Відео

I'm guessing this is from the Russian tool repair manual?

No oe hechastes grasa dieléctrica¿?🤔 Saludos

TheBil

Saved me $$ and time thank you

I have like 4 dead M12 batteries I'm gonna try this on

0:45 I don’t speak chipmunk on helium

I think we need to review the definition of easy

welding master

What if I can’t tighten the Chuck to put an Alan key in there?

Caution, on some models I've had associates destroy the mode selector mechanism by using the impact driver to remove the chuck. There is usually a relative thin plate in the selection assembly that controls the shift between torque, drill and hammer, the impact driver has enough strength that it can bend or warp that mode selection plate, mode selection no longer works correctly and the torque settings are wrong. It can be corrected but it requires the gearbox to be torn down and rebuilt which is significant.

Did it fix the problem?

Today had a job to do with one of these and found the blade stuck tight and unable to swap. Couldn't remember if it was a reverse thread or not and didn't want to tighten it by mistake. Couldn't find out from any of the online manuals. You answered the question first 2 seconds of the video. Thanks!

Unfortunately owned by China 🇨🇳

The electric brake feature is problematic with these saw switches .bad design.

I'd say it's not a good repair. It will work. For some time. Mixing worn cells with new ones in a series connection is not a good idea - cells will wear differently. Good pack of series (SxPx) should be picked from same cells, preferably from same lot and even then checked for internal impedance. Especially for high power loads.

Thanks for the repair 👍

Good vid buddy. Haven’t watched fully yet but I was coring a whole with this drill and the core got stuck in the wall and the chuck couldn’t be reached. So I had to shake the drill violently to get it loose, and it bent the chuck slightly. Will this video teach me how to replace the chuck?

👍

Mines has burned varistor nd i cant tell what part num there are because it completed burned can u tell me the park num of it on urs?

Hello. Thanks for your video. Dear friend can you please put more light it's too dark .Thanks

it would be great, if you could share more details about the programmer and where to get it.

Hello can you share the tool used to unlock the BMS

What was the fix, did you replace something or just clean it and apply new grease. Maybe I missed something.

I'm starting a tool repair biz,,,hell no can't assemble that mess without a parts diagram, because? I didn't tear it down!

Hola, quise hacer lo mismo, pero vino distinto, como muestras en tu vídeo, será por el año 2023 q actualizaron? y no se como destaparlo y darle mantenimiento al switch. Espero puedas ayudarme con saludos desde Perú 👍

What are you spraying on the switch? I'm trying to fix some drills that had brushes ran down to nothing, but after replacing them,,& new plug-in? Nothing when I push the trigger😡

Really helpful! Be careful with the inset of the bearings and check that you hammer on the correct race. 😊

👍

Always wanted to know if this wasvpossible (well, obviously! But, worth it. Rather.) and any special non intuitive hangups?

Nice video! What time is part 2 comming out?

Dewalt screwed up with the DCH273. I have 2 i am repairinng. The motors on both had a fan issue where it is making contact and jamming in the motor. A screw driver and a good blow out with contact cleaner freed the motors. How exactly did the fan get jammed? Were they dropped? Was too much force exerted during operation, or did the motors overheat? It is a design flaw. Repairing both motors successfully has saved me over €300.

Buenas tienen algún vídeo de como hacer un soldador o es de fabrica saludos por apoyarnos con sus experiencias un abrazo de Guadalajara Zapopan Jalisco México a sus órdenes Agustín Hinojosa

👍

Silicone spray would help to put those cells easier 😀

so all you have saved from the old gun is the motor,the trigger and some wiring....may as well just buy a whole new gun

I😮

Hello, by your experience there is DDF484 is more strong than DHP484? I know that DHP has the hummer-drill function and DDF doesn`t but I don`t understand if there is any advantage about durability choicing the DDF over the DHP. Maybe using the hammer-drill function will wear sooner the system or so...I don`t know. Thanks in advance for your replay.

Hell, I wanted some advice for a power tool. When I plug in a battery, the drill does not go what would be the problem

Muchas gracias por compartir sus enseñanzas me han servido de mucho para los k estamos empezando este bonito oficio saludos desde Guadalajara Zapopan Jalisco México un abrazo cualquier novedad estoy a sus órdenes Agustín Hinojosa 🫡🫡👍👌💯

What kind of grease and where did you order the parts?

Bună ziua, am schimbat la DTD 152 toată partea electrică adică ,cărbunii- periile adică toată placa care ține periile ,rotorul și magnetul După ce le-am montat a pornit și face scântei la perii în spate, îmi puteți spune de la ce este problema pentru că am pus totul nou Mulțumesc frumos

Why does this work?

Hi! Thanks for what you shate on UA-cam, is really helpful. Do you have any video for disassembly a Makita DHP 485?

Hey my impact driver is acting weird works fine when in forward but then stop and I have to go in reverse a little bit move the reverse to forward and works again but not for long time what are u think it could be

If you own a makita screw gun and it fails just throw it in the rubbish where it belongs and buy.a hilti. You wont regret it

My 273 brushless only works in reverse (hammer, hammer/drill, and drill). What could be the issue/problem?

Qual a medida desce carvão amigo

5:45 I use Scotch Brite to clean the commentator bars.

Hi, I have an issue with my ddf482. Chuck is stuck and iam not able to remove it With Hammer and allen key Do you have any recommendation? Thanks