Відео

I would go to offshore electronics and look at what TFL offers. Offshore electronics also has a few of their own boats they sell as well.

I originally reached out to him on facebook, he's the only one the pops up when i search for him from Oregon

that run was actually with some balanced and sharpened miss gieco proboat props, the temps don't get too bad at all with those. When i run the Super Zondas from Dasboata I can only run 1 or 2 passes and everything is hot

Its a Futaba 3PV. No telemetry. It's been a good radio and has awesome range. My only complaint is that the receivers are pricey and pretty sensitive to water.

@bryanhulsey406 I just returned the radiomaster mt12 bc of the learning curve is to much for what I need and no gps. I then purchased the Wfly x9s with voice telemetry and a built-in gps that says outlook the speed and voltage. The range is advertised as 600m I had the elrs mt12 and the receivers are very sensitive to water as well even after using CA glue on all the seams it still got destroyed after 2 uses. I got super frustrated with the radiomaster. So I'm excited about this new radio.

@@RDM3DLAB I'll have to give them a look. Hope you have good luck with it!

no i did not have this issue, I would contact Ose. Sounds like there may be an issue with the teflon liner.

@@BoatsBrosRC ok. Mamy thanks !

The stock shafts are 2 pieces. Buy the 1 piece shafts from OSE. 80 bucks. Contact Steve at OSE, he owns it and he'll help you with anything you need. I flipped my zonda today at about 70 I'd guess. It was floating with the front tips up and was still running while completely submerged with the props still spinning as I retrieved it.

@@jcallesano thanks a lot , i already got the new flexshafts from offshore , does your zonda get some water inside after running it for 6-8 mins ? Mine does, its not much but a boat like this should not get any water inside the hull. I am greasing very well the shafts with marine grease , and the boat is in perfect condition .

​@@eduardonessim4499 not that I ever notice with water. Maybe the stinger socket connection? Check all hoses to make sure they're tight in the boat.

my brother built it himself, it is running a 6s battery on each motor.

@@BoatsBrosRC congrats to your brother !!! Awesome job .

my bulgarian has a square that has no carbon in it that lets the gps signal through. works pretty well

@@BoatsBrosRC You must be having a lot of fun! That Bulgaren and Zonda are both great boats.

some of my boats have surface ESCs converted to watercooled.

my fastest recorded pass has been with ZEEE batteries. (117mph) I'm pretty sure I went faster the other day but unfortunately, I flipped and ripped the GPS off the top.

@@BoatsBrosRC ZEEE batteries get a bad wrap for inaccurate specs but you prove what i mention about performance is the final measure . The Gens Ace basher batteries perform real good too for a pair of 4s and the ESC like them too . Sorry to bother but did you get that connector that joins two 3s lipos together to send 6s to both ESC , connector works but creates heat .

@@waynesbutler7834 I got one of those connectors with both of my zondas and my miss gieco but i've never used them.

The 6s CNHL 6.0 G+plus 70c batteries fit in my zonda stock without trimming any carbon fiber. I put the 44 mm speed props on for the first time today and flipped it and had to kayak out to get it. Lol. Was floating with the tips up, hatch off and props still spinning by themselves. When my radio is off, they spin by themselves for some reason. I also have the harness that you run 2 3s batteries to make 6s, but the 2 6s batteries is by far superior

@@jcallesano Thanks so much for this , i am always looking for batteries that will fit without modding and i like CNHL batteries, spent alot of money on this experiment, thankfully they were from Amazon so returns real easy. I will give these batteries a shot. I put the 44mm high rake props from OSE , balanced , sharpened and polished on my boat and got 102 mph without flipping, batteries all the way forward running real wet at slow speeds. Stingers approx 1/8 of an inch above the level line across the bottom of the sponsons.

that would be my kitten 😄 you can see him a bit at the 1 minute mark.

as long as your ESCs can handle the amps. I wouldn't run them very long. just a couple speed passes.

Thank you,will keep it in mind. Running 2 x XLX2 ESC’s. Just installed.

@@michaellidis1148 those ESCs are pretty tough, should have no problem with the 48mm props. could actually go bigger if you wanted to.

I wish I built RTR boats for a living. Sorry if the video was misleading.

it's crazy what can happen in a crash on the water, I've spit 2 hulls myself.

118mph pass was from the Bulgarian. The Animal ran 102MPH. We do plan on making more videos of it. The one we have is the ARTR animal V1.

Kevin, we do most of our boating at Lucky Clover camp resort in Steelville, Mo and the owners love it! They let us have a big gathering there last summer for RC boats.

we're normally there on Sunday afternoons, the majority of the campers have already left for the evening. Them most of the others that are still there seem to enjoy watching.

Indeed!

I have filled the tips on the fiberglass zonda but not the rest of them. The Bulgarians are a lot thicker and stronger than any RTR boat you will ever buy. The carbon zonda I feel like will eventually come apart but for now it has been holding up pretty well. For prop rotation the zondas, mti, and drambui turn outward. The animal, bulgarians, and twin bj turn inward.

@@BoatsBrosRC THANKS

Thank you!

Boats around 114cm are definitely more likely to take flight than my 145cm boat. But they can handle the flips a lot better, flipping a 145cm boat there's a good chance something will break.

got to tune them to keep em planted.

I had a 1/5 scale 2 stroke Hydro. one of the coolest looking boats I've had in my opinion. I just don't like dealing with the gas, getting it started and warmed up, and lugging that big sucker down to the water just to run maybe 35-40mph. I'll watch the gas guys all day long, cool boats but I prefer FE.

it is a bulgarian hull custom painted

Phoenixx, they don't fully sink. Keep the whole front of the boat stuffed with pool noodles and the front tips of the boat will still stay above water even if you do split the hull and it fills with water.

It all started from a wrecked Geico 36. Swapped motors and ESC's over the BJ. Bought motor mounts from OSE and mounted motor them the same disrance back as the Miss Geico. That way i could always just use Miss Geico flex shafts for replacements. Also uses Miss Geico drives out back. Had to do a little griding on them to raise them up higher but not a big deal.

ua-cam.com/video/gxdSy3O89ag/v-deo.htmlsi=p3wOE_7KfFMRq1u5

there is another video on the channel with more pics and videos of the Twin BJ