brake switch, fuses and bulbs. Still no brake lights. No bad grounds found. We have tried just about everything we can think of. We need the break lights to pass the inspection. Do turn signal lights and brake lights share the same circuit on older vehicles? Could it be a bad turn signal switch even though the turn signals work fine?

Sounds good.

Cool fix. I had the same problem. But all I did was flip the fork around and threaded it back on. So it looks like the fork is upside down.

You can weld the stainless mufflers to regular exhaust pipe. Only difference is the weld will eventually rust like mild steel does vs stainless. Just spray the weld with some exhaust paint and your good to go.

Thank's for your cooperation

Drill little hole above brake light bulb and below break light bulb, then install small screws through board and tighten the screws down, make sure you don't drill through the rails running to the bulbs. 89 K1500 did this 8 years ago, no more problems...

i tried this trick but my heavy BBC springs keep bending them back ...... mines a MOROSO tool but they are the same

It's still cheap so it's not that bad just adjust the forks.

Are the mufflers and the dumps legal? And do you still have them? And do you like them?

if you drive in proper winters; do no get performance winter tires, there is still a big difference between the performance winter and proper winter tires in traction; noticeable in a car with much less low end torque (RX-8). Performance winters feel more like a top performing all-season instead of a winter tire. Tires are everything if you regularly drive on snow and ice. If all you get is a light dusting and you don't get slushy/ice/snowy intersections, backroads, etc. ... performance winters are probably best for you if not a top end all season set.

Excellent!

Great video guys! Great info and love seeing the younger guys enjoying the forth gens. I love mine!

Is that tool even designed to work on a Vortec ?

long shot on this but what traction bars are those? my 37 needs some help and would like the front mount to attach to spring perch like that.

Built 6.o in the 99 z28 straight pipe daily Florida life she loves takin sht stangs to gapplebees

Where can i buy the cap for my blazer ???

Thank you so much, used electric tape to create pressure and boom!!! It worked but going to buy circuit board thank you so much from me and my 1992 chevy 2500

Did I miss the part where you showed us how to fix it?

I bought my '00 Z28 in '09 I daily drive it rain or shine and when it ever does show here I still do ... .

Man, miss driving my 99 blazer. Needs a engine overhaul. Just driving my ss camaro now..

I bought a brand new TYC assembly and the board initially didn't have a back up light until I pressed in that same spot between the back up and center light like you show at 2:20. Mine stayed working when I released it though. Almost like the "wiring" strips that they use on the boards is only connected by the front and back boards being assembled tightly enough! Had one for the other side that several lights wouldn't work no matter what I seemed to do. I'm thinking about drilling out the plastic welds and soldering things together, the either re-plastic weld or just a button head screw and nut so I can take apart later if it has problems again. What a sh!tty design.

The tool is a great tool when it is adjusted correctly. With all the comments made about the fork angle, I am a bit surprised that Summit has not fixed this issue!

How can you not be freezing ??? Than again am from Florida....

Awesome ZR2.... Love the ones with the rear mounted tire carrier.

Wow ran away from the noise is that music?

Had my 383 made into a 496 back in 2008 by them they did a fabulous job. Motor still runs excellent. Made 610 ft/lbs torque and 555 HP on 91 octane fuel.

I hate the idle flub flub of a Chevy V8. That's what drove me nuts about my 2010 Camaro even with a stage 2 cam, supercharger and straight exhaust with an X-pipe. Now I have a 2013 Maserati Granturismo and you can't beat the exhaust note.

I'm a Camaro guy thru and thru. But I love the 98 - 02 firebird formula frontend! Looks way better and more unique than the trans am. Got to love the pop up headlights also.

Great sports car that’s American? You do know the 4th gen F-Bodies were made in CANADA, right?

Thanks for this. I just bought this tool and it came with no instructions. From your video I can see how to use it and lock it and what to look for as far as centering the fork to get the keepers on. I will try on my Ford 289 with stud rockers.

Looks like the same issue with a ‘92 Silverado Step-side. Sitting in the garage, the lights work as they should; out driving (bouncing around) when either turn signal is selected, both tail lights flash. Bad board?

What brand and size are the wheels?

I drive my 96 Formula except during rain. The only reason I do not drive it then is I live on a dirt road

In

It sound good. Just order the same flow master, I’m putting it in on my 2013 Tahoe

Thurman Merman? Is that you?

Nice video. I just don’t understand why anybody even disliked it

Definitely deeper after!