Відео

Trying to prepare for winters rain with leaky windows on ‘03. Seems like a lot but gotta do something :(

My allen wrench was junk

Exhaust cutout is easier on the walking money stack

Thx

OK, finally got it greased, very trick job. Used a thin needle Lincoln 5803 from Amazon. Rotate drive shaft till grease port down so I could barely see grease port, it is buried and it is hard to get the needle tip into the port, it does not lock on or anything, have to press needle into the port. with it at 90 degrees or straight up and down. Have to clean it off to see it. I could not get it lined up coming in front side of the carden joint, grease just leaked out around the grease port. With pistol grip grease gun, and long flex hose, come in from behind joint on rear wheel side of support bracket and angle needle into the port 90 degrees upwards Pumped in 10 pumps and red lithium grease came out the back of the ball (rear wheel side) carden joint. Horrible design, and I wonder how many actually can get this done right. I helped to come in from backside so I could see the needle and port better than being blocked by hand, The longer the flex hose the better.

Where did u get the seal kit from

Can you use a hands free for the phone on it

How did you get all the crud out of the bottom of the bowl?

OK, I finally found it again. IT is not on the cross joint, it is on the frame of the CV joint. I pumped a bunch of grease in like 20 pumps while pushing the broad needle tip into the fitting, but I am not impressed. I see a lot of grease seemed to have leaked out on the same side as the grease fitting, and I see none on the backside, so when it fails will be time for some new parts again. Definitely this a lousy design. Designed this way to guarantee future part sales. I had a DC joint on 62 Buick same kind of grease fitting, and I never greased it and it never failed.

in 2019, Dealer replaced front driveshaft when I got truck (2005 model). Is it possible the new one does not have grease fitting

I swore I thought I greased mine on my 3500 dually 4 door a few years ago. But today jacked tire and looked hard and I see nothing at all like in your vid. I have worked on many cars and trucks over decades, very familiar with that, and I cannot see it. Only options I have is remove driveshaft to get better look or ignore it.

If you are still getting leaks,,,it's the $ 8.00 gasket behind the 3rd brake light guy's. First thing to cause a leak on 97-03 f150

amazon dont sale it

I am about to do this to my recently passed dads 2003 Ford F150. I already tore out the carpet and only the front two seats remain!

Gracias a tu video me decidí a comprarlas... 👍🏽

Can't believe its that much bs to reseal a rear window

FYI there is a difference Between this map sensor for boost $200 ish and the aviant sensor located on the air intake box. $100 ish .. make sure both are good .. 👍

Great video! Blow your nose next time though or do the “farmers blow” closing off one nostril, blow hard then repeat on the other nostril. I was more focused on you sniffing than the video!😂😂😂Good video though what I could gleam from it. It looks like a nightmare but in actuality is just a little time consuming. Thanks for the video!

My grill broke and I need to remove or repair, or replace... Thanks for the post. I had a cat 40 years ago that would do the same thing while I was working on my car. Same colors as yours, as well. His name was Pumpkin.

I have one, Springfield dropped the ball on this one. CCI mini mag, 36 gr. HP do the best for me. But I love the gun just don't shoot well at all.

What size do you have and your weight.? Looking at the same coat have the extreme with cordura and its been abused and shows no wear. Thanks

My seat cushion is shot but the material is still pretty good so I'm going to attempt to replace the cushion. I like the idea of not taking the seat out of the truck. I'm going to try that also

What about left and right

The AR mag is designed to accept pcc mags like scorpion etc not pistol mags 😊

Can i find this on a 08 dodge ram?

Thanks very helpful

I got one in the sage colored stock a few months ago and really like it. I’m getting exceptional accuracy with Fiocchi Range Dynamics ammo.

Perhaps you could get footage of a larger load going down a steep incline.

Great video. Maybe spray some lubricant or put some anti sieze on the threads.

It actually axle nut has two Torx sir. The first torque is about 132 foot pounds to 149 foot pounds and this is on 2003 to 2005 dodge it doesn’t matter if it’s 2500 or 3500 4 x 4 then you spend the hub 5 to 10 times let the bearing sit and then final torque is. 263 foot pounds. I’m not going to use Nm You don’t want it over torque your hub bearings or under torque them you torque them at 300+ ft pounds that’s way over. You might’ve been thinking ( 357 Nm) Which is 263 foot pounds

Good to know!!

Boutta do mine appreciate it

I’ve been wanting to upgrade my dad’s 04 Dakota and this is perfect!!!

I got the seat cover for my 2013 Ram 1500 for $23 and the foam part on Amazon for $45. Its a different pattern than yours, and I needed to get D ring pliers which were $14 on Amazon to attach the seat cover to the foam.

I'll just pay the 700 dollars.

WARNING! Safety Violation! NEVER do mechanical work on equipment while wearing rings or jewelry. This should be common since? He is lucky to still have his finger! Also, when did he close the canister drain valve? Was there water or dirt in the drain bottle? How long between filter changes? What is the Cummins micron rating of the filter? Inadequate information to do a good job.

Great vid!

Hey, i know this is a lkng shot, but just wondering how the dorman one held up?

Only thing that i would say is to start with the Front to line up the stitching line's with the edges and round over part..then pull it all tight in the Rear... But Thank's .. Gives me a good idea and starting point of what's all involved in replacing the cover...

Actions are categorized as fast, MODERATE, slow. Its a medium power moderate action

Life's too short for slomo.

Need more dealerships here in the mid west states. Michigan

thanks

At first I was a bit disappointed at how much force it took to get the pistol mags in. Took leaving them in for several days to get it to loosen up some and now getting them out and re-indexing is a bit smoother while still having good retention.

Good lookin out brother. Very helpful

Awesome this video didnt show me how to remove it. Just said it was a pain. LOL love these videos that waste time.

Is the hub supposed to come apart in 2 peices? 😂 Mine did.

plastic gets tacky after a wile vanguard veo works well.

Literally proceeds to not film the only difficult part.

Suggestion. Mark the universal on the outside with a line ( paint or chalk) for quick identification for future. It also helps when rotating the universal to get access to the fitting