Відео

Orange light represents Overload. Main Electric Assembly or Self-Propel may defective depend on which feature you activated.

@ for my 2130, it’s solid orange which shows a thermometer? But it doesn’t have self propel. The headlights work. The engine starts for a split second then shuts down the blade. I tried taking the blade off to see if it was under too much load and it still gave me the light.

@@CareySalander The orange light only indicates the mower is overloaded, not the thermometer, like a fault code. As it doesn't have a self-propel the main electrical assembly is likely to be defective. You can contact EGO customer service for assistance.

@ do you happen to have a video showing a diagnostic method for the switch assembly in the handle? There’s a small board in there and I have a gut feeling something isn’t quite right. Went through the whole diode diagnostics in the motor and main PCB compartment and everything is good.

@@CareySalander The only method to diagnose the switch assembly is the cross check. Replacing it with a new switch assembly.

Check out part list @ www.skil.com/10inch-dual-bevel-sliding-miter-saw-ms6305-00/

Part #2826622304

Hi there, please clamp with sharp-nosed pliers where the hand is held at 1:24 of the video and turn the blade-bolt-cover firmly clockwise

I just bought this saw. Brand new, not even powered on. Want to change the blade to an 80 tooth. I loosened the blade bolt cover screw per the directions, but I cannot get the blade guard to move back. I called SKIL for support, not much help there, other than to take it to a SKIL service center. Any ideas?

@@DavidGenrich I was eventually able to force mine back into place after much effort, force, and a little gear oil. You might try that. Either that or return the product as defective. I certainly thought about doing that. It should not take near the amount of time and effort to change a blade.

@@DavidGenrich I jiggled that little black plate back and forth over and over again and eventually it flipped up. Then to put it back, I had to hold that black plate down into place while tightening the screw.

@@wesbaumguardner8829 @steetsbolt I tried WD-40, I can't get it to move at all. I can't wiggle it, since there is no play in it - almost like it is glued, or painted, to the motor housing.

That tire will last a verrrrry long time. I agree this is a pain, but it's not exactly complicated. Have you ever seen how you need to replace the drive belt on a Harley? The air filter on most modern bikes? If this seems daunting, hiring sombody to do it 3x over the next 10 years this bike might last, isn't that big a deal

The motor is in the tire, so there's no chain running through the bike. It's a trade-off. Makes it light weight, it requires less maintenance, and it creates more space for storage. It just depends on what your preference is.

When taking the blade off, make sure you are untightening the bolt clockwise. Note,,, "This is Not righty tighty, lefty loosey"😉

Front Brake Pads (1 Pair) 2851238001, Rear Brake Pads (1 Pair) 2851241001. You can always check out the parts diagram from: egopowerplus.com/mpattachment/file/download/id/3421/

My rear brake pads kind of scrape on the rotor.. I’m think the brakes aren’t straight or maybe to tightened ? I bought it brand new

How often should I replace

Nope.

Nope

Here you go. ua-cam.com/video/IxBNekWRiwU/v-deo.html

I think I've had the same problem. Did you call the customer support?

Make sure the tractor isn’t fully powered on (Do not press and hold the power button to turn it on, just quick press the power button once). While it’s off, quick press the power button once to display the battery percentage; try the update when it’s in that state.

Exactly. You have to download the Firmware first.

Here you go. ua-cam.com/video/IxBNekWRiwU/v-deo.html

@@trainingvideos4695 Thanks

Looks he just kept twisting the green knob until the chain was tight.

Please check out here: egopowerplus.com/mpattachment/file/download/id/3554/

@trainingvideos4695 Can I get the cable Diagram for the Z6 mower please

@@briankohlenberg please reach out to EGO Tech Support Team. They will give you the file you need.

Nope.

@trainingvideos4695 Wow, their most expensive walk behind is a single blade with the most torque and non whining self-propelled. Hard pass, single blade is trash. Ty

I don't understand this either

I thought the same thing, I didn't do it

I highly recommend trying it out at the shop