- 68
- 340 027
beardedgarage
United States
Приєднався 26 гру 2020
I love working in the garage and I’ve been a professional moron for most of my life. Join us in the garage, where, If it runs on gas, we’ll probably work on it. We have a few late-model, air-cooled Porsches and we do all our own work.
2021 Kubota KX033-4 - final drive oil change
Here we change the oil in the final drive of our mini. Factory recommendation is at 50hrs and then every 500hrs thereafter, but we do it much more often; it’s quick & cheap to do and it prevents the very expensive drives from going bad.
You’ll need the Kubota gear oil, an 8mm Allen wrench and an oil pan for this job
You’ll need the Kubota gear oil, an 8mm Allen wrench and an oil pan for this job
Переглядів: 73
Відео
2021 Kubota Kx033-4 engine oil change
Переглядів 131Місяць тому
At 200hrs, I’m performing an oil change on my mini excavator. You’ll need a 22mm socket for the drain plug, 5.3 liters of Kubota 10w30 and a Kubota oil filter HH1C0-32430
2014 Porsche 911 Carrera S - Fabspeed valvetronic install, Advanced Flow Engineering intake install
Переглядів 100Місяць тому
In this video we install a Fabspeed Valvetronic exhaust system AND an Advanced Flow Engineering (AFE) intake on a 2014 Porsche Porsche 911 Carrera S
Porsche 993 - Steering rack removal, rebuild, install - part 3
Переглядів 127Місяць тому
After removal and rebuild, in this video we put the steering rack back in the car
Porsche 993 - Steering rack removal, rebuild, install - part 2
Переглядів 212Місяць тому
Rebuild video of the steering rack, going into detail for a left hand drive steering rack. For this job I required - KLA industries steering rack kit for Porsche 993 - Bentley manual
Porsche 993 - Steering rack removal, rebuild, install - part 1
Переглядів 2972 місяці тому
1997 Porsche 993 with a leaking steering rack. I’m removing it and rebuilding it on the bench and detailing the effort that goes into it.
2021 Kia Selos S AWD - Brake job
Переглядів 2922 місяці тому
We’ve got a 2021 Kia Selos making noise while braking. We take a look, diagnose, and replace both front and rear pads and rotors.
Kubota RTV 900 - oil change
Переглядів 1,1 тис.4 місяці тому
Time to change the oil on the 2005 Kubota RTV 900 4x4 diesel side by side. It’s a quick video and you’ll need ~3.5q of 10w30 oil, a Kubota HH150-32430 oil filter and a 14mm wrench. Good luck!
2010 Toyota Camry SE - radiator replacement
Переглядів 7595 місяців тому
We found a radiator leak and it’s time for a replacement. In this episode, we drain the old radiator, remove it, replace it and fill’er back up.
2010 VW abs sensor & wheel bearing
Переглядів 1278 місяців тому
Follow along as my son and I debug his ABS light and after some tinkering find out that it’s all caused by a bad wheel bearing.
2008 Hyundai sonata - engine misfire diagnosis
Переглядів 1,1 тис.9 місяців тому
2008 Hyundai Sonata that we scanned and saw an engine code of P0301 - misfire in cylinder 1. We did a bit of debugging and diagnosis, pulled the intake, replaced spark plugs, tested the coil packs and fixed the misfire Spark plugs: www.napaonline.com/en/p/AC_41800 Ignition coil: www.napaonline.com/en/p/ECHIC626 Spark plug tool: GEARWRENCH 3/8" Drive 6 Pt. 5/8" x 6" Magnetic Swivel Spark Plug So...
Ferris IS600Z Oil change
Переглядів 4,1 тис.11 місяців тому
Changing the oil on a Ferris IS600Z lawnmower with a 25hp Briggs motor. Pretty much the same for the larger Briggs and the Kawasaki Oil filter - Briggs C1K2 Oil - SAE-30
Adding an LED light bar to a Ferris IS600Z
Переглядів 546Рік тому
In this video we added a light bar to the Ferris mower. The factory Ferris lights are halogen, kept getting hot and burning out. Light bar - Nilight - a.co/d/0XCc0jX Solder shrink connectors - a.co/d/cNXNZpM
2010 VW Golf radiator cooling fan replacement
Переглядів 9 тис.Рік тому
This 2010 VW golf was overheating when parked and it turns out the radiator cooling fan was shot, so we had to replace it Radiator fan - ANTUKO 621490 620-805 Engine Radiator Condenser Cooling Fan Assembly Replacement for 2005-2013 Jetta 2010-2013 Golf 2012-2013 Passat 1K0959455ET 1K0959455FR 1C0959455C 6X0959455 12V a.co/d/1WALdMo
2015 Toyota Tundra bumper replacement
Переглядів 4,1 тис.Рік тому
2015 Toyota Tundra bumper replacement
Porsche 993 - Replacing door handle gasket
Переглядів 4,4 тис.2 роки тому
Porsche 993 - Replacing door handle gasket
Porsche 993 - Replacing moonroof seal
Переглядів 4,2 тис.2 роки тому
Porsche 993 - Replacing moonroof seal
Porsche 993 - Painting calipers, replacing rear brake pads, replacing wheel stud
Переглядів 2,5 тис.2 роки тому
Porsche 993 - Painting calipers, replacing rear brake pads, replacing wheel stud
Fisher V-plow - How to mount quickly
Переглядів 5 тис.2 роки тому
Fisher V-plow - How to mount quickly
Porsche 993 - Restoring the fog lights
Переглядів 4 тис.2 роки тому
Porsche 993 - Restoring the fog lights
Porsche 993 - Installing & reconnecting the motor
Переглядів 2,6 тис.2 роки тому
Porsche 993 - Installing & reconnecting the motor
Kubota KX033-4 popping stumps and clearing a yard
Переглядів 10 тис.2 роки тому
Kubota KX033-4 popping stumps and clearing a yard
Porsche 993 - Engine prep & installation
Переглядів 3,6 тис.2 роки тому
Porsche 993 - Engine prep & installation
Porsche 993 - Prepping engine bay for motor (fuel filter & engine sound pad
Переглядів 1,3 тис.2 роки тому
Porsche 993 - Prepping engine bay for motor (fuel filter & engine sound pad
Porsche 993 - Installing release bearing, pressure plate and transmission
Переглядів 4 тис.2 роки тому
Porsche 993 - Installing release bearing, pressure plate and transmission
Porsche 993 - Flywheel, rear main seal, pilot bearing install
Переглядів 1,5 тис.2 роки тому
Porsche 993 - Flywheel, rear main seal, pilot bearing install
Oil change on John Deere ztrak z525e
Переглядів 2,7 тис.2 роки тому
Oil change on John Deere ztrak z525e
Do you need to add transmission fluid? Where do you do that on a Camry. Mine is a 2007. Great video.
Labadie Tunnel
How you pop the hood up
Thanks that helped. Looks so much easier with engine out. I am fighting with right side engine tin bolts 🤬. How’s the results? 7ftlb working ?
@@asteele911 she’s running like a champ. New plugs and wires made a big difference. You might find loosening the engine bolts and lowering the engine an inch or two won’t stretch any wires but give you the room you need
ShOcK & AWE I had no idea (mark time) that the Fork/T.O. shaft had the ability to "shaft the installer?".... So it actually acts as a safety pin to prevent engine-fallout (at any speed)? I haven't been this impressed since I stepped out of the shower dripping wet - sorry for that visual. I'm a rear (don't read ahead!) engine, air-cooled fan for >50+ years and this detail I missed. I saw it coming but I didn't want to believe it (last thing my GF said before going blind ). I'm going to be installing all of that soon and I just want to say THANK YOU from the bottom of my knuckles. And thank the Gods I have a (cheap) bore-scope-cam, too. All very COoL. I'll be dreaming about this tonight. So if you hear faint screaming.. well, yeah. This video was truly sub-worth. The check is in the mail! Cheers from So.Ca.USA 3rd House on the Left (please call before stopping by)
@@ovalwingnut best comment ever!
@@beardedgarage You are a gentleman and a scholar... ⓉⒽⒶⓃⓀ ⓎⓄⓊ
Nice and easy, great to see👍🏼
@@randyanthony2230 I’m glad someone is watching
Where do you buy the cover for the floor?
@@PedroAlvarez-cl9rr weathertech.com
Just what I was looking for. Thanks for the great DIY video!
@@alpha1dcd I’m glad it helped!
I appreciate you posting this so I knew what I was about to get into. My 993 steering rack just dumped fluid all under the front of my car on the garage floor. I just spent enough time and energy replacing the AC evaporator and so I don’t think I have the energy to tackle this DIY. I ordered a refurbished steering rack and will take it to my Indy here
@@bluesubie02 if you’re looking for someone to rebuild your current rack, i’ll do it! I’ve been working on a few tool designs to make this job easier too
@@beardedgarage I appreciate that, but I don’t have a lift so removal and reinstall would be difficult for me. I’m hoping the rebuilt unit from Steering Advantage works out for me. I’ll let you know how it turns out
@@bluesubie02 no worries, good luck. Let me know how good the rebuild looks and what you get with it
sounds great....cant wait to drive it!!!!
This was great! I found i didnt have to remove the interior bracket to get the bumpers off, you can remove them after. Was a time saver. Just had one bolt to remove underneath.
@@ElPapi-Boricua good advice, thanks!
Thanks a lot man! Really helpful video!
Is vaseline a safe assembly lubricant? Why not use a coating of the steering fluid?
@@fredreynolds1677 great question. Vaseline is petroleum based and used by lots of the old school guys as assembly lubricant. I have a few friends that have been doing it for 40 years
@@beardedgarage Thanks for the reply! Great video, appreciate the detailed commentary and hints. I think my rack needs a rebuild due to leaks...
I watched your video about ten times before and during this job. Thank for you the assist sir. Broke a couple clips on the plastic part and lost one bolt due to rust. Got it all put back together though.
@@joeyyknapp I’m glad it helped!
Yay for a fresh 993 video! Double yay for a steering rack video, couldn't come at a better time as I need to refurbish mine.
@@VladiDusil glad to hear it. Let me know if you need a hand!
make sure those oil levels are all correct then fire it UP!!!!!! Whens our next drive/trip??
@@paulbisaccia1332 Any day there’s sun, partner!
Great video
@@scottdavies8925 I’m glad you liked it!
Beautiful car there, dude
Hell yeah!
Thanks brother gonna try this before changing motor out
@@matthewcunningham1190 thanks for watching
The only detailed explanation of why the arms don't go on. You saved me hours. Nice job!
@@liammckin6478 I’m glad it helped!!
You have any ideas on why my blades won't engage, they were working and now stopped
Try checking all fuse housings under the seat, I had same problem with blades not working, turns out one of the fuse housing's was full of water 👍 hope that helps
Has anyone tried this on a ninebot s max
could you tell me where the cabin filter is on this truck
There’s not one.
Mine is flashing blue and won’t charge does anyone know a solution?
What manufacturer , make/ model is the torque wrench you are using. Thanks
That particular one is a precision instruments torque wrench. I bought that a bunch of years ago when precision instruments still had the contract for making snap on torque wrenches. Personally I own a bunch of different brands/models/sizes
Thank you. Excellent instruction video
Great, thanks
U SIIRRRRR ARE THE MEN.. THIS GOES TO SHOW U 2YRS LATER AND STILL HELPING PEOPLE OUT HERE.......ALWAYS POST UP DONT MATTER HOW MUCH TIME PASSES BY SOMEONE WILL ALWAYS NEED THIS HELP....THANK YOU SIR A MILLION TIMESSS....GREAT VIDEO AND EXPLANATION..
I’m glad it was helpful for you!
Fully support what you're doing, my dad has me doing the exact same, but I just need to know where the oil pan bolt is. But I'll give you a sub and view. Thank you
It’s not an oil pan bolt, it’s an oil hose that you drain so you can get the oil out of the frame
Great Video! Subscribed !
Much appreciated!
5:00 wtff is that kid laugh like a goof ... whyyyy???😅
I like how you don't re-use your adjectives for any of the asshats/idiots/etc throughout the whole video...keepin' it fresh! :D
Hahahhahahahajhajajajaja. Thank you, I laughed good at that one!
Should we clean the remaining oil that’s left inside the oil filter housing or is it ok to just dump the new filter on without wiping it down?
I tend to wipe everything down before I put it all back together. I like to make sure there’s no grit or dirt in and around the filter & housing
@@beardedgarage thank you
it cost me 150 CAD last time, I am gonna do it myself, thanks for sharing!
Good to hear! I waited on an oil sale and picked up a bunch! Now I’m doing Mobil 1, with Mobil filter for $19
Thanks for the great video!! The link doesnt work anymore tho:/ still have the link? I need one!
I just clicked the link and it worked, that pump is no longer available from Amazon. I think it’s just out of stock
Nice video! Very helpful! One thing I noticed you didn’t adjust the striped kit.
Great point. I checked the striping kit and it was adjusted properly (e.g. level). Unfortunately it doesn’t stripe my lawn well because “crab grass doesn’t stripe well”
Clumsy damaging way demonstrated to compress the pistons, best to use a brake pad compressor. A compressor doesn’t damage the face of the calliper.
To each his own. I’ve done it with pliers, screw drivers, compressor, etc. as I said in the video, I’m sanding and painting the calipers so I didn’t care about the face of the caliper.
Great video. I recently bought a 2006 f350 dually king Ranch, previous owner gave me the door code which also activates the ignition start. Please, do you know how I can deactivate this code? I have a fob now that I programmed to unlock and lock the doors. Thank you
Exactly the video I needed. Thanks!
I’m glad someone is watching!!
what degrees angle for sharping blades to sharper them
Most lawnmower blades are 30º
Can you share any other tips on getting that connector out? Last thing I want to do is break it. I’ve been working on it for about an hour
Are you talking about the fan connector with the red tab early on in the video? You have to get in there and look at it, the red piece pops out and then pull it apart. It’s a royal PITA, but it definitely comes apart
would use sandpaper disks as will leave a smother finish
Not a glamorous job, but certainly can be challenging! Nice work! 👍
I used the 3M adhesive and although it worked great on the felt strip, it didn’t adhere at all to the rubber strip. I had to strip that gunk off the sunroof but it left absolutely no residue stuck to the rubber. Any thoughts or any other adhesive recommendations?
I’d still use the same 3M adhesive, I’d just recommend using less than you think you should, apply to both sides (car and rubber strip) and let them get tacky before you put them together.
Thanks for the suggestions and thank you for posting what you do, adding an extra dimension to Porsche ownership!
I rubbed lacquer thinner on the rubber strip, let it dry, and it did wonders for the adhesion.
Awesome, thank you!
Beautiful car. The finest 911 series in my opinion. This is the only flaw on my 97 which I am getting ready to address thanks to your video. Thanks
Much appreciated, I’m actually glad someone is watching. We have a lot more videos, just need time to clean them up and get them posted.
Thank you!!! My end broke off and I was unable to fix it ... I bypassed it...and on mine the positive and negative was the same as yours. My son will be happy after school today!! Thanks again
Excellente video et tuto, fonctionne très bien pour la clée de ma 928.
Great video. Thank you. First year with mine so it’s nice to see a how to
I'm glad someone is watching.
@@beardedgarage I always use UA-cam for ideas. Especially tips and tricks to make things easier.
Having a hard time finding the C1K2 oil filter. I wonder if the part number changed.
@@voiceofreason4399 I think it's cross-referenced a few different times. Last I remember the other model number was 696854, but it might depend on the age of your machine.
Have you done hydraulic fluid? That's next for me
What part of the frame did you twist the radiator back to? I have the same issue and looking for a temp fix 8:59
I just rewatched this video and it looks like we just didn't show the jerry-rigging of radiator to the frame. Apologies for that. It's been a while, but we took the grill out and had access to to frame components on both sides of the radiator on the top. The factory clips were shot and I was able to wire those components to the frame behind the grill.