- 10
- 10 438
Uppermost
Приєднався 25 чер 2007
Відео
Kawasaki Bayou 220 Valve clearance inspection and adjustment #kawasaki #Bayou220 #atv
Переглядів 1,8 тис.8 місяців тому
Bayou 220 Kawasaki Valve clearance inspection and adjustment
How to wire an automotive OEM Style switch with a relay
Переглядів 250Рік тому
This video will show how to install a matching OEM style switch, and properly install with a Relay. #toyota #oem #rocklights #automotive #wiringharness #tundra #diodedynamics
How to leak check pressure test carrier bearing lower gear unit outboard Evinrude Johnson
Переглядів 89Рік тому
Installing brake bleeder pump to pressure test outboard lower gear unit and leak test with dish soap. I noticed some water in my gear oil while doing an oil change
How to Tap and Install a Helicoil thread repair
Переглядів 32Рік тому
How to install a Helicoil after a bolt head has broken off and shank cannot be cleanly extracted
Nilight wiring harness to ATV LED Light bar Sasquatch Switch
Переглядів 258Рік тому
How to wire an ATV Light bar harness, relay, from the 3 wire Nilight harness to the 4-wire switch. Switch light will only illuminate when pressed to "On" in this wiring configuration, so you won't drain the battery Nilight wiring harness for LED light bar: www.amazon.com/Nilight-Wiring-Harness-Switch-Warranty/dp/B071ZPX32N/ref=mp_s_a_1_2?crid=3P6PCY29HUGYU&keywords=Nilight - NI -WA 06 LED Light...
Bilstein 5100 rear shock bushing set-up install Toyota Tundra 2007 - 2021
Переглядів 6 тис.Рік тому
Bilstein 5100 rear shock sleeve for Toyota Tundra 2008-2021 www.summitracing.com/parts/BSN-E4R01Z008C34
Got quoted ~$780 to replace the ~$160 oem shock pair. Grabbed the 5100 rear set. This video will help, thank you !
is that plus install?
Yeah, but that was still after the $200 multipoint inspect
Dam it all adds up. How's the shock going I know it has to be worth it.@@MrAndroid1337
What does it mean if the tip dead center dot falls on the bottom every time
Excellent demonstration of how to check the valve clearance! Quick question, I have the oem service manual and for some reason it does not say to make sure it’s on the compression stroke when your aligned the (T) . I actually have 2003 bayou 250 which is basically exactly same as yours . I can’t imagine why you would not put it on the compression stroke like you mentioned. I’m doing this now or started it and I’m glad I pulled off the recoil pull start it was holding water because the drain was plugged with dirt .
thanks this was a good help on checking and the intake side was way off, the exhaust side was at 7 so i put it at 8
😮
I love you for this! Thank you!
Most come with new bushings.... If not it's a good idea to buy new ones, they're cheap. 😊
Thanks! Quick and to the point! Very clear on explanation. Helped me a lot. Hopefully I can get mine running again.
About yo try this tomorrow 😅
Is this required for 2000 - 2006 Tundras?
I am seriously ticked with Bilstein. I got 5100's for my 01 Tundra and their instructions explicitly state to NOT use a lower bushing. Then they had a diagram showing no lower bushing. 5 hours in 95 degree heat in my driveway and it clunks if I run over a minor crack in the road. Garbage instructions.
thank you. not allot about the rear shocks
mine came with new bushing and hardware
Where did you get that full length 2” spacer ?
Bilstein provides crap instructions and fails to provide fresh bushings for my 2005-06 Tundra as well. Thanks for video.
If you got fresh bushings, where??
@B Random Good question! I'm not checking until I have to. They would seem easy to find but...
@@gratefuldale117 yep, I've been looking myself and phew no easy task.
@@brandomguess Summit Racing has kits.
But you had the rubber bushings wrong . The Bilstein website has the instructions
This is good for 4Runners as well
Thanks brother! I'm going to install on my 07 SR5.
Que lugar hermoso.. donde queda? Saludos desde Chile 🇨🇱
North Idaho National Forests, United States