Відео

Yessir!!! Old skool putty 💯🤙

Watch the beginning it shows how to tell which wires go to the heater.

12 v 24 v 220 v 10 watt 150 degree.............ua-cam.com/video/sb49Jkz6P54/v-deo.html

By far the best video I have watched

Great refresher lesson! Thanks for the post!

Now the question is how do you remove an old sink like this??

Good job and video

Great job

Best video I found. Well done thanks saved my bacon!

Dude is a pro’s pro! Thx!

Thank you for this video...but would like to learn more..

Crazy that after searching online for days, this is the video that best explains this concept.

What about showing how to make the measurements for centering drain tailpiece on drain plumbing and to make the measurements for centering china sink on the laminate countertop, or with respect to center of the cabinet below? What do you do to remove sink from countertop, when you've used so much caulk under edge of the china sink, to hold it in position? Versus, six points of caulk, between 3 and 9 o'clock with faucet at 12, to hold in place, which can later be undercut with sonicrafter or similar? I just replaced a master bath sink and regret using more six points of caulf, versus your whole ring, as I did 25 years ago, too.

CERAMIC SINK IS NOT A STEEL PORCELAIN SINK. WRONG DESCRIPTION.

What is wrong my hot wires beep with the ohms meter???????

Great video! Direct and to the point.

Easy because Is not real granite, o😅

Great explanation, great camera angle, thanks for the info

Ron we need more videos brother

Thank you for the video. Is the flanged tailpiece that goes into the disposal polypropylene or ABS or does it not matter?

Usually, black goes to line and red goes to load. In some cases, wiring a device backwards as he does here could cause problems. Always read the instructions that come with your device. Even electricians get cocky and lazy sometimes.

Thank you very much! I will take it in consideration. 👩🏻‍🌾

Just the video I was looking for.

So it has to be feeding another thermostat on the other side because you need a double pole breaker, correct?

Thank you!

Nice through 😊job !!!

Shouldn’t you use a wet towel? I mean it comes off a lot easier. A wet sponge even better

I just had a sink installed in my kitchen the exact same type that is in your video. The guy claims he has 20 years experience I can't tell from the work that she done this thing was not screw clamp down underneath like you showed it out used the plumbers putty around the edges to keep water leaking in between the Carter board which it did and it started to buckle up and nor did she clean up behind himself dorota complained to his his company thank you for that video it was very educational and I will use it in my complaint against the guy that installed like he's sick keep up the good work

You did an excellent job explaining step-by-step on how to get stomach sick correctly 7:40

Good on you for cleaning up after yourself. I had a guy install carpet on my stairs, left a huge mess behind and even recommended I use a shop vac to clean it. He left me his card and said if I ever needed any more work done to give him a call. Needless to say I won't be calling him.

Thanks. Makes sense about the silicone caulk!

You know how to instruct people who’s waches your videos I think is the first feed back I been given greed job been looking for these video, other people they just wanna be showing what type of job their doing they don’t explain Great Job

None of mine beep when I'm on Ohms audio. It beeps when the probes touch each other but not when I touch the wires.

Theme was wiring two pole. Wasted too much time on general wiring techniques. Can watch videos for that if we want to learn that.

Thank you!! For your helpful information and very good attitude, it will help me to know how to put my sink into my new counter top and cutting it myself, I have been puzzled 😕 for a year now because I really thought I would mess it up . I appreciate your video and thanks a million times.

OL means open loop?

I can’t find that snap on tool anywhere

What size of hole saw did you use?.

Thumbs down for loud music at the start

You cannot always go by the wire color on the thermostat. I had to make sure T1and T2 on the thermostat went to the baseboard heater and L1 and L2 on the thermostat went to the input power. The house circuit breaker tripped when just using both black wires on the thermostat hooked to the baseboard heater.

Btch wanna ride btch wanna imma jakdassoff and i still aday Hit it again with the wain and the gain

You didn’t show what you connected the red wire to

When setting the sink do you use silicone?

I just put this same Cadet heater in the Double unit not the single like yours. Not working It's blowing out Cold Air Smh

My friend you saved me time and money I appreciate you....

Double pull

Omg thank you, you saved my night, because the day was entirely trying to wire it. Haha

Could you use a heat gun to help with that putty on cold days? This looks easier to do than I thought.

Great video man. To the point knowledgeable and nice clean work. Thank you good job. I subscribed

Mine has a black and red in Line1 and line2. A black and red in T1 and T2. I connected the hot black wire to the black wire on L1. I connected the incoming white wire neutral to L2. I connected the black wire going to the heater to the black wire on T1. I connected the white wire going to the heater to the red wire on T2. IT didn't work!!!!!!!!!! The heater started making a loud sound when I turned it on 😁😢 What did I do wrong??