Відео

Thank you

Thank you for identifying the value. yes, it is 3/4. the final value of Y22 is 51/52. please make a note of it.

Thank you, Mr. Lokesh,

No please analyse carefully Y12 is 1/4

Good question. If In the place of 12F capacitor, an inductor was present, then the current through it would have reached to a value of 2 amperes. Then, the rest of the solution ( i.e., the final capacitor voltafe across 6F)would have been dependent on this inductor current.

Thank you

Thank you Fatima

ya ECE branch related subjects if you prepare well, you can appear for engineering services

@engineeringbasicsforcoming2179 OK thanks sir And from which branch should I give GATE Means Which Branch has more scope to Get Job Either CS or EC

Choose ECE

Please choose ECE engineering

Thank you sir

hello shadinh armature resistance is given the problem to be 0.2 ohms. you try to take any other value and calculate the load current

thank you

exam hai kya bhai

Thank you for response

Thank you

sure send me ur mail id so that i can send you this information😇

Thank you, Nirmal, for your response. Please share this information with your friends

Well, Thank you

Thank you Sir

sure send me ur mail id

Thank you sir

First you draw OCC line, then draw a tangent line on that OCC graph. then randomly draw a parallel line and perpendicular line on the tangent line as PQR shown. its simple please check the video once again

@engineeringbasicsforcoming2179 thank you very much sir. Can you please make simple videos on "transient analysis" and "Laplace transform" both the topics?

​@@sayanghosh8307yes sir I also need this topics please make videos on this chapters

sure sayan i will try to do that as early as possible

@@engineeringbasicsforcoming2179 please sir make it soon my exam is from December 2nd

Thank you Sir

Thank you for your valuable feedback. I request you to get clarity in your statement about deciding switching conditions. I have mentioned correct information in my class 4 vedio.

Thank you

Thank you

Thank you lokesh

Thank you rollno235

Thank you for your interest. I will try to do that as early as possible

Wow

Thnak you

remember here, I2dash= -2I2, check the notation after 15 mins duaration

Thank you Sir

Hey Thank you

Thank you

Thank you

Your are welcome...... Please support this video... to many students who are desperate to know what is exactly engineering?

Well, Control Systems is a special mathematical tool used in Electrical and Electronics engineering courses in order to under stand and react to physical systems.

The basics of this subject (control systems) one can learn in undergraduate program of bachelors degree under stream of electrical or electronics engineering. Later, one can go for Masters in engineering in control systems specialization. Control systems engineering is widely used in the fields of medical, mechanical, electrical, electronics, agricultural, aeronautical, radar, telecom and communications systems.

Exactly Sir., Thank you for your response

Thanks for your response. you are write, i(0+) = 6A. Thank you once again, because of your valuable comments, I can work on my mistakes.

admittance(Y) is a reciprocal of impedance(Z). that means if V/I = Z, then I/V = Y. Here( I11/V11)= Y11, that is why Y11=(3/2)s simens(s)

hello before t<0 inductor was not energized so no current flows through it. at t=0, current through inductor does not change instantaneously. That is why we should not consider at t=0 condition. after switch is closed that is at t=o, inductor get connected to source current 6A. after t>0 inductor gets charged. After some time i(t) is 1.49(1-e^(-2.22t)). that means inductor is getting charged to its maximum value. at t= infinity (steady state value will be) 1.497 ( =1.5A) and inductor becomes short circuited.

yes very soon i will take that topic

thank you

Thank you for your response

thank you

Thank you

welcome

from port 2, I2dash is equal to I2 minus 3I2, You please check and let me know whether you understood or not