- 23
- 46 835
Chilli's Automotive
Приєднався 15 лют 2023
Welcome to Chilli's Automotive!! Just another automotive youtube channel trying to make it in this competitive market. However, as an ASE certified real world automotive technician, I'm certian I can provide you with some form of value, as well as entertainment.
2007 Chrysler 300c 5.7 EGR valve replacement (vehicle intermittently stalls when coming to a stop)
If your Chrysler 300c (or any Mopar product for that matter) is stalling when coming to a stop, 99% of the time it is the EGR (Exhaust Gas Recirculation) valve that has failed, which is the case with this 300 we have here. The main function of the EGR valve is to recirculate exhaust Gas back into the intake manifold for emissions purposes. When it fails, it negativity affects the air/fuel ratio and can cause sluggish performance and stalling when coming to a stop.
Below are some (affiliate) links for some products used in this video
EGR valve: amzn.to/4fnDBXV
Milwaukee insider: amzn.to/3Cje0km
Gloves: amzn.to/3CgcQ9l
#chrysler #300 #mopar #moparornocar
*Disclaimer: Due to circumstances beyond the power of Chilli's Automotive, I am unable to guarantee proper use of the information shared. Chilli's Automotive assumes no liability for injury or damage to property inflicted as a result of any information contained in this video. Information received from this video is to be used at your own risk. The use of safe practices and precautions are recommended by Chilli's Automotive while performing a repair of any sort using any category of tools that have been seen in this video. No information held in this video will produce any expressed or implied assurance or warranty of any certain result. Any damage, loss, or injury that may result from improper use of equipment, tools or information seen in this video is the the exclusive responsibility of the user and not Chilli's Automotive.
Below are some (affiliate) links for some products used in this video
EGR valve: amzn.to/4fnDBXV
Milwaukee insider: amzn.to/3Cje0km
Gloves: amzn.to/3CgcQ9l
#chrysler #300 #mopar #moparornocar
*Disclaimer: Due to circumstances beyond the power of Chilli's Automotive, I am unable to guarantee proper use of the information shared. Chilli's Automotive assumes no liability for injury or damage to property inflicted as a result of any information contained in this video. Information received from this video is to be used at your own risk. The use of safe practices and precautions are recommended by Chilli's Automotive while performing a repair of any sort using any category of tools that have been seen in this video. No information held in this video will produce any expressed or implied assurance or warranty of any certain result. Any damage, loss, or injury that may result from improper use of equipment, tools or information seen in this video is the the exclusive responsibility of the user and not Chilli's Automotive.
Переглядів: 122
Відео
2015 Chevy Malibu 2.5 spark plug replacement
Переглядів 2866 місяців тому
Replacing spark plugs on a Chevy Malibu, or any 4 banger for that matter, is very simple and can be done in under 10 minutes. Assuming you have all basic tools (Metric/SAE sockets, extensions, ratchets etc.) All of the specialty tools you might not have are linked below for your convenience. 5/8" spark plug socket: amzn.to/3XGWO0R Torx socket set: amzn.to/4cnhi3c #automotive #sparkplug #gm #che...
2007 Chrysler 300C front pads and rotors replacement
Переглядів 1317 місяців тому
Here you will see the procedure for replacing the front pads and rotors on a 1st gen 300C. This also applies to the Dodge Charger/Challenger and Magnum as well as the other 300 trim models (except for the SRT8). I hope you find this video helpful. All tools and supplies (including the repair manual) are linked below Chrysler 300 (2005-2018) repair manual: amzn.to/45CloSi Electric ratchet w/batt...
Ryobi GCV 160 3000 psi pressure washer won't start after sitting for over a year
Переглядів 8 тис.7 місяців тому
Nine out of ten times your pressure washer won't start after sitting for a long time because the fuel goes bad and gums up the carb. In this video you will see how to take it all apart and clean it and put it back together All of the tools and supplies I used will be linked below Carb cleaner: amzn.to/3yZHoKE Small flathead: amzn.to/4ckqBAg 10mm socket: amzn.to/3Vtinz5 An important note, it's v...
2014 Audi A4 driver side CV axle replacement
Переглядів 6 тис.Рік тому
In my opinion, replacing CV Axles on these models, is one of the easiest things in the world. Just watch and you will see. This is a great repair for DIYers so for those of you wanting to tackle this job, I have linked all the tools that you will need down below: Impact gun: amzn.to/48pSZzV Impact gun batteries: amzn.to/44VT1ww Hook/Pick set: amzn.to/3EK7Sj4 Sleeved Impact socket set: amzn.to/3...
There should NOT be this much play in the waterpump pulley!!!
Переглядів 68Рік тому
There should NOT be this much play in the waterpump pulley!!!
This is what I do with all of my blow molded cases (and so should you)
Переглядів 36Рік тому
A personal pet-peeve of mine is the foam that sits in the blow molded cases getting in my way. While I could just get rid of them, they do offer some protection to the contents. So here is my solution. Adhesive Spray: amzn.to/3Pv52U3 The product is linked above for your convenience, by purchasing through the link, I am awarded a small commission on qualifying items ant no additional cost to you...
Replacing front pads and rotors with the AI Presidents
Переглядів 135Рік тому
Replacing front pads and rotors with the AI Presidents
Low fan speeds not working on your vehicles hvac system? Watch this
Переглядів 86Рік тому
Low fan speeds not working on your vehicles hvac system? Watch this
Thank you I was about to go spend hundreds of dollars at a mechanic when I can do it myself
Thank you. I'm glad you found it helpful
Does air go both ways or just one way
You can blow air through it either way
Mines keep shutting off when i switch it from start to run 🤷🏽♂️ it won't stay crunk
You didn’t have to remove the upper control arms to move the steering knuckle out of the way….do you know if you have to move it for the passenger side?
The process for the passenger side is the same, the only difference is there is a metal heat shield you will have to remove, they are 3 m10 triple squares if I remember correctly. It is kindof a pain to remove but I've found the easiest way to be using a long reach ratchet and a stubby m10 triple square, working from from the engine bay
Hello, "Chilli's Automotive" I was analyzing your channel and saw that in your channel have some problem, That's why your channel is not much growing and not getting much engagement, If you can solve these problems, Your channel will grow like a storm. If you tell I can tell these problems. Where can I tell? Here or email?
Great job! At what mileage and age did you have to replace the CV axle?
Thanks. The car was approximately 10 years old and a little over 100k miles at the time of replacement.
Is it possible for axel to be a source of bad baring like noise?
I personally have never seen cases like that. But I suppose it's not impossible. The tell tale sign of an axle going bad is a clicking like noise while turning
great video.
I had an interesting problem, the choke butterfly was stuck in an unusual position and would not move. Somehow it went past the closed (choked) position and now was open and would not return being wedged in the space. The butterfly is a thin steel diaphragm that rotates on a plastic shaft that is actuated by the choke rod outside. You can see four (two each side buttons that hold it there. I tugged on it with vice grips and it slid out of the plastic rod, got it BACK into the proper position and pushed it back through. I am going to go ahead and clean the jets.
was it an expensive fix?
No, just a new inner tie rod
Your temp is that normal for you? Mine stays below half
It all depends on the liter size of the engine aswell as the environment the truck is used I was just in Las Vegas for 4 years and this temp in the video was my usual idle and running temp moved back to California and the temp stays below half aswell now it’s all environment based 🤙🏽but anything above 2 and a half quarters isn’t usually a good sign for example when running the ac if it spikes to high it’s a possible thermostat water pump or radiator cap problem I have the 2004 colly 3.5 inline 5 things a tank almost 350k miles and still dusts 04-17 silverados most tacomas and a lot more newer vehicles since the truck is well maintained just look it up if you have a issue the trucks so old now everyone has most likely ran into the issue you have and have a fix for it
Cual era la falla la espiga de caja o ña omocinetica
God malibus are so sexy I just love how you change its spark plugs
The Philip screw on top of the carb should be taken out. There's another jet under the screw that should be cleaned out with some carb cleaner. I believe it the low speed jet.
That took forever 😂😂🎉❤🎉
What is the size for the main hex bolt?
17mm hex
On my 2012 S4, the original axle hub bolt was a 19mm, My new GKN bolt is 17mm! Wtf!
@@gmr19that means it has been replaced already as the original is 17mm and the cheaper axles (trackmotive in my case) came with 19mm. The gkn is the oem supplier for the b8 audis so makes sense it has the oe bolt
Really nice and clear video! What kind of grease did you put on the new cv axle ?
I used brake caliper grease. I have the stuff I used linked in the description. You can also use anti seize
@@ChillisAutomotive thx for replying !
I noticed that my Audi b8 axle is also worn and the transmission is slipping. Might the Cv joint axle be the cause of that? Please assist 🙏🏼
I personally have never heard of a case where the cv axle caused a transmission to slip. However that doesn't mean it's not possible. The most likely reason for a transmission slipping is by low fluid level in the trans, or burned/worn clutch packs.
Looks pretty easy!
What size bit is that for the 6 bolts at the top of the axle?
M10 triple square
@@ChillisAutomotive thanks for the quick reply!
And do you know what torque i need to use for the main hex bolt?
@@zachschuler1222 200 nm (147 ft lbs) plus an additional 180 degrees. It's best to torque the bolt with the wheel on the car and sitting on the ground so it won't spin while you torque it. For some reason I didn't show the specs or the process in the video, In the future I will most likely make a revised video doing so the next time I replace one.
BOOM!
thats super funny
Vid looped around then I realized lmao
Don't mind the less than satisfactory camera skills. I had a fishing pole in one hand and the sun beating on my eyes.
What’s the story behind this one? 😂
A customer put diesel fuel in their car (gasoline engine) and stated they left the gas station and only made it about three or so blocks before the engine stalled.
You know some dumb mofo will take this shit to heart.
Best pro tip ever! I do this every oil change!
Not a problem just unsafe and what happens when you run out of oil
you should not post this. very sad.
No one intelligent enough to change their own oil is dumb enough to try this hack.
This is a joke. Please do not drain engine oil while the engine is running!!! amzn.to/3OUe3qI drain plug tool
Sounds too expensive put tape over the flashing light it should fix it
A tried and true repair
Had a vehicle come in the other day, brakes grinding after they were changed. Mind you we had fired the employee that had changed them, he LEFT one of the old pads in the bracket and put the new right in overtop... I have no clue how the caliper slipped over it but holy fuck I'm glad the dude is someone else's problem.
We all have that one guy😂
Control arms bent 🤷🏽♂️ not sure. Tell me
Inner tie rod developed a massive amount of play from the impact, the rack and pinion suffered damaged as well
What state are you in?
I'm in the mid west