Відео

Use the deadbolt…

Open the noor ah moment

Respect for giving this a shot. I didn't know anything on how to fix my door but you're video did help me out, so thank you.

Thanks to Gary Katz for bringing this trick to the masses.

👍

You’re an idiot for not showing. What’s the point here bud?

Wow unbelievable you actually replied. Thank you it’s just that it’s rare. Thank you I will try

Hi do you know why my fuse blows

Or if you’re carrying groceries in as few trips as possible

trooper

Your fingers are scary Looks like that professor from animal clip those nails brother

What about if it’s sagging or rubbing a little on the bottom? Do the same to the bottom hinge?

We need your help on a Dorma ED700 setup can you reach out?

Same as Walmarts except the controller

Great video. Thank you

Good evening I am very happy to keep you in the installation I would like to have an online course with you is that possible please?

Stanley

Much gratitude!

Hi sir, give one videos how to reset this one

As a field tech with more than 2 decades of experience, and a former employee of Dorma I just want to say that theED700 / ED400 series has always been garbage. The bearing for the intermediate gear tends to fail, the motor's have a habit of shorting to the case. You always want to make sure to check that with a meter before replacing a control box. The ED700s in particular will allow current to flow through the motor to ground causing them to violently jerk open. They get lost if someone props the door open in a power failure. Then they proceed to swing back and forth for hours because the angle drops below zero when the door tries to close. The control boxes are extremely prone to failure during electrical storms, generator tests, power failures. Dorma has a habit of discontinuing all spare parts as soon as they stop selling a particular model. They did it with the old style ED700 with the exposed gears. That wasn't a huge deal because they were simple and the control box was a direct rip off of the Horton 4190. Now that the ED400 / ED700s are gone they no longer offer arms. I can get the controls and operators rebuilt but the arms are getting hard to find even used. Particularly the pull arms which were always prone to breaking,..

Can I put a handicap door opener on a 2000 Plymouth grand Voyager

Much appreciated thank you for the video

Im servicing a pull unit where the spindle shaft was set too low and it rubs the door top when operating. It looks like I have to remove the motor assembly and use a shorter 1/4-20 bolt to pull the shaft further into the motor body by about 1/2 inch. It's either that or I'll have to remount the entire unit slightly higher above the door. There's plenty of exposed shaft so it appears the installer used the wrong length spindle bolt I assume because he wanted to reuse the existing door track holes, which required him to drop the shaft/arm lower. Even so, the pull arm roller is tight against the top of the door roller track. I'll remount the roller track after raising the spindle, making sure it's level with the pull arm mount. These are well made units and fully featured and easy to program, but looks like the installer messed up the install by gambling with clearances. It's been in service 18 months so likely has slightly more play, causing the contact with the door. Hope that all makes sense???? Will report back after tomorrow. :)

This is actually helpful

How to connect motor, eye sensor and main electric..

What a useless stupid video.. This video just makes me dizzy

What if the door closer has no spring tension adjustment?

Why Is the door hard to open when you push it manually.

Great info 👍👍

Yup! That's what it looks like! Now how do you install it????

That’s definitely a Hampton inn

Thats so cool!

Hello sir mujhe automatic door fitting work learn karna hai

Why??

That one guy dipped

wtf.

Why is this content on youtube

That's easy, stanley duraglide 3000, the best slider in the world, it's so good the basic design of it has not changed for decades (I'm looking at you besam powerglide 2000/3000 , amd, unislide, sl500... can you just stick with one decent design?)

Stanley duraglide

Fire alarm is not there

wooow this is great! I've always wanted to know what the backcheck was for. Thanks a bunch for the explanation.

Great installation of the door the store looks great with the door Next time show us how to put the door together

It sounds nice, but I love the whirring noise of the PowerSwing (the model that came after the Electra150) even better.

thanks very helpful video

7.7 24..good video. Have forty devices readjust. Installed twenty years ago. Ol style2227 pre 1998 Model.

How do you scenes it to gether

This does not cover repair of flush bolts or fixing flush bolts, just how to use flush bolts. Nice video but not what is stated.

Thank you for this! Do you have any ideas on why the bolt might fall? I'll lock the door and the bolt will go into place, but then, if you jiggle the door (or maybe not even with that!) the bolt will fall, unlocking the door! Not great for my business! Any advice greatly appreciated. Thank you!

BMStores. Zip tie Fire Doors together Why Modify fire doors? ua-cam.com/users/shortsn5MbA0itpCQ?feature=share