Відео

You keep saying 'solvent' but haven't said what type of solvent you are using. Also, I am assuming what you call 'minersl spirits' is also called 'white spirits'

One thing I suggest not doing when u use air. If u ever want to change grips and the one your changing u want to save, don't poke a hole through the end of your grip (as u see him do). Reason, poking a hole will send air down the saft, instead of flowing around the grip. Thus making it really hard to remove if u want to save the grip.

Ben, you do the very best video instruction I have seen, great job thank you and I have shared your videos with other golf nuts like me. Thanks again

Possibly a stupid question, but can the stamps wear out after extensive use?

Dude. So sick. The blue trim around the black might be my favorite accent

What is the green tip on the end of the air gun and where do I purchase?

Water and few drops of dish soap?

I enjoyed your Video. Well Done! My Wife loved the Music and so did I. It was entertaining. Don't listen to the old Curmudgeons.

Where to buy buffing kit

Air may be free but the compressor is really expensive. Solvent and a $5 spray bottle from the Dollar Store (plug). Cheap, effective, arrives at your door in 24 hours.

Great video ... can you by any chance tell me the letter size and letter type on the Vokey Vedge - Impossible/possible? Thank you ...

What does the bending do?

Are you using acetone immediately on the shop rag to wipe off the excess?

Only 30 seconds im and already love this

Why do you poke the end of the grip? Surely all sorts of dirt and muck can get in, causing rattles?

The think that you are missing is water with a little dishwashing soap. And a properly is going to use mineralspiret when a will regreap my clubs. I have no compressor, and have the sperit standing around. So thanks for the info

Have you tried soap water?

Does mineral spirits mess up the paint on a graphite shaft?

Hello, how do you remove the glue underneath the ferrule? 2:56

Try using charcoal lighter fluid. Been using it for years. Work great.

I am satisfied in knowing my becu eye 2’s are and will always be the best irons made. I’ve had mine since highschool in the 90’s and I’ve used pxg, newer pings, titliest, you name it. Nothing compares to the feel and the range my copper eye 2’s have

how stupid would it be to attempt to stamp on a Ping G425 3 Iron crossover after a ton of practice on junker clubs, if so where would you suggest stamping ? Also love the vids prob the only ones I have found that are in depth.

Great video full of info. Love you’re delivery and humor 👏🏼🙏🏼💪🏼

I noticed that you puncture the end of the grip after installing it. Why do you do it? Thank you.

I use spray paint on my motorcycle grips and it works fantastic

What’s the stamp size of the “impossible possible” lettering?

What is the purpose of "poking" the end after the grip goes on?

Please reduce the Music Volume I have had to turn it down 25%

Ping ISI's don't require ferrules. They work you did is nice as I do the same thing but the ferrules have to go, lol. Just not right on those Ping irons !

so did you not use double sided tape?

HF-100 is totally awesome and you only need a light mist from a pump sprayer. It's like cologne. Just do a few sprays on the taped shaft over your bathroom sink and the grips slide on super easy. I did all mine by hand, no stupid vice or fancy drip tray. If you're dripping solvent you've used way too much. The little bottle that came with my grips is probably enough to last me the next decade. It's only like a few bucks shipped--- all these other inferior solvents and your dish soap are way more expensive.

Isopropyl 99% you think it’s similar to mineral spirits

Ever try soapy water just add a few drops of dawn dish soap to a spray bottle full of water

Your content is great! Thank you for not putting it behind a paywall. Keep up the good work!

Great review! Thanks for sharing!

What do you use for the paintfill?

If you do air can you remove them with air after a year of using?

You need that little air adapter thing you used though

Good video ruined by poor choice of music and loud as hell!

Where can you get engraving done? If it has not been done at the factory?

Is white spirit a mineral spirit?

'Promosm' 🌹

Good info, well presented. Thanks man!

Brilliant vid…. Thank you! 👍

Great irons brought back to life! Thanks for sharing!

What is the growth in your left hand

I use air with water for some lub it’s easy on and dries quickly

Seemed to be making it hard work and a mess better videos out there and easier processes

Thank you for sharing and I've been using the air and water and it works too.

Thanks for the video, I just regripped a driver and almost didn't get it on Tip.......don't wear rubber gloves they just slip on the grip as you push....paper towel like you used works out well..