Відео

@@autolife4180 there manageable once you get use to working on them i been wrenching in dealership for 20yrs now

@@mohammada4315 no Nvh, I have nvh in bmr motor mounts and bmr suspension

Appreciate that, thanks for watching!

One toe bushing for left and right side

@ do you know the part number or have de link for the other bushing thats in the knuckle, by any chance?

@@dto8182 comes in a set of two

@@dto8182 I’ll send you the link

@@dto8182 www.americanmuscle.com/frpp-knuckle-toe-link-bearing-1516.html

Is that a fact sir

@Coy.ote5 yess sirr 💯 they unleashed the beast

I just removed the ecm and put the wiring harness to the side

@@michaelsean3579 good guess but nope

@@EdwardoAlvarezjr hardest put is getting the air out of coolant system. So top coolant reservoir screw cap back on and theres plastic bleeder screws grab flat or Phillips screwdriver 🪛 loosen it 4 turns start the vehicle heat on full blast and repeat this method

Yes sir need take 20 and turn it 2500

@@madmax4729 it will take about 4.5 hours max so make sure you have the tools to dot the job before start

@ thank you

@@madmax4729 your welcome

@@Coy.ote5 do you have a business contact number?

Do you have a business contact?

Exhaust setup is 1 7/8 headers paired with H-pipe with bullet dumps

@@savagediy8077 is there any noise at cold start, like a rattle then gets quiet but is still present

@@chrisdavis6253 I’m laid back I appreciate it

I have a feeling that this is a good idea for the future of the game and

@@neryidarodriguez7933 I agree

We got to get more testing done

@Coy.ote5 yess bec Smokey gonna be a beast once it's figured out track again .💨💨💨💨

@ yes sir

He sounds so sexy....

@@schorched1973 it’s the same has this in the video

@ Thanks man I appreciate the reply and am subscribing 👍🏻

@@schorched1973 thank you 🙏

@@sebastiantavarez3733 no oil change needed you going to top the coolant, turn the heater on, these bmw are electric water pump so at first you want see it flowing, it be pushing air out the coolant system, then it starts to flow, so once vehicle is at operating temp and blowing hot out the vents. Check your coolant reservoir and top check for leaks.

Your welcome 🙏

@@wrx_david2382 I appreciate it

@@TexasBornAgainTrucker bet

Four the last bolt it’s a challenge you’re going to need quarter inch extension gonna need a 10 mm socket due to the fact that it is a tight fit and make sure you have a swivel then you should be able to get to it

I end up removing the fender liner on that side to help me see the location and angle

@@Artjan1 McLeod rst twin disc about drop a video, installing a new,

Awesome, looking forward to it!​@@Coy.ote5

No more lock out issues plus I upgraded my shifter to a Barton that help has well

@@Coy.ote5 i hear the mcleod rst has a lot of chatter, is it really that bad?

@@Artjan1 it’s not that it’s only at low speeds it’s really not that noticeable once you had in car for couple of years

@@geo641 welcome

I need to put your daddy car on the track so I see where he stands

@Coy.ote5 change my bushings and change my shock

@ when you need it done and get the stuff

@@Jamie-ww3yz I’m tune by Lund it’s free

I’m tuned with palm beach dyno not sure they still do it

@Jamie-ww3yz it doesn’t hurt to ask, I’ll do some research right quick

@@truckingwithstanley624 they are three 10mm bolts that hold the heat shield on, then go underneath the vehicle remove 4 19mm bolts to the exhaust and catalytic converter. Then jump back to the top and support engine with jack and plywood on the oil pan, low it so you can remove six 13mm nuts.

@ thanks

@ another question how do you take out the rear catalytic converter that’s under the car connected to exhaust system

@@Coy.ote5 when you say low the engine don’t you jack the engine up with a jack? I’m confused

@ remove the engine mount and lower the engine so you have have clearance to get it from the top

@@Chaos1-2R no it had melted and was rattling and when from blowing ice cold to hot 🥵

@@victorcruz4224 it’s insane it’s louder in person

I return that sh.. back

@ bru im having that problem with no struts 😂😭i need some mf help

@@Car_nage just loosen the bolts and adjust and make sure you have the same clearance on both side