Відео

Thanks for the good instructions. This is the best video I’ve seen so far on how to do this. Thanks so much.

I’m going to start calling my 65 corvette that runs hot a whore too ! 😂😂

I forgot ALL about the steam holes needing drilled in the residing heads; a mandated need👍!

Love the 400! That hooker is really talkin!! I see you got some Vortex heads on her- So if you don't have one already in it, try a thermostat with a by-pass hole or a weep hole. If you have both of your fans hooked to the same temperature switch they should be divorced to where one comes on first say at 195 then the second at maybe 205 or 210; but you will need a 195 t-stat. And also if you are running antifreeze or a mixture of it, it does not transfer heat as well as plain water. Since city water is generally loaded with calcium chloride, the chloride portion of it is pretty corrosive; especially in a system containing both ferrous and non-ferrous metals. To avoid that, always just run distilled water in your cooling systems. Forgive me if I'm wrong but from my Keyboard Commando post, it looks like you are in Cali., somewhere. My point being that if your latitude does not see too very much below 32° F, I wouldn't even consider running anti; especially not with a 4 hundred sbc and let alone in an .030 over mill. Please keep us filled in. Btw- NEW subscriber here!!

U need to put the original fan back on that spins with the motor and a shroud and u will be fine.

Can you show the front support.

My impala sat high in the front (still does) but the bumper, brackets and hood dropped it half an inch

Brother, where did you get the fabric from? I have a 91 silverado with blue inside

Paint stopper upper 😂

Why do people not spring for the one piece gasket? 😂 You did get a one piece those corks suck

Take the pump off the block and install it on a table propped up by some 2x4s and use a steel gas pipe with a cut out channel on it, works much better than a wrench. Looks good though. I had a panic attack watching you put that hammer on the crank and rods 😅

Hey bro i have a question? What is the correct way to seat the reverse lights in the rear bumper mine stay lose?

What tire size pops?

Best description yet on how to help you choose the right pump!

Hit that mute button. You don’t need stupid music man

💯💯👍✌

Did you spray paint the dash bezel?

@ 5:26 & 9:45 calls it a name. That's how I mechanic.. lol

Appreciate that information bro great looking obs Chevy boys for life

What size motor is that

Your videos have helped me a lot with my project car. So just wanted to say thank you for the help.

Thanks , very good video ,had same problems

Did you install the energy suspension radiator bushings?

If it’s the short water pump what’s the rotation on the water pump or the way the belt should spin the water pump to? Im having issues with overheating , possibly misrouted belt

Mounting flange on the headers is probably warped or twisted.

Así tengo un impala 66 convertible acá en México, aquí no hay por un ejemplo los bujes y gomas q le puso, quiero achaparrarlo, omo lo hizo UD mi parabrisas está roto y aquí no hay se batalla mucho bueno lo principal es que es una chulada gracias por sus videos veremos el color q le pone

Nice ride I got one just like it thanks for the video love the impala

Thanks for the update video on the impala

I see the dipstick tube is on the drivers side, while the 350cu in 4-bolt 1975 era is passengers side. Like you, trying to use the OE cast iron exhaust manifolds doesn't have room for right side oil tube. It right in the way. Didn't want to do heads as all matching the 86 Monte SS look. Still scratching my head! Thanks for the video.

these videos are helping my impala install

Do you recommend putting oil in the cylinders before starting a engine sfter replacing head?

Looks nice

Calling parts on your car a whore is the most relatable part of this video lol

Does pushing the fluid out of the clear hose empty the pan basically?

Great vid

Great video, thanks 🙏 for not editing your mistakes, I seen a lot of ignition cylinder replacement videos and all them dude broke a screw and edited that part out. Only seen 1 guy say there’s 1 hidden screw the rest just said “grip it and rip it!”😂.

Of course it will run take care of the beauty bro

My first car i owned was a 1982 Buick skylark.600 bucks This was in 1994. They look similar. When you turned the wheel all the way to one side or the other it would stall. 😂 my second car was a 1984 dodge ommi. When you shut the car off it would continue to try to run. The girls loved it. 😐 Love old cars.

great video thanks

Q pasa Whatever happened to the 66 impala I appreciate all your videos and your videos of the 66 helped me out with my car Thanks

My 2005 Honda Metropolitan that I bought new in 2004 from Honda Dealer in NY currently has 65,787 miles

You did a better job painting your engine then I did!

looks great man.

I had the same problem, bought the install tool..😮 screen was installed in a minute!

Hey man what Edelbrock intake is that what model ? Does it clear your hood ?

Don’t tell me it’s a 1978 Ford Fairmont 😁

Great video thanks for sharing

Will you be making a man cave / garage to work on your cars.

This is great. Once the rates come down you can refi and lower your payment quite a bit!

Pick up coil in the distributor needs to be replaced. What happened to the impala? I have 2 1966 project impalas. Fuel pulse on injection is controlled by the spark from the distributor. I had the same problem