Відео

Amazing easy way to explain and teach thanks

(5:45) What ar the NO, NC, and COM terminals on the magnetic lock used for if the application switches power directly on terminals 1+2?

how do you do it

I need help wiring a keypad (advantage DKE 26-500) to a mag lock with push button (SD-7202GC-PTQ) if anybody know how i would appreciate the help.

We have same system but when we use a fab to get access it doesn't work unless someone push the button from the inside please what we should do. Your help will be appreciated thank you

I have an argument I, have had with our crew. dont twist wires counter clockwise when using wire nuts. either dont twist or twist clockwise then use the wire nut.. Otherwise you are untwisting the wire then retwisting it clockwise when twisting the wire nut on. Certainly Im not wrong am I? For me to be wrong would be unheard of. LOL

the best and easy to follow instruction!👍👍

can i have 2 exit button working with the same magnetic lock?

Is it possible to connect two rfid readers in parallel? ( for magnetic lock)

Why you splice the negative with common

If I skip everything but the power supply, magnetic lock , and push button any diagram on how to connect?

Why you connect the common with the negative please somebody explain me

Where does the no (normally closed) wire connect? From the controller and sensor?

Twisting the wires backwards, So much for wire nuts hahah

Is there anyway that these systems can be operated using a manual key? Turning the lock?

Would the buzzer work by connecting the positive of the buzzer to the positive of the mag ,and negative to normally open ?

How do you add the access codes to get access through the keypad

Does color of d cable matters when u connect eida NC or COM

Thank you, very much for your video. I have to install a similar system but I think the general concept will be very useful to me. Muchas gracias por tu video. Tengo que instalar un sistema similar, pero creo que el concepto general me será muy útil.

Will this work with a 12v or 18v power supply off of a Milwaukee battery pack?

Good day.. Will u help me install an X660 biometric door lock in step by step until registering fingerprints.. Thanks

Hello. I have magnetic locks that have status LED's. One lock shows red LED when the door is opened and green LED when the door is closed. This is the normal behaviour. However, for the other lock, LED remains red even when the door is locked. Do you know what may be happening here?

!Hola

ua-cam.com/video/wOxUBFbXUmY/v-deo.html Maglock troubleshooting

hey you think i could hook up an adrino and control it via wifi?

*>>>**t.co/Nmgemqcew3** As most have stated... the instructions are a little lacking..... Note the the brackets they give you for the Chain to connect to the gate will not fit 2" Steel pipe.... I had to modify / Weld mine in place*

Better to use a smart web power socket and UPS and bypass the timer and battery altogether. Can then be armed/disarmed via a phone and set on a schedule.

If no backup what will happen

why p0rn muzik?

hello ,,i have zkteco x7 ,,but i dont know how to installation to maglock,,,can you help me,,,

Hi. I recently purchased from your store here www.fastaccesssecurity.com/proddetail.asp?prod=FAS-PAWN-SHOP-MAGLOCK-KIT . I got some instructions but its not enough. Nowhere on the on the 2 papers with instructions is mentioned how to connect the different devices to each other. I got the one with a keypad for garage door, 2 remote, magnet and plates, Exit button and the receiver box.

can i get model number for parts you using and who sells these products

Informative, thanks I was wonder id that power wire with stripes

your PIR is wrong on your daisy chain, NC on receiver's output always goes to Common on your next device and not NC , also your exit button is momentary and needs to be a 30s delay on press to meet fire dept code, your wiring wont pass inspection

can i use a regular automotive battery on this. i have a quad battery and was wondering if i can use it for this system.

se ve que si esbueno

The only video that showed me what I needed to know. Thank you

how you can configure (set up ) the padlocks

what type of a wire you recommend ?

nice one. will like to work with your products.

hi brother please I need to install two biomatric readers

hi brother please I need to install two biomatric readers

What's the specification of your power supply? Beginner here :)

Thank Brother this is helpful for me n I want to know the other types of Biometrics

Nice Video

plz help me...

thx broo..but I want to know about bioentry w..urgently plz...00966536272325..plz sent me all information about this bioentry w..plz help me..

Hello. Can I use this lock in a wood sliding door?

Is this a backlit keypad ? Can be programable too ?

great video.