Відео

nice one, thanks man. I have a stuck milwaukee but maybe they all licensed the same patent.

Do you think this reel would be a good investment for saltwater fishing?

Put some music to it

Still sick build!

Suggest check the washing machine shocks, if it is a few years old. And maybe mount PC through rubber damping of some sort?

not good at all mate 😅

Do not do this. It is a safety hazard because American outlets use 120 volts, while Australian outlets use almost double that voltage.

Can you put it back together?

Thanks so much for making this video Gym! I had a small piece of PLA break off nice and snug in the heat break where neither the extrusion gears nor the heat could reach. Practically impossible to get out without following these *exact* instructions. For anyone in the US with only Imperial bits, a 5/64in bit is 1.98mm and worked perfectly for me without damaging (much less "completely destroying") the heat break.

If the main gear and oscillation gears are brass or stainless then it’ll last forever. Otherwise with salt intrusion, all those zinc parts will pulverized.

Why don’t u f off and do something u wanna do

Holy wow! 79$? What currency? This reel is 45$ Canadian here Canada. That's crazy it is sold that expensive

Where were these shows?

I work for Boeing, weve been doing this for years.

Damn Bro , Onwards and Upwards I know all about starting again at Fiddy , it Sux 😑 threw a Sub your way , Take it easy 🍻

its last longer then couple of days lol

Don't be cheap and go to the hardware store and get the right size.

LOL, I hope he does not use that method on lug nuts. 🤣

For a few days? I have duck tape on my truck that was applied when Obama was president.

Ah that sux. A tiny part breaks and a replacement piece is the cost of a new tool. If you know anyone with a small lathe they could whip up one of those pins _tout de suite_ for a few dollaree doos or a slab.

1:21 Holeee 💩, actual fuses. 😲 Can you still buy fuse wire now days? Don't see the standard piece of cardboard with the different wires wrapped around it sitting on the bottom of the meter / fuse box. Someone should be jailed for that egregious crime of fuse wire negligence. 🤭 *$200,000* _Tell 'em they're dreaming._ You gotta be shitting me even if it has got a nbn Fibre Modem. Can buy a much newer and nicer place of a similar size in outer Melbourne for twice that or a 2BR Unit for 360K a lot closer in. Why are country / rural prices so far king high? I was going to ask what your injury was (I recognised the breathing that I used to make on my dashcam) but saw the walking stick in the video. Hope you recover from whatever it is. Constant pain id so physically and mentally debilitating. Is Mallanganee out of the flood zone? Saw a much, *much, MUCH* better place there for $248k. I is bored stupid so looked up where these places were. Can't believe the prices they want for run down shitholes but I guess I'm just old and dreaming of the prices 20 years ago. 80K for that block. 😱 I paid less for mine that is 50km from the Melbourne GPO only 22 years ago and it's not on a flood plain. In fact when the oceans rise we will have a beachfront property (miles from the sea at present). 😁 *Thanks* for the video. 👍👍

If you use strips of aluminium beer cans you can get a spark plug to engage a stripped cylinder head. Still hanging in.

I don't see any stripes on the striPPed bolt. Stripped, not striped.

Are you aware of what happens when you dissolve resin in alcohol and have it all over your hands? It goes straight through your skin into your body. Keep doing that and you're going to have a very bad time. I'm not being alarmist, what you're doing is very bad for you. Not only that, you're washing it straight out into the water supply which is also incredibly bad. And on top of it, you're spraying it all over your dishes and surfaces in your kitchen were you presumably prepare food.

was expecting stripes, am disappoint

This is the most Australian sounding person I’ve ever heard in my life. But good tip! 👍

Hi mate, does this work with PLA or only for ABS filament prints? Thanks for the video

I got a set with the fan and all that and so far the brake high section works, but I also put it in 4 way flash to make sure it was doing what it is supposed to be. The fans are loud enough I can hear them when I hit the brakes too. But I don't doubt what you say as a lot of the dirt cheap leds don't last very long or work right. I got a wierd set of 9005 and 9006 flat leaf looking headlight leds and so far they throw a clean super white beam spread and other than the color they are very similar to what the halogen bulbs did. They also were able to be rotated to get the light source properly aligned to work in the housing. The first set I tried claimed 6k but were super blue and the light didn't throw out very far either. Couldn't see very well and they died in 6 months. The new ones are so much better all around but we'll see how long they last.

The lews spinning reel should be a guide a good reel for the money and turns freely and it’s a 6 bearing reel just like Penn

The diawa silver series only had 3 when it came out most early Penns only had 2 along with Mitchell Garcia and others in the 70 s and 80 s great reels just once a year service them I still have 406 salt that rolls the handle over if I flip my wrist Bearings greased washers and drags greased will do most anything

Did yours come with spare washers. Do you know where they go?

What a rubbish reel

So the 3 x FDM's are your 1st attempt and that red missile launcher on the right uses 40yr old legit GMH blank plate... 😂

You can buy a whole kit of 447 various plastic car clips for $30 from Sydney Tools (Daytona brand), has the ones for the door cards & everything; have been using it on my Pops 1996 Astra that im fixing. Rare Spares used to stock them too, dunno if they still do

This is the exact sort of thing 3D printers were made for. Awesome work, well done and so quick too. Years ago I was worried I would never be able to get parts for an old Datsun, now they can be 3D printed.

That was painful to watch just fibreglass patch where the stupid plastic Holden clips are then screw into the patch everyone with a Holden ditches those stupid things not 3d print new ones Poindexter.

Its to old car👍

Why do you remove the nozzle?

i was having this very problem on amazon looking for a new PENN real. i finally went to the manufactures website.

They havn't tried copying anything mate 😆, Only the logo has been slapped onto some chinesium reel. There has been some fake Daiwa reels showing up on places like aliexpress too. Just gotta be careful and also have common sense.

Wow nice car 👍😲

Hahahahaha…females think they’re productive- how cute.

wait....who has dyslexia... 1min 23seconds you said let's Google this model number and instead of Googling KB2000 you Googled BK20000 lol

Do you remember which wiring kit from SCA you used?

Nice video mate! Cheers

3 generous dobs of silicone and some duct tape until it dries. Thats how I do it but hey I'm a bit of a hack sometime but it is effective

This video is definitely not for people that want to watch a gas tank patch.

Yes, but can you fix the hole in my heart....😁♥

What is that😲

This is exactly the video I was looking for. The second these get dipped in the water they squeak pretty loud. Thanks for the good vid.