- 23
- 29 844
Øystein Eek
Приєднався 4 жов 2014
I'm rebuilding a Knarr wooden sailboat. The boat is built in 1950 and owned by me since 2003. In 2006 I slowly began the restoration. But in 2014 I ran out of time and the boat was put to storage behind a barn and forgotten for 7 years. But now I'm determined to complete the restoration.
Risør Trebåtfestival
Noen bilder fra Risør Trebåtfestival torsdag 08.08.2024. Jeg håper å være der med egen båt neste år. Følg gjerne restaureringen av båten på denne kanalen.
Переглядів: 270
Відео
Moving day. Ep. 11
Переглядів 357Місяць тому
On the road and in the air, but still not in the water. Til lands og i lufta, men fortsatt ikke på vannet.
Replacing one plank on my wooden sailboat. Bytting av en enkel bordgang på trebåt EP.10)
Переглядів 1,1 тис.7 місяців тому
How to replace a single plank on a carvel planker boat. Hvordan bytte et enkelt bord på slettbygd trebåt.
Fitting a new plank on my wooden sailboat (Ep.9)
Переглядів 1,1 тис.8 місяців тому
Fitting the shutter plank on my wooden sailboat.
(Ep.8) Pusse og olje innvendig I båten. Sanding and oiling innside of the boat
Переглядів 1,4 тис.8 місяців тому
Pussing og impregnering av innsiden av båten. Båten har vært lagret delvis ute i mange år og alt har blitt grått og trist. Sanding and sealing inside of the hull. The boat was stored partly outside for several years and everything has turned sad and grey.
New Garboards on my wooden sailboat, Nye kjølbord (Vannskrekk Ep7)
Переглядів 862Рік тому
Replacing the garboards on my Knarr wooden sailboat. (Vannskrekk Ep.7) Nye kjølbord på min Knarr treseilbåt. On facebook: Seilbåten Vannskrekk groups/488542688896255
Centering and bolting the keel Restoring a wooden sailboat Knarr ON42 Ep.6. Montering av jernkjølen
Переглядів 3 тис.2 роки тому
This video is about refitting the cast iron keel with new keel bolts on a wooden Knarr sailboat. And doing the right measurments to get it in the right position. Denne videoen handler om å feste jernkjølen til båten med nye kjølbolter på en Knarr treseilbåt. Og måle opp båten slik at kjølen kommer riktig på plass.
Replacing the floor timbers. Restoring a wooden sailboat (KNARR ON42). Ep.5. Nye bunnstokker.
Переглядів 10 тис.2 роки тому
In this video I make new laminated floor timbers for my Knarr wooden sailboat. The boat has been on land for 17 years now. In the first years I replaced 58 ribs, the keel timber and a few floor timbers. Then the boat was put in storage behind a barn for 7 years. And my wife nicknamed it "Vannskrekk" (Fear of the Water"). But now I'm going to complete the restoration. I denne videoen lager jeg n...
Seilbåten Vannskrekk Ep.4. Restaurering av Knarr ON42. Utbedring av tørkesprekker
Переглядів 4,5 тис.2 роки тому
In this video I'm repairing the dried out cracks in the keeltimber on my Knarr wooden sailboat. I'm routing a groove and glue in some battens. The boat has been on land for 17 years now. In the first years I replaced 58 ribs, the keel timber and a few floor timbers. Then the boat was put in storage behind a barn for 7 years. And my wife nicknamed it "Vannskrekk" (Fear of the Water"). But now I'...
Steam bending the keel timber. Dampbøying av kjølstokk. Restaurering av Knarr. Vannskrekk Ep. 3
Переглядів 8942 роки тому
Knarren O N 42 får ny kjølstokk. Dampbøying av eikestokk over jigg. The wooden Knarr sailboat gets a new keel timber. Steam bending oak timber on a jig. Musikk: Mini Vandals - Sam the Man
Seilbåten Vannskrekk Ep.2.
Переглядів 1,3 тис.3 роки тому
Restaurering av en Knarr seilbåt. Seilbåten Vannskrekk har stått på land siden høsten 2004. Den har fått ny kjølstokk, 58 nye ribber og nye bunnstokker. Men så har den stått lagret under lekk presenning i 8 år. Denne videoen viser hva som må gjøres for å få Vannskrekk ut på vannet igjen.
Seilbåten Vannskrekk Episode 1
Переглядів 1,3 тис.3 роки тому
Seilbåten Vannskrekk flyttes fra dvalen bak låven og inn i egnet lokale. Båten er en Knarr med nr ON42 bygget i 1950.
Knarr ON42 Restaurering. Første gjensyn.
Переглядів 9693 роки тому
Restaureringen stoppet opp etter mange års jobbing. Båten ble satt til langtidslagring fordi jeg var lei, og jeg måtte starte renoveringen av huset vi bor i. Nå er det nesten ferdig og jeg har overskudd til å starte på båten igjen. Her er første gjensyn etter 6-7 år under presenning.
La vie en rose Anita Torvund Ælvespeilet
Переглядів 5477 років тому
La vie en rose Anita Torvund Ælvespeilet
L'hymne de l'amour Anita Torvund Ælvespeilet
Переглядів 5537 років тому
L'hymne de l'amour Anita Torvund Ælvespeilet
Les trois cloches Anita Torvund og Gladurjentene
Переглядів 3747 років тому
Les trois cloches Anita Torvund og Gladurjentene
Nice to see it progressing :-)
Beautiful Knarr!!!
@@saabtech3510 Thank you!
Hi, found your channel as im about to restore a similar swedish sailboat. what the best process to hide the bolts?wood peg?
Pegs, plugs or bungs. Depends what you call it. Check out this video, and you know what to do. Good luck with your boat. ua-cam.com/video/v9m73_H8TCc/v-deo.htmlsi=3eeSW2mMMXSmOL0f
Thanks for the hint. Would you do also inside? Or just in the outer planks. Just had a look at this video and seems they've done also in the ribs ua-cam.com/video/Jz2m0s3XuVU/v-deo.htmlsi=TXQQNUNfBJP5q5zW
I just found your channel and have watched all of your boat restoration videos, thanks for posting them. I really like how you do your work. What wood are you using for the planks? And thanks for adding the English subtitles.
Thanks! I'm using pine wood for the planks. The boat is built with Oregon Pine planking or Douglas Fir as you may call it. But it's too expencive and the Norwegian Pine wood is a good replacement.
Heisann morfaren min døde nydelig og han var veldig glad i tre båt og jeg har blitt interessert i det nå dessverre kan jeg ikke spør han om spørsmål lenger 😢 så jeg er så glad for at du har lagt disse videoene så kan hjelpe meg tusen takk og lykke til videre jeg gleder meg til å se neste video
Hei Trist å høre at morfaren din er gått bort. Morfaren min døde for 10 år siden, og faktisk hadde jeg båten i hagen hans når jeg startet restaureringen. Han var gammel fisker og hadde jo mange gode tips om trebåter. Takk for at du så på videoen min, vi sees i neste 😀
Good to see you are up to speed with the yacht. It’s really interesting to follow your work. Lycka till 2024!
Beautifully done with care and attention. Are you happy with stainless screws or will you be using silicon bronze? I know which is more economical. Happy New Year! Regards Peter
Happy new year ! These screws are bought many years ago, and I can't afford to buy 2000 silicon bronze screws. And every screw in this boat is A4 (316) stainless steel.
Beautiful work. Impressively thorough!
U r the man!
Wonderful! Thank you for sharing.
I have been in the boating industry in the USA my whole life, love to see the rebuild of an old wooden boat. I was extremely disappointed to see you using Stainless Steel fasteners in this boat, more importantly Stainless Steel sheet metal screws. Given the age of this boat I have to assume it was originally fastened with silicone bronze wood screws or copper rivets ?
Originally the planking was fastened with brass screws over the waterline, and steel( not stainless) below the waterline. This caused a lot of damage when they rusted. I had to replace 60 ribs. I'd like to use bronze screws and bolts all over, but it's too expencive. So I use Stainless A4/ 316 screws and bolts throughout the hole boat. And I can by them at the local store.
My father and I restored a 1958 mahogany Knarr in the 1970's. Beautiful boat! Sadly, after 2 years of sailing her, a tree fell on the Knarr, in the boatyard. She sits on the bottom of Lake Ontario now. I am so happy you are saving this one!
why are you not using Brass screws ??
Brass not very long lasting in sea water. Bronze would be the best choice. The next best is sea water proof stainless steel . Wich I startet with many years ago because it's less expencive. And now, I will use only that because mixing with other materials will cause galvanic corrosion.
Veldig bra Øystein, alltid kjekt å se på dyktige håndverkere!
Takk, Pål!
Underbar vacker sångröst din kone har. Lycka till med projektet.
A sweet boat ! ~ Such a sweet spot to work ! ~. Such sweet singing ! ~ Such technical skill and knowledge ! ~ Thank you (both) so much !
Thank you!
Imponerende arbeid og ikke minst pågangsmot. Gleder meg til fortsettelsen. Var det Edith Piaf til arbeidet?
Ja det var Edit Piaf 😀
Imponerende - og kjekt med musikk te ærbe;)
Ja, ikke sant. Synd hun ikke er med hver dag 😀⛵️
Hey Øystein, thanks for including the subtitles so I can follow along. Loving watching you bring "Vannskrekk" back to life. Keep on keeping on and she'll be ready for next season 🤞🏻🙂Beautiful singing by your wife, sounded so good in that big space👍🏻
Thanks a lot! I will keep on.
Dish du bul sey te fo sick se mo!
I'm very impressed with your chosen bending technique. That short video makes subscribing a must. Great work!
Thank you. The forklift was there. So why not use it. 😀
Beautiful boat, the building and its other contents look interesting too. When you need some real power it's hard to beat hydraulics, brilliantly done!
I like the laminated floors a very practical solution was that epoxy or urethane adhesive ?
I used polyurethane. Too cold for epoxy in my workshop in the winter. And with PU you don't need to dry the boards after steaming.
@@ysteineek3976 PU is a great option with those constraints I sort of guessed with the foamy extrusions. PU is more waterproof than epoxy but epoxy is stronger and more tolerant of woods movement I use both in my boat building workshop. Epoxy is first preference though I guess it has a longer history of use whereas moisture cure PU is new technology.
Subscribed and looking forward to more of your videos sir. Noticed you have a bandsaw. May I suggest searching for a resaw blade that will fit you bandsaw? We have a bandsaw from Grizzly that will resaw 10 inches of oak with no drift and that is with a standard blade.
Thank you for subscribing. I know the bandsaw has a wrong blade. It belongs to the workshop next door and I didn't have time to by them a new one. I'll check out Grizzly.
Brillant bending method.
Greetings from Whidbey Island, Washington State, USA. Well done, sir. I've subscribed and look forward to your future videos.
Thank you!
Nicely done!
Thank you!
Thank you!
you beaut!
Veldig kjekt å se at du gjør så grundig arbeid med restaureringen av båten din . Flott video
Takk for det.
Er planen å få den på vannet så snart det lar seg gjøre? Eller er dette vedlikeholdsarbeid for enda flere år på land ;)?
Planen er å få den flytende neste år. Men det er litt avhengig av tilstanden på dekket. Hvis jeg må ta det også går det nok en vinter til. Men jeg mest lyst til å sette den på vannet en sesong eller to, og så restaurere dekket senere.
Gleder meg til neste episode :) bra at du viser så detaljert hva som må gjøres (y)
Hvor mange timer antar at trengs for å få den på vannet?
Umulig å svare på. Heldigvis 😅
👍🏼
Godt stroppen holdt😳
Ett godt utgangspunkt det der
Gleder meg til å se prosessen🤩
Hello! Well done! To sing in french is difficult. Good performance! I appreciate. I have made a cover of this song on my channel, for 4 trumpets. Greetings from France!