Відео

Yes 250 ohms, no watts required

@ thank you 🤩

@@barrylawrence8516 welcome

@@twinaxel thanks

@@christinejchannel thanks po

250 po yung bili namin jan sa isang tali

Thanks

Welcome Sir

@@melhvacofficial1983 thanks

Ayos na ayos Sir

Service kami sir iba ibang planta

@@christinejchannel hello

Thank you 😊

Salt Meter gamitin mo, refractometer din sya pero ang unit ay %Salt, ang %brix ay sa matamis.

@@kennethjamesbonifacio1180 basta pag output (madalas to sa FM), yung negative wire na tinanggal dun yung positive probe ng calibrator, kapag loop (PT & LT) yung negative wire mong tinanggal dun yung negative ng probe

@@kennethjamesbonifacio1180 pag hindi nagreading baligtarin nyo lang, hindi naman masisira pag baligtad, wala lang reading o kaya negative reading

@@pinoycalibrationmaster noted po master, planning po change career hehe thank you master

@@kennethjamesbonifacio1180 ano ba work mo ngayon Sir

@@pinoycalibrationmaster bio-medical technician, master

@@kennethjamesbonifacio1180 Cge Sir good idea yan

@@kennethjamesbonifacio1180 RTD: resistance signal from sensor TC: millivolts TC always 2 wires RTD 2 wires, 3 wires, 4 wires Paano mo malalaman kung RTD o TC sa controller kapag ang controller ay 3 wires automatic RTD kung 2 wires pwedeng RTD o TC RTD sukatin mo resistance madalas PT 100 (100 ohms at zero degree) kaya kung hindi naman zero degree lampas 100 ohms yan Kung PT 1000 ang sensor nyan (1000 ohms at zero) Ang wire ng RTD ordinary wire lang Kung TC naman sukatin mo ang millivolts kapag negative lumabas baligtadin mo lang, madalas type K, pwede mo isearch ang table ng thermocouple type K vs temperature, may conversion nyan HJ-CJ Hot Junction ito yung actual temp ng sensor Cold Junction ito yung actual temp ng nakakabit sa controller kumbaga dulo ng wire yung nasa terminal Ex HJ / sensor 50 degree, CJ/ terminal 30 degree 50-30 = 20 degree yung 20 hanapin mo equivalent sa table, tingnan mo kung tama ang mV, dapat same yan Pero kung same temp yang HJ at CJ malamang zero mV yan, kapag nasa ambient lang yang sensor halos zero reading yan Hindi ordinary ang wire ng TC ang wire nito ay kung anong type ay iyon din ang wire Kung gusto mo lang maidentify kung TC o RTD ang 2 wire sa madaling paraan sukatin mo agad ng resistance kapag may reading RTD kapag wala matic TC(minsan brown or silver braided ang wire)

@@gidimanp5418 where are you from Sir/Mam

@@gidimanp5418 salazar.lemuel15@gmail.com you can email me

@@Ricky-h2z 250 ohms

@@pinoycalibrationmaster standard po ba yung 250 ohms master or depende sa type ng transmitter na e-calibrate? thanks

@@Ricky-h2z standard po yan to regulate 0-5Volts sa 4-20mA

@@kennethjamesbonifacio1180 pasok ka sa wet calibration, 1st Empty Calibration, wala dapat laman ang tank then Full Calibration lagyan mo yung tank ng 100% load

@@kennethjamesbonifacio1180 ua-cam.com/video/S7hSE_gpUIU/v-deo.htmlsi=KeDZEjL5PJm9P-DH May video pala ako, comment ka na lang ulit pag okay na

​@@pinoycalibrationmaster okay na po idol. dami talaga natutunan mga videos mo. thank you

@@kennethjamesbonifacio1180 welcome sir

@@MamaLolas0216 thanks mam

@@KarlArchivalLMella thanks 👍

Salamat po

Thanks

@@KarlArchivalLMella height difference para sa computation ng uncertainty yung diameter naman para sa accuracy

thank you master. Master paano po kapag horizontal type pressure gauge? hanggang saan po susukatin yung height? salamat master ❤

@@drextv1234 thanks po

@@aldrinabellera7220 bayad libre sa adonis

Thanks po

Thanks po

Thanks po

😂

@@SHIELAPIET thanks mam

@@kuletnazar4463 yung setting Sir gawin mong 160

@@kuletnazar4463 baka may problem ang sensor nyo Sir

@@pinoycalibrationmaster hi di ko Po kase alam Yung settings

@@KarlArchivalLMella yes sir

Use the manual

@@rampagemotovlog29 salamat po

@@narcisobalanonjr.9184 wala akong sample nyan Sir, walang pang demo

❤️

Salamat sa Dios

@@Ivanbulilan hindi kami nagbebenta Sir

@@narcant welcome

🤔

@@monethborromeo9653 salamat sa Dios

Thanks

@@DetectiveMetal thanks

@@meralynparisvlogs7328 thanks po

Wala pa ako nyan Sir

Thanks for visiting

Thanks po

Thanks for visiting