- 17
- 120 027
İhsan Kömürcüoğlu
Приєднався 16 гру 2012
Krank mili dolgu ve eksantrik mili dolgu ve taşlama
eksantrik mili taşlama (kam mili taşlama)
Hertürlü eksantrik milinin kaynak ve taşlama işleri yapılır.
Переглядів: 1 020
Відео
Kranksan krank dolgu sanayi Aksor 1840 eksantrik mili taşlama
Переглядів 6703 роки тому
Kranksan krank dolgu sanayi Aksor 1840 eksantrik mili taşlama
Krank mili tozaltı dolgu (Submerged arc welding of crankshaft)
Переглядів 1,5 тис.5 років тому
Krank millerinde aşınmış yatak yüzeylerinin onarımı
Looks like submerged arc
عفوا القطاعات المكنيكية
اخواني انا من المغرب واريد ان اشتري هده المعدات لاقوم بتلحيم مثل هذه القطاعات المكنيكية وشكرا .اريد المساعدة
Where is this place located
Where located
abi selamün aleyküm krank milim var kaynaklanıp tamir edilmesi gerekiyor. sizinle nasıl irtibat kurabilirim? çok güzel bir iş yapıyorsun maşallah
abi selamün aleyküm krank milim var kaynaklanıp tamir edilmesi gerekiyor. sizinle nasıl irtibat kurabilirim? çok güzel bir iş yapıyorsun maşallah
Bu saglıklı mıdır,,, yani güvenılırmi
Welding name
Kaynak olsada olmaz
CRANKSHAFT not crank shaft!
I thought it looked too smooth as well.
Greetings from Rio, Brazil. I would like to watch the entire process, from the beginning of filling the shaft with solder to the moment it is ready for delivery to the customer. Is there any secret operation, like "the cat's jump" that those who know and do not show or teach? All the best.
U r number plz
What about the darkness after this mission?
Abi bunun teli ne ? Içi dolumu ? Yoksa başka biseymi hani iki cur tel varya buna hangisinden istifade olunuyor ?
Which type welding
Submerged arc.
awesome sharing sir
Selamunaleykum hocam kırank mili dolgu yapiyormusunuz ve yeriniz nerde
Hello sir i required this SAW machine
Sa ustam benim kasnakta eğri donuyo masraf ne olur 3 kasnak gergi rulmani kayis aldım sorun aynı kayis atlatma yapio
Namaskar sir ATA kothai plise bolban
Thanks sir
+994552265355 Vabulfat@mail.ru
rica ediyorom VHATSAPP bana yaz
That is the true process that should do on crankshafts. 1. welding a layer of iron 2. cutting the journal to standard specification.
Krank kafasınada yapılıyormu bu işlem hocam arka keçenin geldiği yere aşınma olduğu için
is it safe to use again How is the quality of durability
Do you heat the crankshaft after welding pleas help me
What’s the purpose of doing this?
To repair crankshaft that has been damaged. Adding metal to damaged area so it can be later machined to original size.
Welding thus power o not it strenght??for long term
That sub-arc machine is humming. That is as slick as automatic Tig. Bravo to the person who sat that up and the operator!
İyi günler dolgu yapılan krank saglıklı olyormu teşekkür ederim
Radial engine?
Joel Adank yup, looks like a 9 cylinder pratt
Oh dear finally lost it, watched the most boring of all welding processes 3 times and enjoyed it, after a Saturday 8 hour shift welding!!!
What's the sand for?
Submerged arc welding instead of shielding gas like TIG or MIG welding it uses the "sand" to shield the metal during the welding.
It's the welding flux...
I used to have to weld up bearing journals on printing press rolls that got recovered with rubber at a rubber mill. Did it with hard wire starting each pass 180° opposite the previous. When it got hot to where it glowed i would wait between passes and turn 90° when i resumed to try and position starts evenly. Each pass overlaps 50% onto previous. Roll was in foot actuated positioner like a lathe chuck. Especially on smaller journals i had to sit off to the side with journal at arms length and of course i had weld settings vs. Positioner turning rate all dialed in so i did not watch the puddle but rather looked just ahead with the arc flash providing the means to see exactly where to weld. Challenging but taught myself a few things. It's hopeless trying to do a small journal with it directly in front of you. Pull the trigger as you depress the foot pedal to start turning the roll and weld. Stopping the instant it turns a full 360° and you tie each pass into it's starting point. After cooling machine to spec.
Submerged arc welding (SAW) is a common arc welding process. The first SAW patent was taken out in 1935. The process requires a continuously fed consumable solid or tubular (metal cored) electrode.[1] The molten weld and the arc zone are protected from atmospheric contamination by being "submerged" under a blanket of granular fusible flux consisting of lime, silica, manganese oxide, calcium fluoride, and other compounds. When molten, the flux becomes conductive, and provides a current path between the electrode and the work. This thick layer of flux completely covers the molten metal thus preventing spatter and sparks as well as suppressing the intense ultraviolet radiation and fumes that are a part of the shielded metal arc welding (SMAW) process. ~wikipedia