Відео

Thx very good !

size nut for Bilstein B6 nylon locknut?

Hey Ken. iDrive knob stop working after i assembled everything together. Prior to that when i tested it worked fine. Do you know what could be the reason? Thanks!

Ottima spiegazione grazie di averlo condiviso 🎉🎉🎉

How are these X1's with the B48 holding up Ken? any major issues so far?

Hope I can fix it the same too...thanks for sharing

did it, working very well, many thanks for you!

Hi bimmers its copied from new TIS BMW HOW THE SERVICE MUST BE DONE . Checking/topping up oil level in automatic transmission (AISIN F22AW) Top up transmission oil. (Transmission oil has been drained) Release oil filler plug (1) from engine compartment. Tightening torque 24 11 3AZ. Loosen the overflow plug (2) below at the transmission. Tightening torque 24 11 2AZ. Top up automatic transmission fluid at oil filler plug (1) until oil emerges at overflow plug (2). Start engine and run at idle speed. Check whether automatic transmission fluid emerges at overflow plug (2). If not, fill automatic transmission fluid. Actuate footbrake and at idle shift through all gears ("P" to "D") twice for more than 2 seconds. Then set switch to "P". Check again whether automatic transmission fluid emerges at overflow plug. Check the temperature of the automatic transmission fluid with the diagnosis system. Increase temperature of automatic transmission fluid to 35 ... 45 °C. Top up automatic transmission fluid until it flows over. Screw in oil filler plug (1) and overflow plug (2). Tightening torque 24 11 2/3AZ. Installation note: Parts: Renew sealing rings. Check oil level (transmission oil temperature must be between 35 and 45°C): Undo oil filler plug (1). Slacken overflow plug (2). Tightening torque 24 11 2/3AZ. Start engine and run at idle speed. Unscrew overflow plug (2). Check whether automatic transmission fluid emerges at overflow plug (2). If not, fill automatic transmission fluid at the oil filler plug (1). Top up automatic transmission fluid until it overflows at overflow plug (2). Actuate footbrake and at idle shift through all gears "P" to "D" twice for more than 2 seconds. Move switch to "P" position. Check oil level again. Seal screws when the oil emerges slightly from overflow plug (2). Tightening torque 24 11 2/3AZ. Installation note: Parts: Renew sealing rings.

You unbox 75 inch by yourself? I unboxed 55 inch myself wiiiiiith my 4 sister and mom. 😂❤

Idk why but the paper won’t go down at all. Am I using the wrong paper? On the left side of all my digit slots there looks like there is something in the way of allowing the lock to reach the bottom of the wheel. Can I use the right side of the digit wheels?

Brilliant video. Had a Krups Expert machine that I had stored while trying out a new Vertuo model. Decided to go back to the Expert but ended up with all the coffee going into the capsule drawer. Thought I was going to have to bin the machine. Followed your video and discovered dried up coffee was blocking everything. Had a couple of problems fitting back in that extra white part (it just sits underneath and in front of the white coffee dispenser part) and the getting the black top part where the capsule goes back on (there are little sleeves over the roller parts that had slipped to the edge of the machine, stopping me from pushing the part down onto the “rails”). I wouldn’t have had the confidence to do any of this without your video. Now everything is clean and working again. Thank you so much.

It is the front o2 sensor but he is saying it is after the cat?

This video made sense from beginning to end, really easy to follow, a solution that is helping countless people...well done!

I have been listening and watching others but this made absolute sense to me and worked the very first time. Thank you

Hey Ken. How much did it cost and from where did you purchase it? It looks like a higher quality head unit than the android ones from mekede. How do you like the linux unit? Thanks

Thank you. I have a machine which sometimes refuses to close. Nespresso sent me a new one and didn't ask for the old one back so I figured I'd try and troubleshoot it and fix it if I can then use it as a spare or bring it to work. But it was a mystery how to open it! Now I have it opened and can delve further.

Did you need fiber optic decoder box?

Youschud not put thisvideo on line , you put lives at risck speccialy old peplos , if this is true worck

Здравствуйте!скажите пожалуйста контрольный замер масла на заведенный двигатель и какое положение селектора передач должен стоять P или N?

Great video, thanks for posting it really helped me get mine installed on my 2016 X1 F48. Couple of things I missed for others giving this a go; The original cable with the purple connectors needs to be reused. In rewatching I see you kept it but I missed that first time round. I also had to change the iDrive generation to a different setting than the one I thought I had (thought mine was NBT, but turns out it is CIC - type 2 in the instructions). Finally the Aux cable did not need to be plugged into the remote Aux port if the car, I just left it connected to the internal wiring harness. My unit came from AliExpress, was about AU$380. Works really well, can use the mode button to switch to factory drive .

Hi, after how many minutes does the gearbox oil reach about 50 degrees Celsius? I don't have a tool to measure the temperature.

hey, can i use zf lifeguard fluid 8 for this car?

This should be removed.

This was the most helpful video ever. Super useful. I did have to rotate mine 5 to get the correct numbers

Although you have routed the cable behind the airbag modules, since you routed the rear camera cable through the door seal and trim, if the curtain airbags are deployed, this cable could quickly hit the passengers and cause serious injuries. Is there a way to prevent this? Or do you think you have prevented this? One way would be to route it from the bottom, but I don't know if the rear camera cable would be long enough.

Great video bro

Thank you for showing where the drains exit the car. Squeezing the grommet is a great tip!

Hello, great video! I have the same car a BMW X25 Xdrive from 2016, in the BMW ISTA documentation it says to open the oil level screw between 35 and 45 degrees Celsius, is that right? Do you plan to drain the transfer case and the rear axle on this model? Best regards, Serge

Such a helpful video! Thankyou! I have found on my Right Hand drive GLc there is a small fuseboard on the drivers side of the dash. One half of it is permanent live, the other half is switched live! Very convenient

works lol

Yesterday my coworker set the code and then promptly forgot it. We had to get the box installed the same day. This video helped me open the box - thank you very much!

Thank you for the video, I have the exact problem and need to do this right now. Wish me luck :D

It works, thank you ❤

Thank u

Work like magic late

5 on it

When paper drops you got code

This how you do it orgamie paper

you didnt show how to move away positive terminal battery. Because cable arent allowed to take it away. I notice you unscrew . But how you did it?

very helpful, thanks. of course the most difficult part is the PULLING OF THE PANEL OUT OF THE WAY and how to do that with the 12v outlet and tie-down bar locked into place. but I have a 2014 and maybe they decided to make all this more difficult.

Thank you very much! I just finish the gearbox oil change. Your Video is very helpful. Gerbox oil Bmw ATF6

Very useful. ❤

Great presentation. Thank you so much.

Great presentation. Thank you so much.

Thanks, it worked.

Thank you so much for the advice

Hi, does the car have to be on a lift (wheels up) to be able to change gears during an oil change?

So , 2tb are supported? With single side nvme ?

I want a tv with the best picture quality

Very helpful video! I think I can DIY now!