- 8
- 56 059
aviator978
Приєднався 30 жов 2011
Відео
Whirlpool Duet Dryer - Squeaking Fix
Переглядів 34 тис.Рік тому
My Whirlpool dryer was making an awful squeaking noise whenever it was running. In this video I show how to find the cause of the noise and also how to fix it.
Using a Slide Hammer to pull axles on a 57 Chevy
Переглядів 1072 роки тому
Here's a quick video showing how a slide hammer can make quick work of pulling rear axles.
2005-2010 Grand Cherokee - Spare Tire Winch Substitution
Переглядів 7 тис.2 роки тому
In this video I show and discuss my solution to the low reliability of the stock spare tire winch in the 2005-10 Grand Cherokees.
2008 Grand Cherokee Blend Door Repair
Переглядів 12 тис.2 роки тому
This is a video based on and complimenting the repair kit sold through www.blenddoorrepair.com.
Whiskas
Thank you! My model is older and looked different in the back so I went through the front via another video for that part. But your video was crucial because it gave me the view of the belt and idler I needed to be able to take the belt off, replace the idler and put the belt back on. The view is limited from the front. 😅
I need to replace the wiring harness
This video was awesome! Clear, concise and best of all, saved me over $200! Thanks for making and sharing this! 👍👍
no grease on the shaft?
Correct. clean the shaft off and put the new pulley on. No grease.
Sèche linge au gaz
Great video. I really appreciate how thorough you were. You skipped nothing. Thank you fir sharing. I am not very handy, but this video gives me some confidence I can tackle this.
This is the best! Worked like a charm.
Great Video: What was the parts number on your video. I have the same dryer and I am having a hard time finding the parts on your video. I have to replace the belt too, could you help me with that?
Take a look at www.partselect.com. You'll have to type in your model number. I like this site the best so far because it has assembly schematics that allow you to see where the part goes and make sure you're buying the correct one.
What do I do if the entire inside broke though?
What do you mean? Did the shaft for the blend door break? Are you able to open and close the blend door manually? Or is the shaft broken so bad that the blend door is stuck down (by gravity)?
You removed the belt and spun the drum, please explain how you were supposed to indicate the motor bearings or what the purpose was without the belt? Just curious
When I spun it by hand the first time, the only thing I was checking was the drum wheels/bearings. If it still squeaked when the belt was disconnected, we’d know it was the drum and not the tensioner pulley or the motor bearings. But, you’re right. I didn’t eliminate the possibility of the issue being the motor bearings. I basically moved forward on faith that it was the tensioner pulley and not the motor bearings.
Have a Jeep Grand Cherokee 2008 Hemi. Passenger side heat not working. This will cure it?
Probably. Until you get it apart, it's hard to say what's causing the problem. It could be the blend motor is broken. That's an easier fix. Can you hear the blend motor operating when you adjust the passenger temperature? If so, then the gear is probably broken, just like mine.
Huge thanks!!! Fixed my squeaky dryer. Any reason after this fix tho the heat would stop??? That’s my current problem
Not sure. I haven’t had that problem yet. Sorry my friend.
Is yours also a gas dryer? I don't mean to insult you, but if you disconnected the gas to do this project, did you turn it back on?
It’s Christmas Day 2023 & I needed this. Thank you! You’re an excellent teacher
Thank you
Appreciate this video. I was able to go straight to my problem. Thank you!
Hi Mike u think my 07 jgc laredo blend door knob will be similar to yours on glove comp side?
If you have the control knobs like mine, I would expect the same blend door motors. If you're having trouble with the passenger side temperature, that motor should be on the glove compartment side.
@@aviator978cool I’ll be checking on that later today I’ll give u an update ty for the reply sir 👍🏽
Would you happen to have the confirmation email that has the part number of the whirlpool replacement part?
It's silly, but I can't find the order confirmation email. I've searched for whirlpool, pulley, wheel. Nothing comes up. If I remember correctly, when I bought the part, I did a google search on the whirlpool model number. I found somebody that had a schematic with part numbers.
My 05 gjc doesnt leak any water into the cabin, but would this method help my AC blow colder? It is ok at the moment nut not great.
It might help. But, I would guess the blend door is not your issue. When mine was broken, it was stuck on full cold. Gravity pulls the door to the extreme cold position. If yours is broke like mine was, then you should have no problems with cooling. If however, there's something wrong with the calibration of the blend door motor, then it might not be moving the door all the way to the closed position. You may need to do some googling on blend door calibration and see if that helps. But, my guess is you're low on freon... which means it's leaking somewhere.
@@aviator978 it's not Freon, it's r134a refridgerent
@@wkjeeping9053 r134a is a type of freon.
Thank you for this video! My dryer is back to working as normal.
actual life hack that is useful
Now that’s genius
smart hack✍️✍️
Looks like I'm going shopping for a pool noodle! Great trick. The sconce in the video is the same as mine. Always hurts my hands but no more, thank you!
Thank you my dryer is fixed!!
thanks so much followed your steps exactly and it was very easy and straightforward.
_18 years of great use with mine until this exact problem. Thank GOD for you._
Do you know if the 2011-2019 jgc can mount the tire to the underside like this one
No, I don't know.
I have a problem with the dryer that looks like the one on the video that you show. The lights come on, dial in the instruments are set but when I hold down to press start. It does not start to turn on. The only difference is that the sensing light comes on. Any help
Sorry, I haven't had to tear into the panel, so I can't offer any help there.
You should ck the dryer board it's on the upper either left or right side and it's prob fried, notorious for this problem and if u ck on internet it will tell you how to fix it
What about the flapper that controls the air flow. My jeep 08 liberty doesn't blow air out the front vents. I hit a bump one day and since, no air flow to the vents. The floor and defrost work fine. I have tried manually moving the part you are working on that controls the flapper, it still won't open the front air vents. (Actuators are good and function) I think the flapper might be stuck possibly, but for the life of me I can't figure out how to get to it to check it. Any help would be appreciated.
This video is specifically for the flapper that regulates temperature. There's another actuator and flapper that controls which vent the air goes through. I'm not sure where to find it on the liberty though. Sorry.
Great video, simple, fast, to the point...
One of the unknow quantities here, is if your actuator is not the cause of the problem, this may not be your solution. It's good to have a scanner of some sort, you may find some hidden codes that don't trigger a mil light, like the blend door actuator circuit open, or something similar. You could have a bad ground, short to ground somewhere, broken wire, etc. I highly recommend checking into it before going through all the effort of changing the part.
Maybe so. I wasn't aware that blend door issues would throw a code. Either way, it's not too difficult to remove the glove box and listen for or feel if the actuator is operating.
Would it throw a code????
Awesome video great help. What was the part number for the pulley?
Excellent demonstration, thank you so much
Looks amazing!!
Best video ever
Very helpful - thanks.
Awesome thanks for sharing!!!
I think the supplied drill bit is a hair too small. It was so tight screwing in, it broke the new repair actuator. I even ran the bit through the hole a few times to make sure the hole was clean.
is this just for hot air on the passenger side or both heat and ac?
Both. If for some reason your blend door won’t move, it’ll either be stuck on cold or stuck on hot.
@@aviator978someone else have this video but his blender actuator knob just slides right off and could be easily replaced w a new knob no drill bits needed 🤔 I ordered this part today from Amazon $9 but I’m checking my 07 jgc laredo tom first thing in the morning if exactly what kind I have or which is broken I hope mine is the easy knob that slides right off 🤞🏽im praying 🙏🏽🫣 I have a single heat zone n it was clicking forever but now clicking is gone and heat adjustments all went away as well
Maybe I missed it but where did you get the replacement part from?
Www.blenddoorrepair.com
Your video was extremely on point! The control arm on the passenger side of my Grand Cherokee was broken,(already had the parts). I had a new one installed/reset in 15 minutes. Your video saved me an expensive bill at the dealership!
Same thing happened to my 05 when i tried drilling the white piece it went inside 😢 i really need it to be on hot
Same happening to me.Did you find a way to fix it ?
@@fuyo1563 unfortunately no, i drilled hole on the side of the airbox and tried to life the divider manual with a screwdriver but that didn't work, let me know if you figure it out i live in Alasks i really don't need it on cold not even in the summer
that belair tho